-------------------------------------------------------------------------------- TE0821 TE_XFsbl_HookPsuInit_Custom Configure PLL: SI5338-B Si5338 Init Registers Write. Si5338 Init Complete PLL Status Register 218:0x8 USB Reset Complete ETH Reset Complete -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Xilinx Zynq MP First Stage Boot Loader (TE modified) Release 2021.2 Nov 21 2022 - 08:54:56 Device Name: XCZU2CG -------------------------------------------------------------------------------- TE0821 TE_XFsbl_BoardInit_Custom -------------------------------------------------------------------------------- NOTICE: BL31: v2.4(release):xlnx_rebase_v2.4_2021.1_update1-23-g9188496b9 NOTICE: BL31: Built : 07:41:24, Oct 13 2021 U-Boot 2021.01 (Oct 12 2021 - 09:28:42 +0000) CPU: ZynqMP Silicon: v3 Board: Xilinx ZynqMP DRAM: 4 GiB PMUFW: v1.1 EL Level: EL2 Chip ID: zu2cg NAND: 0 MiB MMC: mmc@ff160000: 0, mmc@ff170000: 1 Loading Environment from FAT... Unable to use mmc 0:0... In: serial Out: serial Err: serial Bootmode: SD_MODE1 Reset reason: EXTERNAL Net: ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 1, interface rgmii-id Warning: ethernet@ff0e0000 (eth0) using random MAC address - b2:c8:95:f2:a5:a8 eth0: ethernet@ff0e0000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found U-Boot script /boot.scr 2710 bytes read in 16 ms (165 KiB/s) ## Executing script at 20000000 Trying to load boot images from mmc1 21451264 bytes read in 1990 ms (10.3 MiB/s) 40869 bytes read in 19 ms (2.1 MiB/s) ## Flattened Device Tree blob at 00100000 Booting using the fdt blob at 0x100000 Loading Device Tree to 000000007dd04000, end 000000007dd10fa4 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.0-xilinx-v2021.2 (oe-user@oe-host) (aarch64-xilinx-linux-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP Tue Oct 12 09:30:57 UTC 2021 [ 0.000000] Machine model: xlnx,zynqmp [ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8') [ 0.000000] printk: bootconsole [cdns0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 512 MiB at 0x000000005dc00000 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000087fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fefffff] [ 0.000000] node 0: [mem 0x0000000800000000-0x000000087fffffff] [ 0.000000] Zeroed struct page in unavailable ranges: 256 pages [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000087fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 22 pages/cpu s49624 r8192 d32296 u90112 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1031940 [ 0.000000] Kernel command line: earlycon console=ttyPS0,115200 clk_ignore_unused root=/dev/mmcblk1p2 rw rootwait cma=512M [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x0000000059c00000-0x000000005dc00000] (64MB) [ 0.000000] Memory: 3501236K/4193280K available (13888K kernel code, 980K rwdata, 3904K rodata, 2048K init, 588K bss, 167756K reserved, 524288K cma-reserved) [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] irq-xilinx: /amba_pl@0/interrupt-controller@80010000: num_irq=32, sw_irq=0, edge=0x0 [ 0.000000] random: get_random_bytes called from start_kernel+0x31c/0x524 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 33.33MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x7b00c47c0, max_idle_ns: 440795202120 ns [ 0.000003] sched_clock: 56 bits at 33MHz, resolution 30ns, wraps every 2199023255541ns [ 0.008249] Console: colour dummy device 80x25 [ 0.012393] Calibrating delay loop (skipped), value calculated using timer frequency.. 