...
The Trenz Electronic TEB0835 is a carrier for TE0835 module which is based on Xilinx UltraScale+ RFSoC. The Carrier is equipped with a Micro SD card reader, Micro USB2.0, se21x UMCC connectors and 6x SMD connectors for clocks and ADC/DAC inputs/outputs , 6x Green User LEDs, Reset Push Button, DIP Switch for Mode, Battery Holder, FT2232H FTDI, programmable clock generators and a Temperature sensor IC.
Refer to http://trenz.org/teb0835-info for the current online version of this manual and other available documentation.
...
- Modules:
- RAM/Storage
- On Board
- Programmable Clock Generator
- I2C Switch IC
- 9x 6x User Green LEDs
- 16x RF Transformation
- Reset Push Button
- Temperature Sensor
- FT2232H FTDI
- SDIO Port Expander
- DIP Switch
- Interface
- 10x UMCC Connectors
- 6x SMA Connectors
- 2x Micro USB2.0
- Micro SD Card Socket
- 2x UEC5 Connectors
- 2x UCC8 Connectors
- PCIe x8 Card
- 2x Samtec Razor Beam SS5 (2x80 pol) Board to Board Connectors
- Power
- Dimension
...
Micro USB2.0
There is a Micro USB2.0 port J30, provided for user.
Scroll Title |
---|
anchor | Table_SIP_MicroUSB2 |
---|
title | Micro USB2.0 Socket connections |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J30
| USB_N/USB_P | B2B, J17 | Data | USB0_VBUS | B2B, J17 | VBUS | USB0_ID | B2B, J17 | ID |
|
SMA Connectors
Micro SD Card Reader
There is a Micro SD Card socket J28 connected to B2B J17 through an I/O expander U11There are 6 SMA Connectors provided for Analog and Digital signals.
Scroll Title |
---|
anchor | Table_SIP_SMAMicroSD |
---|
title | SMA Connectors informationMicro SD Card Socket connections |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
DesignatorPin | Signal Name | Connected to | Note |
---|
J1ADC0IN J18J17 | connected to IO expander | CMD | SD_CMD |
J3 | ADC2_IN J18J5 | ADC4_INJ17 | connected to IO expander | CLK | SD_CLK | B2B, | J18J7 | ADC6_IN | B2B, J18 | J9 | DAC0_OUT | B2B, J18 | J11 | DAC2_OUT | B2B, J18 | |
UMCC Connectors
J17 | connected to IO expander | DATA0...3 | SD_DATA0...3 | B2B, J17 | connected to IO expander | CD | SD_CD | B2B, J17 |
|
|
SMA Connectors
There are 6 SMA There are 8 UMCC Connectors provided for Analog and Digital signals input and output.
Scroll Title |
---|
anchor | Table_SIP_UMCCSMA |
---|
title | UMCC SMA Connectors information |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J2J1 | ADC1ADC0_IN | B2B, J18 |
| J4J3 | ADC3ADC2_IN | B2B, J18 |
| J6J5 | ADC5ADC4_IN | B2B, J18 |
| J8J7 | ADC7ADC6_IN | B2B, J18 |
| J10J9 | DAC1DAC0_OUT | B2B, J18 |
| J12J11 | DAC3DAC2_OUT | B2B, J18 | J13 | DAC4_OUT | B2B, J18 | J14 | DAC5_OUT | B2B, J18 | J15 | DAC6_OUT | B2B, J18 | J16 | DAC7_OUT | B2B, J18 |
|
UCE5 Connectors
The TEB0835 is equipped with two UCE5 Connectors.
UMCC Connectors
There are 8 UMCC Connectors provided for Analog and Digital signals input and output.
Scroll Title |
---|
anchor | Table_SIP_UMCC |
---|
title | UMCC |
---|
|
Scroll Title |
---|
anchor | Table_SIP_UEC5 |
---|
title | UEC5 Connectors |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J22J2 | B128_TX0...3ADC1_IN | B2B, J17 | 8x Single Ended/ 4x LVDS Pairs | J18 |
| J4 | ADC3_INB128_RX0...3 | B2B, J17 | 8x Single Ended/ 4x LVDS Pairs | J24 | J18 |
| J6 | ADC5_INB129_TX0...3 | B2B, J17 | 8x Single Ended/ 4x LVDS Pairs | J18 |
| J8 | ADC7_INB129_RX0...3 | B2B, J17 | 8x Single Ended/ 4x LVDS Pairs |
|
UCC8 Connectors
The TEB0835 is equipped with two UCC8 Connectors.
