-------------------------------------------------------------------------------- TE0808 TE_XFsbl_HookPsuInit_Custom Configure Carrier I2C Switch 0x77 Configure PLL: SI5345-B Si534x Init Registers Write. Si534x Init Complete. Status 0xC:0x0, 0xE:0x0, 0xD:0x0, 0x11:0, 0xF:0 (...waiting for calibration...PLL Status Register 0xC:0x0, 0xE:0x0, 0xD:0x0, 0x11:0, 0xF:0. USB Reset Complete PCIe Reset Complete -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Xilinx Zynq MP First Stage Boot Loader (TE modified) Release 2021.2 Jul 28 2022 - 07:10:17 Device Name: XCZU15EG -------------------------------------------------------------------------------- TE0808 TE_XFsbl_BoardInit_Custom Configure Carrier I2C Switch 0x73 for EEPROM access Configure Carrier I2C Switch 0x77 to avoid conflicts with EEPROM -------------------------------------------------------------------------------- NOTICE: BL31: v2.4(release):xlnx_rebase_v2.4_2021.1_update1-23-g9188496b9 NOTICE: BL31: Built : 07:41:24, Oct 13 2021 U-Boot 2021.01 (Oct 12 2021 - 09:28:42 +0000) CPU: ZynqMP Silicon: v3 Board: Xilinx ZynqMP DRAM: 4 GiB PMUFW: v1.1 EL Level: EL2 Chip ID: zu15eg NAND: 0 MiB MMC: mmc@ff160000: 0, mmc@ff170000: 1 Loading Environment from FAT... Unable to use mmc 0:0... In: serial Out: serial Err: serial Bootmode: SD_MODE1 Reset reason: EXTERNAL Net: ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 1, interface rgmii-id eth0: ethernet@ff0e0000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found U-Boot script /boot.scr 2710 bytes read in 14 ms (188.5 KiB/s) ## Executing script at 20000000 Trying to load boot images from mmc1 21787136 bytes read in 1605 ms (12.9 MiB/s) 41749 bytes read in 17 ms (2.3 MiB/s) ## Flattened Device Tree blob at 00100000 Booting using the fdt blob at 0x100000 Loading Device Tree to 000000007dd04000, end 000000007dd11314 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.0-xilinx-v2021.2 (oe-user@oe-host) (aarch64-xilinx-linux-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP Tue Oct 12 09:30:57 UTC 2021 [ 0.000000] Machine model: xlnx,zynqmp [ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8') [ 0.000000] printk: bootconsole [cdns0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 512 MiB at 0x000000005dc00000 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000087fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fefffff] [ 0.000000] node 0: [mem 0x0000000800000000-0x000000087fffffff] [ 0.000000] Zeroed struct page in unavailable ranges: 256 pages [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000087fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 22 pages/cpu s49624 r8192 d32296 u90112 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1031940 [ 0.000000] Kernel command line: earlycon console=ttyPS0,115200 clk_ignore_unused root=/dev/mmcblk1p2 rw rootwait cma=512M [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x0000000059c00000-0x000000005dc00000] (64MB) [ 0.000000] Memory: 3500728K/4193280K available (14080K kernel code, 988K rwdata, 3964K rodata, 2112K init, 591K bss, 168264K reserved, 524288K cma-reserved) [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] irq-xilinx: /amba_pl@0/interrupt-controller@80000000: num_irq=32, sw_irq=0, edge=0x0 [ 0.000000] random: get_random_bytes called from start_kernel+0x31c/0x524 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 33.33MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x7b00c47c0, max_idle_ns: 440795202120 ns [ 0.000004] sched_clock: 56 bits at 33MHz, resolution 30ns, wraps every 2199023255541ns [ 0.008313] Console: colour dummy device 80x25 [ 0.012396] Calibrating delay loop (skipped), value calculated using timer frequency.. 