Legend:

• : Attention: Carrier/Module combination only with special condition or PCB modification possible
• : Supported
• : Supported with limitations
• : Not Supported
• : Table currently not complete, see TRM of module and carrier

TE0701

	FMC(1)	FMC Vadj	PMODS	ETH	HDMI	CL Connector(5)	SD Card	USB Host	VBATT
TE0710					, N.C.	, N.C.	, 3.3V B16 I/O
TE0711							,1.8V B16 I/O
TE0712				,100 MBit*		,MGT's	,1.8V B13 I/O
TE0713						,MGT's	,1.8V B13 I/O
TE0715-15						,MGT's			, RTC and Key RAM
TE0715-30 (2)		,Max 1.8V				,MGT's			, RTC and Key RAM
TE0720						,LVDS			, RTC and Key RAM
TE0741 (4)						,MGT's	,MGT's
TE0820 (2)		,Max 1.8V				,MGT's	(6)		, PSBATT(7)
TE0841 (2)(3)						,MGT's	,MGT's		, Key RAM

• (1) FMC is a LPC Connector (no gigabit transceivers) on TE0701: I2C and JTAG access over CPLD.
       Separate TE0701_FMC_PINOUT table (PDF/XLSX) is available on: Trenz_Electronic Download-Pinout
• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
• (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
• (5) CL Connector is usable as Cameralink only with module that map LVDS pins to this connector
• (6) Works, but without carrier board modification out of specification: TE0701 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
• (7) PS battery operated voltage (1.2V–1.5V).

TE0703

	ETH	SD Card	USB Host	Reset	User LEDs	USB UART	USB JTAG
TE0710		, 3.3V B16 I/O			, 2 LEDs
TE0711		, 1.8V B16 I/O
TE0712	, 100 MBit	, 1.8V B13 I/O
TE0713		, 1.8V B13 I/O
TE0715-15
TE0715-30 (2)
TE0720
TE0741 (4)		, MGTs
TE0820 (2)		(6)
TE0841 (2)(3)		, MGTs

• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
• (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
• (6) REV06 select correct SDIO voltage by jumper J11. REV05 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).

TE0705

	PMODS	ETH	SD Card	USB Host
TE0710			, 3.3V B16 I/O
TE0711			,1.8V B16 I/O
TE0712		100 MBit	,1.8V B13 I/O
TE0713
TE0715-15
TE0715-30 (2)
TE0720
TE0741 (4)			,MGT's
TE0820 (2)			(6)
TE0841 (2)(3)			,MGT's

• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
• (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
• (6) Works, but without carrier board modification out of specification: TE0705 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.

TE0706

	ETH1	ETH2	SD Card	USB Host
TE0710			, 3.3V B16 I/O
TE0711			, 1.8V B16 I/O
TE0712	100 MBit		, 1.8V B13 I/O
TE0713
TE0715-15
TE0715-30 (2)
TE0720
TE0741 (4)			, MGTs
TE0820 (2)			(6)
TE0841 (2)(3)			, MGTs

• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
• (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
• (6) REV06 select correct SDIO voltage by jumper J11. REV05 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).

TEBA0841

	SFP	USB Host	SD Card "J4 2x5 Pin Header(2.54)"	GPIO "J20/J10 each 2x25 Pin Header(2.54)"	XMOD (JTAG/UART) "JX1 2x6 Pin Header (2.54)"	GPIO (JTAG/UART/MGT REFCLK) "J3 2x8 Pin Header(2.54)"
TE0710			,3.3V B16 I/O	(9)		(8)
TE0711			,1.8V B16 I/O	(9)		, B34 CLK input
TE0712			,  B13 I/O	(9)		, B34 CLK input
TE0713			,  B13 I/O	(9)
TE0715 (10)			(7)	(9)
TE0715-30 (10)			(7)	(9)
TE0720 (10)			(7)	(9)		, B34 CLK input
TE0741 (11)			,MGT's	(9)
TE0820 (10)			(6)	(9)
TE0841			,MGT's	(9)

• TEBA0841 has no dedicated power plug connector for 3.3V main power. External Power Supply must be connected to  J17, J20, J4 or J3 3.3V Pin. Do not use XMOD for power supply.
• TEBA0841-REV01 VCCIOB and VCCIOC are not connected.
• (6) Works, but without carrier board modification out of specification: TE0706 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
• (7) SD signals only, no SD-Card connector
• (8) CLK not connected on TE0710
• (9) Check schematics  or TE Master Pinout Excel Sheet for detailed connection and IO Bank power supply
• (10) With TEBA0841-01 is Boot Mode not selectable, please contact Trenz Electronic Support, if you need a Zynq or ZynqMP Module with TEBA0841-1. With TEBA0841-2 it's usable.
• (11) MGT polarity is swapped

TEF1002

	FMC	FMC Vadj	SFP	SATA	PCIe	USB Host	SD Card	Ethernet	FFA & FFB
TE0710							, 3.3V B16 I/O
TE0711							, 1.8V B16 I/O
TE0712							, 1.8V B13 I/O
TE0713							, 1.8V B13 I/O
TE0715
TE0715-30		, Max 1.8V
TE0720  (12)
TE0741							,MGTs
TE0820 (13)		, Max 1.8V
TE0841							,MGTs

• (12) FMC_VADJ powers VCCIOC connected to power input of Bank 34 VCCO34 on TE0720. In standard Firmware dip S3-2 can be used to switch ON FMC_VADJ without FMC installed. 
• (13) FMC_VADJ powers VCCIOC connected to power input of Bank 65 VCCO_65 on TE0820. In standard Firmware dip S3-2 can be used to switch ON FMC_VADJ without FMC installed. Select max 1.8V (HP bank)!