Page History
...
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
- (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
- (6) REV03 select correct SDIO voltage by jumper. REV02 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).
- (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage
TEB0707
ETH | SD Card | USB Host | HS CA(15) | HS CB(15) | HS CC(15) | LS CA(16) | User LEDs(17) | USB UART | USB JTAG | |
---|---|---|---|---|---|---|---|---|---|---|
TE0710 | , 3.3V B16 I/O | |||||||||
TE0711 | , 1.8V B16 I/O | |||||||||
TE0712 | 100 MBit | , 1.8V B13 I/O | , some fix 3.3V B14 I/O | |||||||
TE0713 | (19) | |||||||||
TE0715-15 | (3x PL, 3x PS) | |||||||||
TE0715-30 (2) | , max 1.8V | , max 1.8V | (3x PL, 3x PS) | |||||||
TE0720 | (3x PL, 3x PS) | |||||||||
TE0741 (4) | , MGTs | (18) | ||||||||
TE0820 (2) | (6) | , max 1.8V | , max 1.8V | , max 1.8V | (3x PL, 3x PS) | |||||
TE0821 (2) | (6) | , max 1.8V | (3x PL, 3x PS) | |||||||
TE0823 (2) | (6) | , max 1.8V | , max 1.8V | , max 1.8V | (3x PL, 3x PS) | |||||
TE0841 (2)(3) | , MGTs | , max 1.8V | , max 1.8V | (3x PL, 3x PS) |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes connected to SD-Level shifter: TEB0707 - Leave J4 open.
- (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
- (6) Select correct SDIO voltage by jumper.
- (15) Fix 3.3V signals of CRUVI HS connectors are connected to MAX10 CPLD and can be used firmware dependent (In standard firmware not implemented).
- (16) Signals on CRUVI LS connector are connected to MAX10 CPLD and can be used firmware dependent (In standard firmware 4 input and 4 output).
- (17) LEDs are connected to MAX10 CPLD and can be used firmware dependent (In standard Firmware implemented.)
- (18) Not available on assembly variants with K70T.
- (19) Two diff. pairs connected to FT600 USB3 lanes. Other signals usable.
TEBA0841
SFP | USB Host | SD Card "J4 2x5 Pin Header(2.54)" | GPIO | XMOD (JTAG/UART) "JX1 2x6 Pin Header (2.54)" | GPIO (JTAG/UART/MGT REFCLK) "J3 2x8 Pin Header(2.54)" | |
---|---|---|---|---|---|---|
TE0710 | ,3.3V B16 I/O | (9) | (8) | |||
TE0711 | , device only(14) | ,1.8V B16 I/O | (9) | , B34 CLK input | ||
TE0712 | , B13 I/O | (9) | , B34 CLK input | |||
TE0713 | , device only(14) | , B13 I/O | (9) | |||
TE0715 (10) | (7) | (9) | ||||
TE0715-30 (10) | (7) | (9) | ||||
TE0720 (10) | (7) | (9) | , B34 CLK input | |||
TE0741 (11) | ,MGT's | (9) | ||||
TE0820 (10) | (6) | (9) | ||||
TE0821 (10) | (6) | (9) | ||||
TE0823 (10) | (6) | (9) | ||||
TE0841 | ,MGT's | (9) |
...
Overview
Content Tools