66.66 BogoMIPS (lpj=133333) [ 0.022668] pid_max: default: 32768 minimum: 301 [ 0.027406] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.034617] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.043521] rcu: Hierarchical SRCU implementation. [ 0.047416] EFI services will not be available. [ 0.051805] smp: Bringing up secondary CPUs ... [ 0.056554] Detected VIPT I-cache on CPU1 [ 0.056594] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.057020] Detected VIPT I-cache on CPU2 [ 0.057046] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.057451] Detected VIPT I-cache on CPU3 [ 0.057477] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.057530] smp: Brought up 1 node, 4 CPUs [ 0.091608] SMP: Total of 4 processors activated. [ 0.096280] CPU features: detected: 32-bit EL0 Support [ 0.101384] CPU features: detected: CRC32 instructions [ 0.106524] CPU: All CPU(s) started at EL2 [ 0.110565] alternatives: patching kernel code [ 0.116181] devtmpfs: initialized [ 0.123251] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.127954] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.149442] pinctrl core: initialized pinctrl subsystem [ 0.149886] DMI not present or invalid. [ 0.153045] NET: Registered protocol family 16 [ 0.158453] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.164374] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.172166] audit: initializing netlink subsys (disabled) [ 0.177637] audit: type=2000 audit(0.116:1): state=initialized audit_enabled=0 res=1 [ 0.178042] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.191997] ASID allocator initialised with 65536 entries [ 0.197424] Serial: AMBA PL011 UART driver [ 0.228539] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.229609] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.236269] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.242926] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 1.443819] cryptd: max_cpu_qlen set to 1000 [ 1.471796] DRBG: Continuing without Jitter RNG [ 1.554627] raid6: neonx8 gen() 1859 MB/s [ 1.622691] raid6: neonx8 xor() 1398 MB/s [ 1.690765] raid6: neonx4 gen() 1908 MB/s [ 1.758828] raid6: neonx4 xor() 1367 MB/s [ 1.826918] raid6: neonx2 gen() 1813 MB/s [ 1.894982] raid6: neonx2 xor() 1253 MB/s [ 1.963066] raid6: neonx1 gen() 1550 MB/s [ 2.031131] raid6: neonx1 xor() 1067 MB/s [ 2.099223] raid6: int64x8 gen() 1258 MB/s [ 2.167287] raid6: int64x8 xor() 674 MB/s [ 2.235358] raid6: int64x4 gen() 1397 MB/s [ 2.303430] raid6: int64x4 xor() 713 MB/s [ 2.371521] raid6: int64x2 gen() 1224 MB/s [ 2.439595] raid6: int64x2 xor() 655 MB/s [ 2.507687] raid6: int64x1 gen() 902 MB/s [ 2.575741] raid6: int64x1 xor() 452 MB/s [ 2.575780] raid6: using algorithm neonx4 gen() 1908 MB/s [ 2.579737] raid6: .... xor() 1367 MB/s, rmw enabled [ 2.584668] raid6: using neon recovery algorithm [ 2.589746] iommu: Default domain type: Translated [ 2.594349] SCSI subsystem initialized [ 2.597969] usbcore: registered new interface driver usbfs [ 2.603302] usbcore: registered new interface driver hub [ 2.608571] usbcore: registered new device driver usb [ 2.613617] mc: Linux media interface: v0.10 [ 2.617819] videodev: Linux video capture interface: v2.00 [ 2.623290] EDAC MC: Ver: 3.0.0 [ 2.626758] zynqmp-ipi-mbox mailbox@ff990400: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.635042] FPGA manager framework [ 2.638339] Advanced Linux Sound Architecture Driver Initialized. [ 2.644588] Bluetooth: Core ver 2.22 [ 2.647826] NET: Registered protocol family 31 [ 2.652226] Bluetooth: HCI device and connection manager initialized [ 2.658543] Bluetooth: HCI socket layer initialized [ 2.663385] Bluetooth: L2CAP socket layer initialized [ 2.668407] Bluetooth: SCO socket layer initialized [ 2.673540] clocksource: Switched to clocksource arch_sys_counter [ 2.679463] VFS: Disk quotas dquot_6.6.0 [ 2.683242] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 2.694662] NET: Registered protocol family 2 [ 2.695081] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 2.702876] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 2.710928] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) [ 2.718400] TCP: Hash tables