J18 |
| J10 | DAC1_OUT | B2B, J18 |
| J12 | DAC3_OUT | B2B, J18 |
| J13 | DAC4_OUT | B2B, J18 |
| J14 | DAC5_OUT | B2B, J18 |
| J15 | DAC6_OUT | B2B, J18 |
| J16 | DAC7_OUT | B2B, J18 |
|
|
UCE5 Connectors
The TEB0835 is equipped with two UCE5 Connectors.
Scroll Title |
---|
anchor | Table_SIP_UEC5 |
---|
title | UEC5 Connectors |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection |
---|
|
|
Scroll Title |
---|
anchor | Table_SIP_UCC8 |
---|
title | UCC8 Connectors |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J23FFA_MPRSFFA_MSEL | B2B, J17 | FFA_INTL | 8x Single Ended/ 4x LVDS Pairs | B128_RX0...3 | B2B, J17 | 8x Single Ended/ 4x LVDS Pairs | J24 | B129_TX0...3 | B2B, J17 | FFA_RSTL8x Single Ended/ 4x LVDS Pairs | B129_RX0...3 | B2B, J17 |
FFA_SCL/FFA_SDA | I2C Switch, U7 | J25 | FFB_MPRS | B2B, J17 | FFB_MSEL | B2B, J17 | FFB_INTL | B2B, J17 | FFB_RSTL | B2B, J17 | FFB_SCL/FFB_SDA | I2C Switch, U7 | |
PCIe Card
There is a PICe-8x-Kurz card provided on the TEB0835 board.
8x Single Ended/ 4x LVDS Pairs |
|
UCC8 Connectors
The TEB0835 is equipped with two UCC8 Connectors.
Scroll Title |
---|
anchor | Table_SIP_UCC8 |
---|
title | UCC8 |
---|
|
Scroll Title |
---|
anchor | Table_SIP_PCIe |
---|
title | PCIe-x8-Kurz Connectors |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J23 | B505_RX0...38x Single Ended/ 4x LVDS Pairs | B505_TX0...38x Single Ended/ 4x LVDS Pairs | EXT_CLKIN_PSMGTPCIE_RSTB_R
| FFA_SCL/FFA_SDA | I2C Switch, U7 |
| J25 | FFB_MPRS | B2B, J17 |
Pulled up to 1.8V | |
Test Points
| FFB_MSEL | B2B, J17 |
| FFB_INTL | B2B, J17 |
| FFB_RSTL | B2B, J17 |
| FFB_SCL/FFB_SDA | I2C Switch, U7 |
|
|
PCIe Card
There is a PICe-8x-Kurz card provided on the TEB0835 board.
Page properties |
---|
|
you must fill the table below with group of Test Point which are indicated as TP in a schematic. If there is no Test Point remarked in the schematic, delet the Test Point section.
Example:
Test Point | Signal | B2B | Notes |
---|
10 | PWR_PL_OK | J2-120 | Scroll Title |
---|
anchor | Table_SIP_TPsPCIe |
---|
title | Test Points InformationPCIe-x8-Kurz Connectors |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Test Point | Notes | TP1 | 5V | B2B, J17 | TP2GND | GND | TP4 | ADC0_VCM J18J17 | 8x Single Ended/ 4x LVDS Pairs | B505_TX0...3 |
TP5 | ADC1_VCM J18TP6 | USB_VBUS | Micro USB2.0, J29 | J17 | 8x Single Ended/ 4x LVDS Pairs | EXT_CLKIN_PSMGT |
TP7 | UART0_RXTP8 | UART0_TXTP9 | ADC2_VCM | B2B, J18 | TP10 | ADC3_VCM | B2B, J18 | TP11 | ADC4_VCM | B2B, J18 | TP12 | ADC5_VCM | B2B, J18 | TP13 | ADC6_VCM | B2B, J18 | TP14 | ADC7_VCM | B2B, J18 | |
On-board Peripherals
Page properties |
---|
|
Notes : - add subsection for every component which is important for design, for example:
- Two 100 Mbit Ethernet Transciever PHY
- USB PHY
- Programmable Clock Generator
- Oscillators
- eMMCs
- RTC
- FTDI
- ...
- DIP-Switches
- Buttons
- LEDs
|
Page properties |
---|
|
Notes : In the on-board peripheral table "chip/Interface" must be linked to the corresponding chapter or subsection |
...
anchor | Table_OBP |
---|
title | On board peripherals |
---|
...
