You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 16 Next »

Legend:

  • (warning) : Attention: Carrier/Module combination only with special condition or PCB modification possible
  • (tick): Supported
  • (plus): Supported with limitations
  • (error): Not Supported
  • (question): Table currently not complete, see TRM of module and carrier

TE0701

 FMC(1)FMC VadjPMODSETHHDMICL ConnectorSD CardUSB HostVBATT
TE0710(plus)(question)(question)(question)(question)(error), N.C.(error), 1.8V B16 I/O(error)(error)
TE0711(plus)(question)(question)(question)(question)(question)(question)(error)(error)
TE0712(plus)(question)(question)(plus),100 MBit*(question)(error), MGT's(question)(error)(error)
TE0713(plus)(question)(question)(error)(question)(question)(question)(error)(error)
TE0715-15(plus)(tick)(question)(tick)(question)(error), MGT's(tick)(tick)(plus), RTC and Key RAM
TE0715-30 (warning)(2)(plus)(plus),Max 1.8V(question)(tick)(question)(error), MGT's(tick)(tick)(plus), RTC and Key RAM
TE0720(plus)(tick)(tick)(tick)(tick)(tick), LVDS(tick)(tick)(plus), RTC and Key RAM
TE0741 (warning)(4)(plus)(question)(question)(question)(question)(error), MGT's(error),MGT's(error)(error)
TE0820 (warning)(2)(question)(question)(question)(question)(question)(question)(question)(question)(question)
TE0841 (warning)(2)(3)(plus)(question)(question)(question)(question)(error), MGT's(error),MGT's(error)(plus), Key RAM
  • (1) FMC is a LPC Connector on TE0701: DP0_..., GBTCLK0_...  and TRST_L Pins are not connected. GA0 and GA1 set to GND. I2C and JTAG access over CPLD.
         Separate TE0701_FMC_PINOUT table (PDF/XLSX) is available on: Trenz_Electronic Download-Pinout
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
  • (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected

TE0703

 ETHSD CardUSB HostResetUser LEDsUSB UARTUSB JTAG
TE0710(question)(error), 1.8V B16 I/O(error)(tick)2(tick)(tick)
TE0711(question)(question)(error)(tick)(question)(tick)(tick)
TE0712(plus),100 MBit(question)(error)(tick)(question)(tick)(tick)
TE0713(question)(question)(error)(tick)(question)(tick)(tick)
TE0715-15(question)(question)(tick)(tick)(question)(tick)(tick)
TE0715-30 (warning)(2)(question)(question)(tick)(tick)(question)(tick)(tick)
TE0720(tick)(tick)(tick)(tick)(question)(tick)(tick)
TE0741 (warning)(4)(question)(error),MGT's(error)(tick)(question)(tick)(tick)
TE0820 (warning)(2)(tick)(tick)(tick)(question)(question)(tick)(tick)
TE0841 (warning)(2)(3)(question)(error),MGT's(error)(tick)(question)(tick)(tick)
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
  • (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected

TE0705

 PMODSETHSD CardUSB Host
TE0710(question)(question)(error), 1.8V B16 I/O(error)
TE0711(question)(question)(question)(error)
TE0712(question)100 MBit(question)(error)
TE0713(question)(question)(question)(error)
TE0715-15(question)(question)(tick)(tick)
TE0715-30 (warning)(2)(question)(question)(tick)(tick)
TE0720(tick)(tick)(tick)(tick)
TE0741 (warning)(4)(question)(question)(error),MGT's(error)
TE0820 (warning)(2)(question)(question)(question)(question)
TE0841 (warning)(2)(3)  (error),MGT's(error)
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
  • (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected

TE0706

 ETH1ETH2SD CardUSB Host
TE0710(question)(question)(error), 1.8V B16 I/O(error)
TE0711(question)(question)(question)(error)
TE0712100 MBit(question)(question)(error)
TE0713(question)(question)(question)(error)
TE0715-15(tick)(tick)(tick)(tick)
TE0715-30 (warning)(2)(tick)(tick)(tick)(tick)
TE0720(tick)(tick)(tick)(tick)
TE0741 (warning)(4)(question)(question)(error),MGT's(error)
TE0820 (warning)(2)(question)(question)(question)(question)
TE0841 (warning)(2)(3)(question)(question)(error),MGT's(error)
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
  • (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected

TEBA0841

  • No labels