Versions Compared

Old Version 23

changes.mady.by.user Sergio Pavesi

Saved on

compared with

New Version 24

changes.mady.by.user Sergio Pavesi

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

  • When slide switch S2 is in the left position (FX2 PON = power rails conditionally on depending on signal FX2_PS_EN), signal PS_EN is set to signal FX2_PS_EN driven by the EZ-USB FX2LP USB FX2 microcontroller under user control.

    Figure 34: Slide switch S2 schematic.


    Figure 35: When slide switch S2 = FX2 PON, signal PS_EN is set to signal FX2_PS_EN driven by the EZ-USB FX2LP USB FX2 microcontroller under user control.
     

    Slide Switch S2 = FX2 PON

     

    When slide switch S2 is in the left position ( = FX2 PON : power rails conditionally on depending on signal FX2_PS_EN), signal PS_EN is set to signal FX2_PS_EN driven by the EZ-USB FX2LP USB FX2 microcontroller under user control.

     

    Image Added

     

    Figure 35: S2 on position FX2 PON (PS_EN = FX2_PS_EN = x ).

     
    1. Dynamic full power operation (PS_EN = high): when the EZ-USB FX2LP USB FX2 microcontroller sets signal PS_EN = FX2_PS_EN = high, power rails 2.5V and 1.2V are enabled.
      This setting can be useful for .
    2. Dynamic low power operation (PS_EN = low): when the EZ-USB FX2LP USB FX2 microcontroller resets signal PS_EN = FX2_PS_EN = low, the following components are switched off:
     
    • FPGA core logic (1.2V)
    • DDR SDRAM (2.5V)
    • FPGA bank 3 (2.5V)
    • VREF (2.5V)
    • VCCCIO0 (2.5V) FPGA bank 0
     

    Slide Switch S2 = PON 

     

    Full power operation ((PS_EN = high): when slide switch S2 is in the right position (PON = power rails unconditionally on), signal PS_EN is set to power rail 3.3V. Thus power rails 2.5V and 1.2V are unconditionally enabled.

    Image Added
    Figure 34: S2 on position PON.


  • Signal PS_EN enables (high) or disables (low) power rails 2.5V and 1.2V.

    Figure 36: Power rails 2.5V and 1.2V could be enabled/disabled by signal PS_EN.
  • According to the corresponding assembly option, power rail VCCCIO0 can depend or not on the 2.5V power rail.

    Figure 37: example of VCCIO0 assembly not dependent on 2.5V power rail. The other way is also possible.

  • Power-rail 3.3V is not controlled by signal PS_EN and is unconditionally enabled. 
      
    Figure 38: Power rails 3.3V could not be enabled/disabled by signal PS_EN.

Table 14 summarizes all switching options implied by slide switch S2 and firmware signal FX2_PS_EN (under the standard assembly option).

power rail

S2= PON


(Full power)

S2 = FX2 PON and
PS_EN = FX2_PS_EN = 1

(Dynamic full power)

S2 = FX2 PON and
PS_EN = FX2_PS_EN = 0

(Dynamic low power)

1.2V

on

on

off

2.5V

on

on

off

VCCCIO0 (= 2.5V)
R131+R132- assembly (21)

on

on

off

VCCCIO0 (= 3.3V)
R131-R132+ assembly (32)

on

on

on

(2) R131 soldered / R132 unsoldered

(3) R131 unsoldered / R132 soldered

Table 14: Slide switch S2 settings overview ( 1.2V , 2.5V, VCCIO0).

Slide Switch S2 = FX2 PON

When slide switch S2 is in the left position ( = FX2 PON : power rails conditionally on depending on signal FX2_PS_EN), signal PS_EN is set to signal FX2_PS_EN driven by the EZ-USB FX2LP USB FX2 microcontroller under user control.

Image Removed

Figure 35: S2 on position FX2 PON (PS_EN = FX2_PS_EN = x ).

...

)

...

.

...

...

 

...

When slide switch S2 is in the right position (PON = power rails unconditionally on), signal PS_EN is set to power rail 3.3V. Thus power rails 2.5V and 1.2V are unconditionally enabled.

...