Test Points
Page properties |
---|
|
you must fill the table below with group of Test Point which are indicated as TP in a schematic. If there is no Test Point remarked in the schematic, delet the Test Point section. Example: Test Point | Signal | B2B | Notes |
---|
10 | PWR_PL_OK | J2-120 |
|
|
Scroll Title |
---|
anchor | Table_SIP_TPs |
---|
title | Test Points Information |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Test Point | Signal | Connected to | Notes |
---|
TP1 | 5V | B2B, J17 |
| TP2...3 | GND | GND |
| TP4 | ADC0_VCM | B2B, J18 |
| TP5 | ADC1_VCM | B2B, J18 |
| TP6 | USB_VBUS | Micro USB2.0, J29 |
| TP7 | UART0_RX | B2B, J17 |
| TP8 | UART0_TX | B2B, J17 |
| TP9 | ADC2_VCM | B2B, J18 |
| TP10 | ADC3_VCM | B2B, J18 |
| TP11 | ADC4_VCM | B2B, J18 |
| TP12 | ADC5_VCM | B2B, J18 |
| TP13 | ADC6_VCM | B2B, J18 |
| TP14 | ADC7_VCM | B2B, J18 |
|
|
On-board Peripherals
Page properties |
---|
|
Notes : - add subsection for every component which is important for design, for example:
- Two 100 Mbit Ethernet Transciever PHY
- USB PHY
- Programmable Clock Generator
- Oscillators
- eMMCs
- RTC
- FTDI
- ...
- DIP-Switches
- Buttons
- LEDs
|
Page properties |
---|
|
Notes : In the on-board peripheral table "chip/Interface" must be linked to the corresponding chapter or subsection |
...
Scroll Title |
---|
anchor | Table_OBP_EEP |
---|
title | I2C EEPROM interface MIOs and pins |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | widths | sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
Pin | Schematic | Connected to | Notes |
---|
CS | EECS | FTDI, U12 | CLK | EECLK | FTDI, U12 | DIN | EEDATA | FTDI, U12 | Scroll Title |
---|
anchor | Table_OBP_I2C_EEPROM |
---|
title | I2C address for EEPROMOn board peripherals |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
I2C AddressChip/Interface | Designator | Notes |
---|
A0 |
...
The FTDI chip U12 converts signals from USB2 to a variety of standard serial and parallel interfaces. Refer to the FTDI data sheet to get information about the capacity of the FT2232H chip. FTDI FT2232H chip is used in MPPSE mode for JTAG, 2 I/O's of Channel B are routed to B2B J17 and must be used as UART.
...
EEPROM
Scroll Title |
---|
anchor | Table_OBP_FTDIEEP |
---|
title | FTDI chip interfaces I2C EEPROM interface MIOs and pins |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
FTDI Chip U12 Signal NameADBUS0JTAG_TCKB2B J17JTAG interfaceADBUS1 | JTAG_TDI | B2B, J17 | ADBUS2 | JTAG_TDO | B2B, J17 | ADBUS3 | JTAG_TMS | B2B, J17 | BDBUS0 | UART0_RX | B2B, J17 | UART | BDBUS1 | UART0_TX | B2B, J17 | UART | EECS/EECLK/EEDATA | BDBUS2 | EEPROM, U15 | FTDI configuration | DM/DP | D_N/D_P | Micro USB2.0, J29 | FTDI Input | |
LEDs
EECLK | FTDI, U12 |
| DIN | EEDATA | FTDI, U12 |
|
|
Scroll Title |
---|
anchor | Table_OBP_I2C_EEPROM |
---|
title | I2C address for EEPROM |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths |
---|
|
|
Scroll Title |
---|
anchor | Table_OBP_LED |
---|
title | On-board LEDs |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
ColorConnected toActive LevelNote | D1 | Green | PG_1.8V | High | D2 | Green | PG_3.3V | High | D3 | Green | PG_5V | High | D6...11 | Green | B2B, J18 | High | |
...
FTDI
The FTDI chip U12 converts signals from USB2 to a variety of standard serial and parallel interfaces. Refer to the FTDI data sheet to get information about the capacity of the FT2232H chip. FTDI FT2232H chip is used in MPPSE mode for JTAG, 2 I/O's of Channel B are routed to B2B J17 and must be used as UART.
The configuration of FTDI FT2232H chip is pre-programmed on the EEPROM U9.