66.66 BogoMIPS (lpj=133333) [ 0.022668] pid_max: default: 32768 minimum: 301 [ 0.027382] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.034618] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.043407] rcu: Hierarchical SRCU implementation. [ 0.047374] EFI services will not be available. [ 0.051742] smp: Bringing up secondary CPUs ... [ 0.056515] Detected VIPT I-cache on CPU1 [ 0.056550] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.056611] smp: Brought up 1 node, 2 CPUs [ 0.070675] SMP: Total of 2 processors activated. [ 0.075347] CPU features: detected: 32-bit EL0 Support [ 0.080450] CPU features: detected: CRC32 instructions [ 0.085585] CPU: All CPU(s) started at EL2 [ 0.089628] alternatives: patching kernel code [ 0.095089] devtmpfs: initialized [ 0.101491] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.107015] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.126764] pinctrl core: initialized pinctrl subsystem [ 0.127183] DMI not present or invalid. [ 0.130353] NET: Registered protocol family 16 [ 0.135607] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.141676] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.149480] audit: initializing netlink subsys (disabled) [ 0.154932] audit: type=2000 audit(0.108:1): state=initialized audit_enabled=0 res=1 [ 0.155293] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.169286] ASID allocator initialised with 65536 entries [ 0.174724] Serial: AMBA PL011 UART driver [ 0.199434] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.200490] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.207164] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.213821] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 1.265861] cryptd: max_cpu_qlen set to 1000 [ 1.290057] DRBG: Continuing without Jitter RNG [ 1.369314] raid6: neonx8 gen() 2136 MB/s [ 1.437374] raid6: neonx8 xor() 1599 MB/s [ 1.505449] raid6: neonx4 gen() 2181 MB/s [ 1.573504] raid6: neonx4 xor() 1566 MB/s [ 1.641573] raid6: neonx2 gen() 2076 MB/s [ 1.709629] raid6: neonx2 xor() 1440 MB/s [ 1.777705] raid6: neonx1 gen() 1770 MB/s [ 1.845765] raid6: neonx1 xor() 1219 MB/s [ 1.913831] raid6: int64x8 gen() 1437 MB/s [ 1.981897] raid6: int64x8 xor() 771 MB/s [ 2.049977] raid6: int64x4 gen() 1601 MB/s [ 2.118033] raid6: int64x4 xor() 817 MB/s [ 2.186109] raid6: int64x2 gen() 1398 MB/s [ 2.254166] raid6: int64x2 xor() 747 MB/s [ 2.322238] raid6: int64x1 gen() 1031 MB/s [ 2.390300] raid6: int64x1 xor() 517 MB/s [ 2.390338] raid6: using algorithm neonx4 gen() 2181 MB/s [ 2.394298] raid6: .... xor() 1566 MB/s, rmw enabled [ 2.399229] raid6: using neon recovery algorithm [ 2.404235] iommu: Default domain type: Translated [ 2.408869] SCSI subsystem initialized [ 2.412511] usbcore: registered new interface driver usbfs [ 2.417862] usbcore: registered new interface driver hub [ 2.423127] usbcore: registered new device driver usb [ 2.428171] mc: Linux media interface: v0.10 [ 2.432375] videodev: Linux video capture interface: v2.00 [ 2.437845] EDAC MC: Ver: 3.0.0 [ 2.441294] zynqmp-ipi-mbox mailbox@ff990400: Registered ZynqMP IPI mbox with TX/RX channels. [ 2.449577] FPGA manager framework [ 2.452883] Advanced Linux Sound Architecture Driver Initialized. [ 2.459112] Bluetooth: Core ver 2.22 [ 2.462385] NET: Registered protocol family 31 [ 2.466789] Bluetooth: HCI device and connection manager initialized [ 2.473103] Bluetooth: HCI socket layer initialized [ 2.477945] Bluetooth: L2CAP socket layer initialized [ 2.482969] Bluetooth: SCO socket layer initialized [ 2.488056] clocksource: Switched to clocksource arch_sys_counter [ 2.493985] VFS: Disk quotas dquot_6.6.0 [ 2.497794] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 2.508659] NET: Registered protocol family 2 [ 2.509247] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 2.517435] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 2.525461] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) [ 2.532915] TCP: Hash tables configured (established 32768 bind 32768) [ 2.539078] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 2.545746] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 2.552912] NET: Registered protocol family 1 [ 2.557402] RPC: Registered named UNIX socket transport module. [ 2.562984] RPC: Registered udp transport module. [ 2.567647] RPC: Registered tcp transport module. [ 2.572317] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.579305] PCI: CLS 0 bytes, default 64 [ 2.607793] Initialise system trusted keyrings [ 2.607919] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 