configured (established 32768 bind 32768) [ 2.724531] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 2.731196] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 2.738378] NET: Registered protocol family 1 [ 2.742854] RPC: Registered named UNIX socket transport module. [ 2.748428] RPC: Registered udp transport module. [ 2.753087] RPC: Registered tcp transport module. [ 2.757756] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.764823] PCI: CLS 0 bytes, default 64 [ 2.797193] Initialise system trusted keyrings [ 2.797324] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 2.803177] NFS: Registering the id_resolver key type [ 2.807436] Key type id_resolver registered [ 2.811575] Key type id_legacy registered [ 2.815574] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.822237] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 2.870126] NET: Registered protocol family 38 [ 2.870182] xor: measuring software checksum speed [ 2.878459] 8regs : 2068 MB/sec [ 2.882518] 32regs : 2449 MB/sec [ 2.887283] arm64_neon : 2083 MB/sec [ 2.887321] xor: using function: 32regs (2449 MB/sec) [ 2.891684] Key type asymmetric registered [ 2.895748] Asymmetric key parser 'x509' registered [ 2.900613] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.907946] io scheduler mq-deadline registered [ 2.912442] io scheduler kyber registered [ 2.918610] ps_pcie_dma init() [ 2.947385] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.949234] Serial: AMBA driver [ 2.953685] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 2.962304] brd: module loaded [ 2.967162] loop: module loaded [ 2.968610] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.972632] libphy: Fixed MDIO Bus: probed [ 2.976578] tun: Universal TUN/TAP device driver, 1.6 [ 2.980251] CAN device driver interface [ 2.984731] usbcore: registered new interface driver asix [ 2.989367] usbcore: registered new interface driver ax88179_178a [ 2.995402] usbcore: registered new interface driver cdc_ether [ 3.001196] usbcore: registered new interface driver net1080 [ 3.006818] usbcore: registered new interface driver cdc_subset [ 3.012705] usbcore: registered new interface driver zaurus [ 3.018248] usbcore: registered new interface driver cdc_ncm [ 3.024730] usbcore: registered new interface driver uas [ 3.029153] usbcore: registered new interface driver usb-storage [ 3.035725] rtc_zynqmp ffa60000.rtc: registered as rtc0 [ 3.040292] rtc_zynqmp ffa60000.rtc: setting system clock to 1970-01-01T00:00:05 UTC (5) [ 3.048370] i2c /dev entries driver [ 3.053456] usbcore: registered new interface driver uvcvideo [ 3.057488] USB Video Class driver (1.1.1) [ 3.062085] Bluetooth: HCI UART driver ver 2.3 [ 3.065968] Bluetooth: HCI UART protocol H4 registered [ 3.071068] Bluetooth: HCI UART protocol BCSP registered [ 3.076359] Bluetooth: HCI UART protocol LL registered [ 3.081448] Bluetooth: HCI UART protocol ATH3K registered [ 3.086827] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 3.093075] Bluetooth: HCI UART protocol Intel registered [ 3.098417] Bluetooth: HCI UART protocol QCA registered [ 3.103618] usbcore: registered new interface driver bcm203x [ 3.109243] usbcore: registered new interface driver bpa10x [ 3.114779] usbcore: registered new interface driver bfusb [ 3.120225] usbcore: registered new interface driver btusb [ 3.125687] usbcore: registered new interface driver ath3k [ 3.131190] EDAC MC: ECC not enabled [ 3.134775] EDAC DEVICE0: Giving out device to module edac controller cache_err: DEV edac (POLLED) [ 3.143730] EDAC DEVICE1: Giving out device to module zynqmp-ocm-edac controller zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT) [ 3.155958] sdhci: Secure Digital Host Controller Interface driver [ 3.161807] sdhci: Copyright(c) Pierre Ossman [ 3.166130] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.172107] ledtrig-cpu: registered to indicate activity on CPUs [ 3.177734] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 