Scroll Title |
---|
anchor | Table_OBP_FTDI |
---|
title | FTDI chip interfaces and pins |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
FTDI Chip U12 Pin | Signal Schematic Name | Connected to | Notes |
---|
ADBUS0 | JTAG_TCK | B2B, J17 | JTAG interface | ADBUS1 | JTAG_TDI | B2B, J17 | ADBUS2 | JTAG_TDO | B2B, J17 | ADBUS3 | JTAG_TMS | B2B, J17 | BDBUS0 | UART0_RX | B2B, J17 | UART | BDBUS1 | UART0_TX | B2B, J17 | UART | EECS/EECLK/EEDATA | BDBUS2 | EEPROM, U15 | FTDI configuration | DM/DP | D_N/D_P | Micro USB2.0, J29 | FTDI Input |
|
LEDs
Scroll Title |
---|
anchor | Table_OBP_LED |
---|
title | On-board LEDs |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Color | Connected to | Active Level | Note |
---|
D1 | Green | PG_1.8V | High |
| D2 | Green | PG_3.3V | High |
| D3 | Green | PG_5V | High |
| D6...11 | Green | B2B, J18 | High |
|
|
Clock Sources
Scroll Title |
---|
anchor | Table_OBP_CLK |
---|
title | Osillators |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Description | Frequency | Note |
---|
U6 | MEMS Oscillator | 100 MHz |
| U16 | MEMS Oscillator | 12 MHz |
| Y1 | Crystal Oscillator | 54 MHz |
| U5 | PLL Clock Generator | Variable |
|
|
Programmable Clock Generator
There is a programmable clock generator on-board (U5) provided in order to generate variable clocks for the module. Programming can be done using I2C via PIN header J20. The I2C Address is 0x68.
Scroll Title |
---|
anchor | Table_OBP_CLKPCLK |
---|
title | OsillatorsProgrammable Clock Generator Inputs and Outputs |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default | style |
---|
widths | sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
U5 Pin
| Signal | Connected to | Direction |
---|
Designator | Description | Frequency | Note |
---|
IN0 | CLKIN0 | Oscillator, U6 |
MEMS Oscillator | 100 MHz | U16 | MEMS Oscillator | 12 MHz | Y1 | Crystal Oscillator | 54 MHz | U5 | PLL Clock Generator | Variable | |
Programmable Clock Generator
There is a programmable clock generator on-board (U5) provided in order to generate variable clocks for the module. Programming can be done using I2C via PIN header J20. The I2C Address is 0x68.
| Input |
| IN1 | CLKIN1 | UMCC Connector, J36 | Input |
| IN2 | CLKIN2 | UMCC Connector, J37 | Input |
| IN3 | FB | Programmable Clock Generator, U5 | Input/Output |
| XA/XB | CLK0_XA/XB | Oscillator, Y1 | Input |
| IN_SEL0...1 | DSPLL0_SEL0...1 | I2C Switch, U7 DIP Switch, S2 | Input |
| nINTR | DSPLL0_INTR_N | I2C Switch, U7 | Input |
| nLOL | DSPLL0_LOL_N | Green LED, D12 | Input |
| nRST | DSPLL0_RST_N | 1.8 V | Input |
| SCLK | DSPLL0_SCL | I2C Switch, U7 | Input |
| SDA/SDIO | DSPLL0_SDA | I2C Switch, U7 Pin Header, J41 | In/Out |
| INTR | PLL_INTR_N | B2B, J17 | Output |
| OUT0A | CLKOUT0A | B2B, J17 | Output |
| OUT0 | CLKOUT0_P | B2B, J17 | Output |
| OUT1 | PLLCLK1 | UMMC, J27 | Output |
| OUT2 | PLLCLK2 | UMMC, J20 | Output |
| OUT3 | PLLCLK3 | UMMC, J32 | Output |
| OUT4 | PLLCLK4 | UMMC, J33 | Output |
| OUT5 | PLLCLK5 | UMMC, J34 | Output |
| OUT6 | PLLCLK6 | UMMC, J35 | Output |
| OUT7 | CLKOUT7 | UMMC, J38 | Output |
| OUT8 | CLKOUT8 | UMMC, J42 | Output |
| OUT9 | CLKOUT9 | UMMC, J43 | Output |
| OUT9A | CLKOUT9A | Programmable Clo0ck Generator, U5 |
|
Scroll Title |
---|
anchor | Table_OBP_PCLK |
---|
title | Programmable Clock Generator Inputs and Outputs |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
U5 Pin
| Signal | Connected to | Direction | Note |
---|
IN0 | CLKIN0 | Oscillator, U6 | Input | IN1 | CLKIN1 | UMCC Connector, J36 | Input | IN2 | CLKIN2 | UMCC Connector, J37 | Input | IN3 | FB | Programmable Clock Generator, U5 | Input/Output | XA/XB | CLK0_XA/XB | Oscillator, Y1 | Input | SCL | PLL_SCL | B2B, J17 | Input | SDA | PLL_SDA | B2B, J17 | In/Out | INTR | PLL_INTR_N | B2B, J17 | Output | CLK1 | B129_CLK1 | B2B, J17 | Output | CLK2 | B128_CLK1 | B2B, J17 | Output |
|
|
Power and Power-On Sequence
...