You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 19 Next »

Legend:

  • (warning) : Attention: Carrier/Module combination only with special condition or PCB modification possible
  • (tick): Supported
  • (star): Supported with limitations
  • (error): Not Supported
  • (question): Table currently not complete, see TRM of module and carrier

TE0701

 FMC(1)FMC VadjPMODSETHHDMICL ConnectorSD CardUSB HostVBATT
TE0710(star)(question)(question)(question)(question)(error), N.C.(tick)(error)(error)
TE0711(star)(question)(question)(question)(question)(question)(question)(error)(error)
TE0712(star)(question)(question)(star),100 MBit*(question)MGT's(question)(error)(error)
TE0713(star)(question)(question)(error)(question)(question)(question)(error)(error)
TE0715-15(star)(tick)(question)(tick)(question)MGT's(tick)(tick)(star), RTC and Key RAM
TE0715-30 (warning)(2)(star)(star),Max 1.8V(question)(tick)(question)MGT's(tick)(tick)(star), RTC and Key RAM
TE0720(star)(tick)(tick)(tick)(tick)LVDS(tick)(tick)(star), RTC and Key RAM
TE0741 (warning)(4)(star)(question)(question)(question)(question)MGT's(error),MGT's(error)(error)
TE0820 (warning)(2)(question)(question)(question)(question)(question)(question)(question)(question)(question)
TE0841 (warning)(2)(3)(star)(question)(question)(question)(question)MGT's(error),MGT's(error)(star), Key RAM
  • (1) FMC is a LPC Connector on TE0701: DP0_..., GBTCLK0_...  and TRST_L Pins are not connected. GA0 and GA1 set to GND. I2C and JTAG access over CPLD.
         Separate TE0701_FMC_PINOUT table (PDF/XLSX) is available on: Trenz_Electronic Download-Pinout
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
  • (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected

 

CL Connector is usable as Cameralink only with module that map LVDS pins to this connector

TE0703

 ETHSD CardUSB HostResetUser LEDsUSB UARTUSB JTAG
TE0710(question)(error), 1.8V B16 I/O(error)(tick)(star),2(tick)(tick)
TE0711(question)(question)(error)(tick)(question)(tick)(tick)
TE0712(star),100 MBit(question)(error)(tick)(question)(tick)(tick)
TE0713(question)(question)(error)(tick)(question)(tick)(tick)
TE0715-15(question)(question)(tick)(tick)(question)(tick)(tick)
TE0715-30 (warning)(2)(question)(question)(tick)(tick)(question)(tick)(tick)
TE0720(tick)(tick)(tick)(tick)(question)(tick)(tick)
TE0741 (warning)(4)(question)(error),MGT's(error)(tick)(question)(tick)(tick)
TE0820 (warning)(2)(tick)(tick)(tick)(question)(question)(tick)(tick)
TE0841 (warning)(2)(3)(question)(error),MGT's(error)(tick)(question)(tick)(tick)
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
  • (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected

TE0705

 PMODSETHSD CardUSB Host
TE0710(question)(question)(error), 1.8V B16 I/O(error)
TE0711(question)(question)(question)(error)
TE0712(question)100 MBit(question)(error)
TE0713(question)(question)(question)(error)
TE0715-15(question)(question)(tick)(tick)
TE0715-30 (warning)(2)(question)(question)(tick)(tick)
TE0720(tick)(tick)(tick)(tick)
TE0741 (warning)(4)(question)(question)(error),MGT's(error)
TE0820 (warning)(2)(question)(question)(question)(question)
TE0841 (warning)(2)(3)  (error),MGT's(error)
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
  • (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected

TE0706

 ETH1ETH2SD CardUSB Host
TE0710(question)(question)(error), 1.8V B16 I/O(error)
TE0711(question)(question)(question)(error)
TE0712100 MBit(question)(question)(error)
TE0713(question)(question)(question)(error)
TE0715-15(tick)(tick)(tick)(tick)
TE0715-30 (warning)(2)(tick)(tick)(tick)(tick)
TE0720(tick)(tick)(tick)(tick)
TE0741 (warning)(4)(question)(question)(error),MGT's(error)
TE0820 (warning)(2)(question)(question)(question)(question)
TE0841 (warning)(2)(3)(question)(question)(error),MGT's(error)
  • (2) HP IO Banks only support 1.8V
  • (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
  • (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected

TEBA0841

  • No labels