3.184161] zynqmp_firmware_probe Platform Management API v1.1 [ 3.189921] zynqmp_firmware_probe Trustzone version v1.0 [ 3.257743] securefw securefw: securefw probed [ 3.258020] alg: No test for xilinx-zynqmp-aes (zynqmp-aes) [ 3.262205] zynqmp_aes firmware:zynqmp-firmware:zynqmp-aes: AES Successfully Registered [ 3.270339] alg: No test for xilinx-keccak-384 (zynqmp-keccak-384) [ 3.276478] alg: No test for xilinx-zynqmp-rsa (zynqmp-rsa) [ 3.281990] usbcore: registered new interface driver usbhid [ 3.287354] usbhid: USB HID core driver [ 3.294120] ARM CCI_400_r1 PMU driver probed [ 3.294621] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered [ 3.302273] usbcore: registered new interface driver snd-usb-audio [ 3.308839] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 3.316145] Initializing XFRM netlink socket [ 3.319783] NET: Registered protocol family 10 [ 3.324561] Segment Routing with IPv6 [ 3.327930] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.334005] NET: Registered protocol family 17 [ 3.338052] NET: Registered protocol family 15 [ 3.342463] can: controller area network core [ 3.346809] NET: Registered protocol family 29 [ 3.351191] can: raw protocol [ 3.354132] can: broadcast manager protocol [ 3.358285] can: netlink gateway - max_hops=1 [ 3.362686] Bluetooth: RFCOMM TTY layer initialized [ 3.367457] Bluetooth: RFCOMM socket layer initialized [ 3.372564] Bluetooth: RFCOMM ver 1.11 [ 3.376278] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 3.381549] Bluetooth: BNEP filters: protocol multicast [ 3.386748] Bluetooth: BNEP socket layer initialized [ 3.391670] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 3.397554] Bluetooth: HIDP socket layer initialized [ 3.402614] 9pnet: Installing 9P2000 support [ 3.406741] Key type dns_resolver registered [ 3.411094] registered taskstats version 1 [ 3.415026] Loading compiled-in X.509 certificates [ 3.420838] Btrfs loaded, crc32c=crc32c-generic [ 3.434004] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 56, base_baud = 6249999) is a xuartps [ 3.443028] printk: console [ttyPS0] enabled [ 3.443028] printk: console [ttyPS0] enabled [ 3.447323] printk: bootconsole [cdns0] disabled [ 3.447323] printk: bootconsole [cdns0] disabled [ 3.456654] of-fpga-region fpga-full: FPGA Region probed [ 3.466728] nwl-pcie fd0e0000.pcie: host bridge /axi/pcie@fd0e0000 ranges: [ 3.473631] nwl-pcie fd0e0000.pcie: MEM 0x00e0000000..0x00efffffff -> 0x00e0000000 [ 3.481639] nwl-pcie fd0e0000.pcie: MEM 0x0600000000..0x07ffffffff -> 0x0600000000 [ 3.489712] nwl-pcie fd0e0000.pcie: Link is DOWN [ 3.494497] nwl-pcie fd0e0000.pcie: PCI host bridge to bus 0000:00 [ 3.500679] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.506161] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 3.513033] pci_bus 0000:00: root bus resource [mem 0x600000000-0x7ffffffff pref] [ 3.520535] pci 0000:00:00.0: [10ee:d021] type 01 class 0x060400 [ 3.526601] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 3.535527] pci 0000:00:00.0: PCI bridge to [bus 01-0c] [ 3.540849] ps_pcie_dma 0000:00:00.0: PS PCIe DMA Driver probe [ 3.547057] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success [ 3.554265] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success [ 3.561472] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success [ 3.568681] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success [ 3.575881] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success [ 3.583084] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success [ 3.590288] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success [ 3.597491] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success [ 3.604752] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success [ 3.611954] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success [ 3.619161] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success [ 