TE0630 is provided with a Dip switch S1B.
Dip switch S1B conditions the value of signal PS_EN.
In this way, S1B conditionally/unconditionally enables the power rails 1.2 V, 1.5 V and 2.5 V.
Please note the 4 switch labels are on one side and the <ON> label is on the opposite side.
DIP slide switches S1[A:D] condition the value of some system signals as described in the table below.
Scroll pdf title |
---|
title | Dip switch S1[A:D]. The switch S1B is the one with label 2 and B |
---|
|
|
Scroll pdf title |
---|
title | Dip switch S1B schematic. |
---|
|
|
Scroll pdf title |
---|
title | When S1B = FX2 PON, PS_EN=FX2_PS_EN |
---|
|
|
When S1B is turned off (FX2 PON position), the 1.2 V, 1.5 V and 2.5 V power rails are controlled by the USB (EZ-USB FX2LP USB FX2) microcontroller. At start-up, the USB microcontroller switches off the power rails 1.2 V, 1.5 V and 2.5 V and starts up the module in low-power mode. After enumeration, the USB microcontroller firmware enables (switches on) the power rails 1.2 V, 1.5 V and 2.5 V, if enough current is available from the USB bus.
When S1B is turned on (PON position), the power rails 1.2 V, 1.5 V and 2.5 V are always enabled (switched on).
Scroll pdf title |
---|
title | Dip switch S1B settings overview (power rails 1.2 V, 1.5V and 2.5 V only). |
---|
|
| | |
---|
FX2 PON (off) | | Power rails 1.2 V, 1.5 V and 2.5 V controlled by USB FX2 microcontroller (signal FX2_PS_EN) PS_EN = FX2_PS_EN = 1 or 0 | PON (on) | | Power rails 1.2 V, 1.5 V and 2.5 V always enabled (PS_EN = 1) PS_EN ≠ FX_PS_EN = 1 or 0
|
|
Signal FX2_PS_EN
To command signal FX2_PS_EN, read the reference firmware code.
IOD = 0x03; // Enable PS_EN and disable PROG_B
OED = 0x03; // Configure PS_EN and PROG as outputs
Scroll pdf title |
---|
title | Table from EZ-USB(R) Technical Reference Manual (EZ-USB_TRM.pdf). |
---|
|
Table from EZ-USB(R) Technical Reference Manual (EZ-USB_TRM.pdf) | | | |
---|
PD[7:0] | FD[15:8] | IFCFG1 = 1 and any WORDWIIDE bit = 1 | Slave FIFOs chapter 9 on page 99 |
|
Signal PS_EN
Signal PS_EN enables (1) or disables (0) power rails 1.2 V, 1.5 V and 2.5 V.
Scroll pdf title |
---|
title | Power rails 1.2 V, 1.5 V and 2.5 V could be enabled/disabled by signal PS_EN. |
---|
|
|
Power-rail 3.3V is not controlled by signal PS_EN and is unconditionally enabled.
Scroll pdf title |
---|
title | Power rails 3.3V could not be enabled/disabled by signal PS_EN. |
---|
|
|
VCCIO assembly options
Info |
---|
According to the corresponding assembly option, power rail VCCCIO0 (enabled by PS_EN and switch S1B ) can depend or not on the power rail 2.5V. |
See section "FPGA I/O banks power supply" here.
Dip Switch S1B = FX2 PON
When Dip switch S1B is in the left position ( = FX2 PON : power rails conditionally on depending on signal FX2_PS_EN), signal PS_EN is set to signal FX2_PS_EN (PS_EN = FX2_PS_EN) driven by the EZ-USB FX2LP USB FX2 microcontroller under user control (IOD and OED of fw.c).
Scroll pdf title |
---|
title | S1B on position FX2 PON (PS_EN = FX2_PS_EN = 1 or 0 ). |
---|
|
|
- Dynamic full power operation (PS_EN = 1): when the EZ-USB FX2LP USB FX2 microcontroller sets signal PS_EN = FX2_PS_EN = high, power rails 1.2 V, 1.5 V and 2.5 V are enabled.
This setting can be useful for . - Dynamic low power operation (PS_EN = 0): when the EZ-USB FX2LP USB FX2 microcontroller resets signal PS_EN = FX2_PS_EN = low, the following components are switched off:
- FPGA core logic (1.2 V)
- DDR SDRAM (2.5 V)
- FPGA bank 1 (1.5 V)
- VREF1 (0.75 V)
- VCCCIO0 (2.5 V) FPGA bank 0 (if R102+R103- assembly)
Dip Switch S1B = PON
Full power operation (PS_EN = 1): when Dip switch S1B is in the right position (PON = power rails unconditionally on), signal PS_EN is set to power rail 3.3V. Thus power rails 1.2 V, 1.5 V and 2.5 V are unconditionally enabled.
Scroll pdf title |
---|
title | S1B on position PON (PS_EN ≠ FX2_PS_EN = x; PS_EN = high ). |
---|
|
|
Summary table
The table below summarizes all switching options implied by Dip switch S1B and firmware signal FX2_PS_EN (under the standard assembly option).
Scroll pdf title |
---|
title | Dip switch S1B settings overview ( 1.2 V, 1.5 V , 2.5 V, VCCIO0). |
---|
|
| | | |
---|
1.2 V | on | on | off | 1.5 V | on | on | off | 2.5 V | on | on | off | VCCCIO0 (= 2.5 V) R102-R103+ assembly (1) | on | on | off | VCCCIO0 (= 3.3 V) R102+R103- assembly (2) | on | on | on |
(1) R102 unpopulated / R103 populated (2) R102 populated / R103 unpopulated |