Page History
...
- (1) FMC is a LPC Connector (no gigabit transceivers) on TE0701: I2C and JTAG access over CPLD.
Separate TE0701_FMC_PINOUT table (PDF/XLSX) is available on: Trenz_Electronic Download-Pinout - (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
- (5) CL Connector is usable as Cameralink only with module that map LVDS pins to this connector
- (6) Works, but without carrier board modification out of specification: TE0701 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
- (7) PS battery operated voltage (1.2V–1.5V).
- (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage
TE0703
| ETH | SD Card | USB Host | Reset | User LEDs | USB UART | USB JTAG | |
|---|---|---|---|---|---|---|---|
| TE0710 |  |  , 3.3V B16 I/O |  |  | , 2 LEDs | | |
| TE0711 | | , 1.8V B16 I/O | , device only(14) | | | | |
| TE0712 | , 100 MBit | , 1.8V B13 I/O | | | | | |
| TE0713 | | , 1.8V B13 I/O | , device only(14) | | | | |
| TE0715-15 | | | | | | | |
TE0715-30  (2) | | | | | | | |
| TE0720 | | | | | | | |
| TE0741 (4) | | , MGTs | | | | | |
| TE0820 (2) | | (6) | | | | | |
| TE0821 (2) | | (6) | | | | | |
| TE0823 (2) | | (6) | | | | | |
| TE0841 (2)(3) | | , MGTs | | | | | |
| TEG2000 | | , 1.8V Bank SB I/O | | | , 1 LED | | |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
- (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
- (6) REV06 select correct SDIO voltage by jumper J11. REV05 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).
- (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage
...
- (12) FMC_VADJ powers VCCIOC connected to power input of Bank 34 VCCO34 on TE0720 needed to start up. In standard Firmware dip S3-2 can be used to switch ON FMC_VADJ without FMC installed.
- (13) FMC_VADJ powers VCCIOC connected to power input of Bank 65 VCCO_65 and VDDO0 of CLK0 on TE0820. In standard Firmware dip S3-2 can be used to switch ON FMC_VADJ without FMC installed. Select VADJ_FMC 1.8V (HP bank)!
- (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage
TEB2000
| ETH | SD Card | USB Host | Reset | User LEDs | USB UART | Debug UART | USB JTAG | |
|---|---|---|---|---|---|---|---|---|
| TEM0007 | | | | | | | | |
3rd Party Carrier
| Name | Manufacturer | Product Link | Trenz Shop |
|---|---|---|---|
| EMC2-DP | Sundance | PC/104 OneBank Carrier for SoC Modules | EMC2-DP |
oi110 | Sundance | oi110 – Dual CameraLink | --- |
oi111 | Sundance | oi111 – Dual SDI + Analog Video | --- |
oi115 | Sundance | oi115 – HDMI In / Out | --- |
...
Overview
Content Tools