3.626357] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success [ 3.633568] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success [ 3.640774] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success [ 3.647977] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success [ 3.655182] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success [ 3.662649] xilinx-zynqmp-dpdma fd4c0000.dma-controller: Xilinx DPDMA engine is probed [ 3.671550] zynqmp-display fd4a0000.display: vtc bridge property not present [ 3.680568] xilinx-dp-snd-codec fd4a0000.display:zynqmp_dp_snd_codec0: Xilinx DisplayPort Sound Codec probed [ 3.690759] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm0: Xilinx DisplayPort Sound PCM probed [ 3.698943] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm1: Xilinx DisplayPort Sound PCM probed [ 3.707610] xilinx-dp-snd-card fd4a0000.display:zynqmp_dp_snd_card: ASoC: no DMI vendor name! [ 3.716499] xilinx-dp-snd-card fd4a0000.display:zynqmp_dp_snd_card: Xilinx DisplayPort Sound Card probed [ 3.726084] OF: graph: no port node found in /axi/display@fd4a0000 [ 3.732663] xlnx-drm xlnx-drm.0: bound fd4a0000.display (ops 0xffff800010e9b9c8) [ 3.925079] Console: switching to colour frame buffer device 240x67 [ 3.948026] zynqmp-display fd4a0000.display: [drm] fb0: xlnxdrmfb frame buffer device [ 3.956177] [drm] Initialized xlnx 1.0.0 20130509 for fd4a0000.display on minor 0 [ 3.963692] zynqmp-display fd4a0000.display: ZynqMP DisplayPort Subsystem driver probed [ 3.972148] ahci-ceva fd0c0000.ahci: supply ahci not found, using dummy regulator [ 3.979711] ahci-ceva fd0c0000.ahci: supply phy not found, using dummy regulator [ 3.987137] ahci-ceva fd0c0000.ahci: supply target not found, using dummy regulator [ 3.994936] ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 4.003910] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 4.014582] scsi host0: ahci-ceva [ 4.018214] scsi host1: ahci-ceva [ 4.021665] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 53 [ 4.029584] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 53 [ 4.038537] spi-nor spi0.0: trying to lock already unlocked area [ 4.044541] spi-nor spi0.0: mt25qu512a (131072 Kbytes) [ 4.049713] 4 fixed-partitions partitions found on MTD device spi0.0 [ 4.056067] Creating 4 MTD partitions on "spi0.0": [ 4.060857] 0x000000000000-0x000000a00000 : "boot" [ 4.066541] 0x000000a00000-0x000000a40000 : "bootenv" [ 4.072366] 0x000000a40000-0x000002a40000 : "kernel" [ 4.078100] 0x000002a40000-0x000002ac0000 : "bootscr" [ 4.085094] macb ff0e0000.ethernet: Not enabling partial store and forward [ 4.092723] libphy: MACB_mii_bus: probed [ 4.097495] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 39 (68:27:19:ae:35:57) [ 4.107726] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM [ 4.114353] xilinx-axipmon fd0b0000.perf-monitor: Probed Xilinx APM [ 4.120921] xilinx-axipmon fd490000.perf-monitor: Probed Xilinx APM [ 4.127491] xilinx-axipmon ffa10000.perf-monitor: Probed Xilinx APM [ 4.150231] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 4.155732] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 4.163507] xhci-hcd xhci-hcd.1.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x0000000002010810 [ 4.172923] xhci-hcd xhci-hcd.1.auto: irq 95, io mem 0xfe200000 [ 4.179063] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 4.187338] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.194557] usb usb1: Product: xHCI Host Controller [ 4.199436] usb usb1: Manufacturer: Linux 5.10.0-xilinx-v2021.2 xhci-hcd [ 4.206133] usb usb1: SerialNumber: xhci-hcd.1.auto [ 4.211318] hub 1-0:1.0: USB hub found [ 4.215101] hub 1-0:1.0: 1 port detected [ 4.219236] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 4.224728] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 4.232400] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 4.239176] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 