2.613693] NFS: Registering the id_resolver key type [ 2.618036] Key type id_resolver registered [ 2.622179] Key type id_legacy registered [ 2.626177] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.632838] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 2.676520] NET: Registered protocol family 38 [ 2.676563] xor: measuring software checksum speed [ 2.684256] 8regs : 2363 MB/sec [ 2.687919] 32regs : 2799 MB/sec [ 2.692870] arm64_neon : 2380 MB/sec [ 2.693056] xor: using function: 32regs (2799 MB/sec) [ 2.698079] Key type asymmetric registered [ 2.702143] Asymmetric key parser 'x509' registered [ 2.707007] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.714341] io scheduler mq-deadline registered [ 2.718837] io scheduler kyber registered [ 2.724556] ps_pcie_dma init() [ 2.750483] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.752197] Serial: AMBA driver [ 2.756186] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 2.764889] brd: module loaded [ 2.768862] loop: module loaded [ 2.769546] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.774296] libphy: Fixed MDIO Bus: probed [ 2.778240] tun: Universal TUN/TAP device driver, 1.6 [ 2.782073] CAN device driver interface [ 2.786420] usbcore: registered new interface driver asix [ 2.791200] usbcore: registered new interface driver ax88179_178a [ 2.797242] usbcore: registered new interface driver cdc_ether [ 2.803035] usbcore: registered new interface driver net1080 [ 2.808652] usbcore: registered new interface driver cdc_subset [ 2.814535] usbcore: registered new interface driver zaurus [ 2.820084] usbcore: registered new interface driver cdc_ncm [ 2.826480] usbcore: registered new interface driver uas [ 2.830986] usbcore: registered new interface driver usb-storage [ 2.837513] rtc_zynqmp ffa60000.rtc: registered as rtc0 [ 2.842130] rtc_zynqmp ffa60000.rtc: setting system clock to 2018-03-09T12:36:39 UTC (1520598999) [ 2.850977] i2c /dev entries driver [ 2.855786] usbcore: registered new interface driver uvcvideo [ 2.860106] USB Video Class driver (1.1.1) [ 2.864625] Bluetooth: HCI UART driver ver 2.3 [ 2.868586] Bluetooth: HCI UART protocol H4 registered [ 2.873684] Bluetooth: HCI UART protocol BCSP registered [ 2.878974] Bluetooth: HCI UART protocol LL registered [ 2.884063] Bluetooth: HCI UART protocol ATH3K registered [ 2.889437] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 2.895684] Bluetooth: HCI UART protocol Intel registered [ 2.901032] Bluetooth: HCI UART protocol QCA registered [ 2.906229] usbcore: registered new interface driver bcm203x [ 2.911852] usbcore: registered new interface driver bpa10x [ 2.917387] usbcore: registered new interface driver bfusb [ 2.922842] usbcore: registered new interface driver btusb [ 2.928297] usbcore: registered new interface driver ath3k [ 2.933791] EDAC MC: ECC not enabled [ 2.937372] EDAC DEVICE0: Giving out device to module edac controller cache_err: DEV edac (POLLED) [ 2.946319] EDAC DEVICE1: Giving out device to module zynqmp-ocm-edac controller zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT) [ 2.958526] sdhci: Secure Digital Host Controller Interface driver [ 2.964421] sdhci: Copyright(c) Pierre Ossman [ 2.968745] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.974687] ledtrig-cpu: registered to indicate activity on CPUs [ 2.980349] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 2.986774] zynqmp_firmware_probe Platform Management API v1.1 [ 2.992536] zynqmp_firmware_probe Trustzone version v1.0 [ 3.045377] securefw securefw: securefw probed [ 3.045627] alg: No test for xilinx-zynqmp-aes (zynqmp-aes) [ 3.049856] zynqmp_aes firmware:zynqmp-firmware:zynqmp-aes: AES Successfully Registered [ 3.057932] alg: No test for xilinx-keccak-384 (zynqmp-keccak-384) [ 3.064104] alg: No test for xilinx-zynqmp-rsa (zynqmp-rsa) [ 3.069604] usbcore: registered new interface driver usbhid [ 3.074981] usbhid: USB HID core driver [ 3.081407] ARM CCI_400_r1 PMU driver probed [ 3.081850] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered [ 3.089845] usbcore: registered new interface driver snd-usb-audio [ 3.096326] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 3.103566] Initializing XFRM netlink socket [ 3.107399] NET: Registered protocol family 10 [ 3.112137] Segment Routing with IPv6 [ 3.115515] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.121586] NET: Registered protocol family 17 [ 3.125681] NET: Registered protocol family 15 [ 3.130087] can: controller area network core [ 3.134431] NET: Registered protocol family 29 [ 3.138815] can: raw protocol [ 3.141756] can: broadcast manager protocol [ 3.145909] can: netlink gateway - max_hops=1 [ 3.150304] Bluetooth: RFCOMM TTY layer initialized [ 3.155088] Bluetooth: RFCOMM socket layer initialized [ 3.160190] Bluetooth: RFCOMM ver 1.11 [ 3.163897] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 3.169174] Bluetooth: BNEP filters: protocol multicast [ 3.174367] Bluetooth: BNEP socket layer initialized [ 3.179295] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 3.185181] Bluetooth: HIDP socket layer initialized [ 3.190219] 9pnet: Installing 9P2000 support [ 3.194360] Key type dns_resolver registered [ 3.198702] registered taskstats version 1 [ 3.202650] Loading compiled-in X.509 certificates [ 3.208403] Btrfs loaded, crc32c=crc32c-generic [ 3.220508] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 48, base_baud = 6249999) is a xuartps [ 3.229529] printk: console [ttyPS0] enabled [ 3.229529] printk: console [ttyPS0] enabled [ 3.233823] printk: bootconsole [cdns0] disabled [ 3.233823] printk: bootconsole [cdns0] disabled [ 3.243125] of-fpga-region fpga-full: FPGA Region probed [ 3.253336] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success [ 3.260518] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success [ 3.267687] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success [ 3.274854] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success [ 3.282022] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success [ 3.289195] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success [ 3.296360] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success [ 3.303534] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success [ 3.310768] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success [ 3.317937] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success [ 3.325101] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success [ 3.332281] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success [ 3.339451] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success [ 3.346619] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success [ 3.353792] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success [ 3.360957] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success [ 3.368914] spi-nor spi0.0: trying to lock already unlocked area [ 3.374918] spi-nor spi0.0: mt25qu512a (131072 Kbytes) [ 3.380084] 4 fixed-partitions partitions found on MTD device spi0.0 [ 3.386429] Creating 4 MTD partitions on "spi0.0": [ 3.391213] 0x000000000000-0x000002000000 : "boot" [ 3.396735] 0x000002000000-0x000002040000 : "bootenv" [ 3.402408] 0x000002040000-0x000004040000 : "kernel" [ 3.407992] 0x000004040000-0x0000040c0000 : "bootscr" [ 3.414108] macb ff0e0000.ethernet: Not enabling partial store and forward [ 3.421532] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM [ 3.428092] xilinx-axipmon fd0b0000.perf-monitor: Probed Xilinx APM [ 3.434635] zynqmp_pll_disable() clock disable failed for dpll_int, ret = -13 [ 3.441840] xilinx-axipmon fd490000.perf-monitor: Probed Xilinx APM [ 3.448384] xilinx-axipmon ffa10000.perf-monitor: Probed Xilinx APM [ 3.472806] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.478298] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 3.486057] xhci-hcd xhci-hcd.1.