4.247440] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.254656] usb usb2: Product: xHCI Host Controller [ 4.259532] usb usb2: Manufacturer: Linux 5.10.0-xilinx-v2021.2 xhci-hcd [ 4.266227] usb usb2: SerialNumber: xhci-hcd.1.auto [ 4.271397] hub 2-0:1.0: USB hub found [ 4.275158] hub 2-0:1.0: 1 port detected [ 4.280469] i2c i2c-0: Added multiplexed i2c bus 2 [ 4.285394] i2c i2c-0: Added multiplexed i2c bus 3 [ 4.290334] i2c i2c-0: Added multiplexed i2c bus 4 [ 4.295267] i2c i2c-0: Added multiplexed i2c bus 5 [ 4.300215] i2c i2c-0: Added multiplexed i2c bus 6 [ 4.305276] at24 7-0050: supply vcc not found, using dummy regulator [ 4.312253] at24 7-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write [ 4.318997] i2c i2c-0: Added multiplexed i2c bus 7 [ 4.323969] i2c i2c-0: Added multiplexed i2c bus 8 [ 4.328899] i2c i2c-0: Added multiplexed i2c bus 9 [ 4.333704] pca954x 0-0073: registered 8 multiplexed busses for I2C switch pca9548 [ 4.341729] i2c i2c-0: Added multiplexed i2c bus 10 [ 4.346761] i2c i2c-0: Added multiplexed i2c bus 11 [ 4.351791] i2c i2c-0: Added multiplexed i2c bus 12 [ 4.351805] ata2: SATA link down (SStatus 0 SControl 330) [ 4.356810] i2c i2c-0: Added multiplexed i2c bus 13 [ 4.362098] ata1: SATA link down (SStatus 0 SControl 330) [ 4.367090] i2c i2c-0: Added multiplexed i2c bus 14 [ 4.377338] i2c i2c-0: Added multiplexed i2c bus 15 [ 4.382408] i2c i2c-0: Added multiplexed i2c bus 16 [ 4.387434] i2c i2c-0: Added multiplexed i2c bus 17 [ 4.392318] pca954x 0-0077: registered 8 multiplexed busses for I2C switch pca9548 [ 4.399925] cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 41 [ 4.406291] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer with timeout 60s [ 4.413845] cdns-wdt ff150000.watchdog: Xilinx Watchdog Timer with timeout 10s [ 4.424585] of_cfs_init [ 4.427071] of_cfs_init: OK [ 4.430025] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 4.453541] mmc0: SDHCI controller on ff160000.mmc [ff160000.mmc] using ADMA 64-bit [ 4.453545] mmc1: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit [ 4.487238] mmc1: new high speed SDHC card at address 59b4 [ 4.493140] mmcblk1: mmc1:59b4 USD00 14.7 GiB [ 4.498873] mmcblk1: p1 p2 [ 4.506716] random: fast init done [ 4.527336] mmc0: new high speed MMC card at address 0001 [ 4.533094] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB [ 4.537817] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB [ 4.543929] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB [ 4.549938] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB, chardev (244:0) [ 4.565556] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 4.583090] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 4.589627] clk: Not disabling unused clocks [ 4.594142] ALSA device list: [ 4.597107] #0: DisplayPort monitor [ 4.601076] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 4.609692] cfg80211: failed to load regulatory.db [ 4.630437] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 4.638553] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 4.645003] devtmpfs: mounted [ 4.648598] Freeing unused kernel memory: 2112K [ 4.653594] Run /sbin/init as init process [ 4.717808] usb 1-1: New USB device found, idVendor=04b4, idProduct=650a, bcdDevice=50.00 [ 4.725994] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 INIT: version 2.97 booting[ 4.783116] hub 1-1:1.0: USB hub found [ 4.786981] hub 1-1:1.0: 4 ports detected [ 4.846963] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd [ 4.873798] usb 2-1: New USB device found, idVendor=04b4, idProduct=6508, bcdDevice=50.00 [ 4.881993] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 4.943115] hub 2-1:1.0: USB hub found [ 4.947079] hub 2-1:1.0: 4 ports detected Starting udev [ 5.145562] usb 1-1.4: new high-speed USB device number 3 using xhci-hcd [ 5.225404] udevd[273]: starting version 3.2.9 [ 5.245981] random: udevd: uninitialized urandom read (16 bytes read) [ 5.252831] random: udevd: uninitialized urandom read (16 bytes read) [ 5.254832] usb 1-1.4: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98 [ 5.259309] random: udevd: uninitialized urandom read (16 bytes read) [ 5.267627] usb 1-1.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 5.281360] usb 1-1.4: Product: USB2.0 Hub [ 5.327343] hub 1-1.4:1.0: USB hub found [ 5.331579] hub 1-1.4:1.0: 4 ports detected [ 5.339321] udevd[274]: starting eudev-3.2.9 [ 5.457287] zocl: loading out-of-tree module taints kernel. [ 5.467125] [drm] Probing for xlnx,zocl [ 5.471316] zocl-drm a0000000.zyxclmm_drm: IRQ index 32 not found [ 5.477631] [drm] FPGA programming device pcap founded. [ 5.482892] [drm] PR Isolation addr 0x0 [ 5.483869] [drm] Initialized zocl 0.0.0 00000 for a0000000.zyxclmm_drm on minor 1 [ 5.496429] [drm] Probing for xlnx,zocl [ 5.500717] zocl-drm amba_pl@0:zyxclmm_drm: IRQ index 32 not found [ 5.507082] [drm] FPGA programming device pcap founded. [ 5.512325] [drm] PR Isolation addr 0x0 [ 5.513568] [drm] Initialized zocl 0.0.0 00000 for amba_pl@0:zyxclmm_drm on minor 2 [ 5.677604] usb 1-1.4.1: new low-speed USB device number 4 using xhci-hcd [ 5.814625] usb 1-1.4.1: New USB device found, idVendor=04d9, idProduct=0006, bcdDevice= 1.10 [ 5.823224] usb 1-1.4.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.830765] usb 1-1.4.1: Product: RPI Wired Keyboard 1 [ 5.835954] usb 1-1.4.1: Manufacturer: [ 5.947683] input: RPI Wired Keyboard 1 as /devices/platform/axi/ff9d0000.usb0/fe200000.dwc3/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4.1/1-1.4.1:1.0/0003:04D9:0006.0001/input/input0 [ 6.022009] hid-generic 0003:04D9:0006.0001: input: USB HID v1.11 Keyboard [ RPI Wired Keyboard 1] on usb-xhci-hcd.1.auto-1.4.1/input0 [ 6.044803] input: RPI Wired Keyboard 1 as /devices/platform/axi/ff9d0000.usb0/fe200000.dwc3/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4.1/1-1.4.1:1.1/0003:04D9:0006.0002/input/input1 [ 6.090537] FAT-fs (mmcblk1p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 6.117770] hid-generic 0003:04D9:0006.0002: input: USB HID v1.11 Device [ RPI Wired Keyboard 1] on usb-xhci-hcd.1.auto-1.4.1/input1 [ 6.209559] usb 1-1.4.4: new low-speed USB device number 5 using xhci-hcd [ 6.317789] usb 1-1.4.4: New USB device found, idVendor=0458, idProduct=0186, bcdDevice=24.58 [ 6.326312] usb 1-1.4.4: New USB device strings: Mfr=4, Product=40, SerialNumber=0 [ 6.333884] usb 1-1.4.4: Product: Wired Mouse [ 6.338239] usb 1-1.4.4: Manufacturer: KYE SYSTEMS CORP. [ 6.385556] input: KYE SYSTEMS CORP. Wired Mouse as /devices/platform/axi/ff9d0000.usb0/fe200000.dwc3/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4.4/1-1.4.4:1.0/0003:0458:0186.0003/input/input2 [ 6.402186] hid-generic 0003:0458:0186.0003: input: USB HID v1.11 Mouse [KYE SYSTEMS CORP. Wired Mouse] on usb-xhci-hcd.1.auto-1.4.4/input0 [ 6.414884] usbhid 1-1.4.4:1.1: couldn't find an input interrupt endpoint [ 6.619684] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null) bootlogd: /dev/ttyPS0Fri Mar 9 12:49:21 UTC 2018 INIT: Entering runlevel: 5 Configuring network interfaces... udhcpc: started, v1.32.0 udhcpc: sending discover udhcpc: sending discover udhcpc: sending discover udhcpc: sending select for 192.168.13.18 udhcpc: lease of 192.168.13.18 obtained, lease time 3600 /etc/udhcpc.d/50default: Adding DNS 147.231.12.1 /etc/udhcpc.d/50default: Adding DNS 147.231.10.9 /etc/udhcpc.d/50default: Adding DNS 8.8.8.8 done. Starting system message bus: dbus. Starting random number generator daemon. Starting haveged: haveged: command socket is listening at fd 3 haveged: haveged starting up haveged: haveged: ver: 1.9.13; arch: generic; vend: ; build: (gcc 10.2.0 CTV); collect: 128K haveged: haveged: cpu: (VC); data: 16K (D); inst: 16K (D); idx: 11/40; sz: 15456/64452 haveged: haveged: tot tests(BA8): A:1/1 B:1/1 continuous tests(B): last entropy estimate 7.99931 haveged: haveged: fills: 0, generated: 0 Starting OpenBSD Secure Shell