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x0000000002010010 [ 3.495464] xhci-hcd xhci-hcd.1.auto: irq 84, io mem 0xfe200000 [ 3.501642] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 3.509905] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.517115] usb usb1: Product: xHCI Host Controller [ 3.521984] usb usb1: Manufacturer: Linux 5.10.0-xilinx-v2021.2 xhci-hcd [ 3.528677] usb usb1: SerialNumber: xhci-hcd.1.auto [ 3.533835] hub 1-0:1.0: USB hub found [ 3.537600] hub 1-0:1.0: 1 port detected [ 3.541701] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.547191] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 3.554848] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 3.561403] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.569551] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10 [ 3.577811] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.585029] usb usb2: Product: xHCI Host Controller [ 3.589898] usb usb2: Manufacturer: Linux 5.10.0-xilinx-v2021.2 xhci-hcd [ 3.596593] usb usb2: SerialNumber: xhci-hcd.1.auto [ 3.601710] hub 2-0:1.0: USB hub found [ 3.605474] hub 2-0:1.0: 1 port detected [ 3.610430] at24 0-0050: supply vcc not found, using dummy regulator [ 3.617072] at24 0-0050: 256 byte 24aa025 EEPROM, writable, 1 bytes/write [ 3.623888] cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 39 [ 3.630174] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer with timeout 60s [ 3.637650] cdns-wdt ff150000.watchdog: Xilinx Watchdog Timer with timeout 10s [ 3.647067] macb ff0e0000.ethernet: Not enabling partial store and forward [ 3.655475] libphy: MACB_mii_bus: probed [ 3.659999] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 37 (80:1f:12:f2:b8:ff) [ 3.672467] of_cfs_init [ 3.674921] of_cfs_init: OK [ 3.676071] mmc0: SDHCI controller on ff160000.mmc [ff160000.mmc] using ADMA 64-bit [ 3.677847] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.696067] mmc1: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit [ 3.736812] mmc1: Problem switching card into high-speed mode! [ 3.743228] mmc1: new SDHC card at address 0001 [ 3.748128] mmcblk1: mmc1:0001 SD16G 14.5 GiB [ 3.754161] mmcblk1: p1 p2 [ 3.763651] mmc0: new HS200 MMC card at address 0001 [ 3.772260] mmcblk0: mmc0:0001 IS064G 58.3 GiB [ 3.776971] mmcblk0boot0: mmc0:0001 IS064G partition 1 4.00 MiB [ 3.783093] mmcblk0boot1: mmc0:0001 IS064G partition 2 4.00 MiB [ 3.789088] mmcblk0rpmb: mmc0:0001 IS064G partition 3 4.00 MiB, chardev (245:0) [ 3.820566] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.827094] clk: Not disabling unused clocks [ 3.831551] ALSA device list: [ 3.834516] No soundcards found. [ 3.838199] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.846807] cfg80211: failed to load regulatory.db [ 3.876985] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 3.885095] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 3.892346] devtmpfs: mounted [ 3.895934] Freeing unused kernel memory: 2048K [ 3.900533] Run /sbin/init as init process INIT: version 2.97 booting [ 4.212321] random: fast init done Starting udev [ 5.084167] udevd[243]: starting version 3.2.9 [ 5.131832] random: udevd: uninitialized urandom read (16 bytes read) [ 5.139465] random: udevd: uninitialized urandom read (16 bytes read) [ 5.145932] random: udevd: uninitialized urandom read (16 bytes read) [ 5.241009] udevd[244]: starting eudev-3.2.9 [ 5.464037] zocl: loading out-of-tree module taints kernel. [ 5.471804] [drm] Probing for xlnx,zocl [ 5.475861] zocl-drm a0000000.zyxclmm_drm: IRQ index 32 not found [ 5.482071] [drm] FPGA programming device pcap founded. [ 5.487294] [drm] PR Isolation addr 0x0 [ 5.487827] [drm] Initialized zocl 0.0.0 00000 for a0000000.zyxclmm_drm on minor 0 [ 5.499400] [drm] Probing for xlnx,zocl [ 5.503563] zocl-drm amba_pl@0:zyxclmm_drm: IRQ index 32 not found [ 5.509873] [drm] FPGA programming device pcap founded. [ 5.515095] [drm] PR Isolation addr 0x0 [ 5.515536] [drm] Initialized zocl 0.0.0 00000 for amba_pl@0:zyxclmm_drm on minor 1 [ 6.837679] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null) INIT: Entering runlevel: 5 Configuring network interfaces... udhcpc: started, v1.32.0 udhcpc: sending discover udhcpc: sending discover udhcpc: sending discover udhcpc: sending select for 192.168.13.45 udhcpc: lease of 192.168.13.45 obtained, lease time 3600 /etc/udhcpc.d/50default: Adding DNS 147.231.12.1 /etc/udhcpc.d/50default: Adding DNS 147.231.10.9 /etc/udhcpc.d/50default: Adding DNS 8.8.8.8 done. Starting system message bus: dbus. Starting random number generator daemon. Starting haveged: haveged: command socket is listening at fd 3 haveged: haveged starting up haveged: haveged: ver: 1.9.13; arch: generic; vend: ; build: (gcc 10.2.0 CTV); collect: 128K haveged: haveged: cpu: (VC); data: 16K (D); inst: 16K (D); idx: 11/40; sz: 15456/64452 haveged: haveged: tot tests(BA8): A:1/1 B:1/1 continuous tests(B): last entropy estimate 7.9999 haveged: haveged: fills: 0, generated: 0 Starting OpenBSD Secure Shell server: sshd done. Starting Xserver Starting rpcbind daemon... done. starting statd: done starting Busybox HTTP Daemon: httpd... done. X.Org X Server 1.20.9 X Protocol Version 11, Revision 0 Build Operating System: Linux Current Operating System: Linux petalinux 5.10.0-xilinx-v2021.2 #1 SMP Tue Oct 12 09:30:57 UTC 2021 aarch64 Kernel command line: earlycon console=ttyPS0,115200 clk_ignore_unused root=/dev/mmcblk1p2 rw rootwait cma=512M Build Date: 25 August 2020 03:40:19PM Current version of pixman: 0.40.0 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Fri Mar 9 12:36:53 2018 (==) Using config file: "/etc/X11/xorg.conf" (==) Using system config directory "/usr/share/X11/xorg.conf.d" (EE) Fatal server error: (EE) no screens found(EE) (EE) Please consult the The X.Org Foundation support at http://wiki.x.org for help. (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information. (EE) (EE) Server terminated with error (1). Closing log file. Starting internet superserver: inetd. NFS daemon support not enabled in kernel Init Start mount: /mnt/BOOT: special device /dev/disk/by-label/BOOT does not exist. Init End Starting syslogd/klogd: done Starting internet superserver: xinetd. Starting watchdog daemon...done Starting tcf-agent: OK PetaLinux 2021.2 petalinux ttyPS0 root@petalinux:~# ifconfigxinit: giving up xinit: unable to connect to X server: Connection refused xinit: server error root@petalinux:~# ifconfig eth0 Link encap:Ethernet HWaddr 80:1F:12:F2:B8:FF inet addr:192.168.13.45 Bcast:192.168.13.255 Mask:255.255.255.0 inet6 addr: fe80::821f:12ff:fef2:b8ff/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:43 errors:0 dropped:0 overruns:0 frame:0 TX packets:18 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6016 (5.8 KiB) TX bytes:2844 (2.7 KiB) Interrupt:37 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:380 (380.0 B) TX bytes:380 (380.0 B) root@petalinux:~# cd /media/sd-mmcblk1p1 root@petalinux:/media/sd-mmcblk1p1# ls BOOT.BIN Image boot.scr krnl_vadd.xclbin system.dtb test_vadd root@petalinux:/media/sd-mmcblk1p1# ./test_vadd krnl_vadd.xclbin INFO: Reading krnl_vadd.xclbin Loading: 'krnl_vadd.xclbin' Trying to program device[0]: edge Device[0]: program successful! TEST PASSED root@petalinux:/media/sd-mmcblk1p1# halt Broadcast message from root@▒ Rk▒▒+▒▒▒▒ ▒▒KҮ▒.]Y[▒▒alt NOW! INIT: Sending processes configured via /etc/inittab the TERM signal root@petalinux:/media/sd-mmcblk1p1# Stopping haveged: Stopping OpenBSD Secure Shell server: sshdstopped /usr/sbin/sshd (pid 667) . stopping Busybox HTTP Daemon: httpd... stopped httpd (pid 696) done. Stopping system message bus: dbus. Stopping internet superserver: inetd. stopping mountd: done stopping nfsd: done Stop. Stopping syslogd/klogd: stopped syslogd (pid 710) stopped klogd (pid 713) done Stopping tcf-agent: OK Stopping internet superserver: xinetd. Stopping XServer stopping statd: done Stopping random number generator daemon. Stopping rpcbind daemon... done. Stopping S.M.A.R.T. daemon: smartd. Deconfiguring network interfaces... done. Stopping watchdog daemon...Sending all processes the TERM signal... logout Sending all processes the KILL signal... Unmounting remote filesystems... Deactivating swap... Unmounting local filesystems... [ 133.484301] reboot: Power down