server: sshd done. Starting Xserver Starting rpcbind daemon... done. starting statd: X.Org X Server 1.20.9 X Protocol Version 11, Revision 0 Build Operating System: Linux Current Operating System: Linux petalinux 5.10.0-xilinx-v2021.2 #1 SMP Tue Oct 12 09:30:57 UTC 2021 aarch64 Kernel command line: earlycon console=ttyPS0,115200 clk_ignore_unused root=/dev/mmcblk1p2 rw rootwait cma=512M Build Date: 25 August 2020 03:40:19PM Current version of pixman: 0.40.0 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Fri Mar 9 12:49:31 2018 (==) Using config file: "/etc/X11/xorg.conf" (==) Using system config directory "/usr/share/X11/xorg.conf.d" done starting Busybox HTTP Daemon: httpd... done. Starting internet superserver: inetd. NFS daemon support not enabled in kernel Init Start Run init.sh from SD card Load SD Init Script User bash Code can be inserted here and put init.sh on SD Init End Starting syslogd/klogd: done Starting internet superserver: xinetd. Starting watchdog daemon...done Starting tcf-agent: OK PetaLinux 2021.2 petalinux ttyPS0 D-BUS per-session daemon address is: unix:abstract=/tmp/dbus-ZnJm32ZNtm,guid=029dcb6bf5946877710731085aa282dd root@petalinux:~# matchbox: Cant find a keycode for keysym 269025056 matchbox: ignoring key shortcut XF86Calendar=!$contacts matchbox: Cant find a keycode for keysym 2809 matchbox: ignoring key shortcut telephone=!$dates matchbox: Cant find a keycode for keysym 269025050 matchbox: ignoring key shortcut XF86Start=!matchbox-remote -desktop [settings daemon] Forking. run with -n to prevent fork dbus-daemon[893]: Activating service name='org.a11y.atspi.Registry' requested by ':1.0' (uid=0 pid=889 comm="matchbox-panel --start-applets showdesktop,windows") dbus-daemon[893]: Successfully activated service 'org.a11y.atspi.Registry' SpiRegistry daemon is running with well-known name - org.a11y.atspi.Registry ** (matchbox-desktop:888): WARNING **: 12:49:36.578: Error loading icon: Icon 'terminal' not present in theme Sato root@petalinux:~# ifconfig eth0 Link encap:Ethernet HWaddr 68:27:19:AE:35:57 inet addr:192.168.13.18 Bcast:192.168.13.255 Mask:255.255.255.0 inet6 addr: fe80::6a27:19ff:feae:3557/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:658 (658.0 B) TX bytes:1906 (1.8 KiB) Interrupt:39 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:2 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:140 (140.0 B) TX bytes:140 (140.0 B) root@petalinux:~# cd /media/sd-mmcblk1p1/ root@petalinux:/media/sd-mmcblk1p1# ./test_vadd krnl_vadd.xclbin INFO: Reading krnl_vadd.xclbin Loading: 'krnl_vadd.xclbin' Trying to program device[0]: edge Device[0]: program successful! TEST PASSED root@petalinux:/media/sd-mmcblk1p1# root@petalinux:/media/sd-mmcblk1p1# halt Broadcast mes The system is going down for system halt NOW! INIT: Sending processes configured via /etc/inittab the TERM signal root@petalinux:/media/sd-mmcblk1p1# Stopping haveged: Stopping OpenBSD Secure Shell server: sshdstopped /usr/sbin/sshd (pid 743) . stopping Busybox HTTP Daemon: httpd... stopped httpd (pid 771) done. Stopping system message bus: dbus. Stopping internet superserver: inetd. stopping mountd: done stopping nfsd: done Stop. Stopping syslogd/klogd: stopped syslogd (pid 786) stopped klogd (pid 789) done Stopping tcf-agent: OK Stopping internet superserver: xinetd. Stopping XServer xinit: connection to X server lost waiting for X server to shut down dbus-daemon[891]: Reloaded configuration (II) Server terminated successfully (0). Closing log file. xinit: unexpected signal 15 stopping statd: done Stopping random number generator daemon. Stopping rpcbind daemon... done. Stopping S.M.A.R.T. daemon: smartd. Deconfiguring network interfaces... done. Stopping watchdog daemon...Sending all processes the TERM signal... Sending all processes the KILL signal... Unmounting remote filesystems... Deactivating swap... Unmounting local filesystems... [ 1835.666980] reboot: Power down