Page History

Design Name always "TE Series Name" + Design name, for example "TEI0006 Test Board"

Important General Note:

• Export PDF to download, if quartus revision is changed!

• Designate all graphics and pictures with a number and a description, Use "Scroll Title" macro

  • Use "Scroll Title" macro for pictures and table labels. Figure number must be set manually at the moment (automatically enumeration is planned by scrollPDF)

    • Figure template (note: inner scroll ignore/only only with drawIO object):

      Scroll Title
      anchor Figure_xyz title Text
      Scroll Ignore Create DrawIO object here: Attention if you copy from other page, use Scroll Only image link to the generate DrawIO PNG file of this page. This is a workaround until scroll pdf export bug is fixed

      
      

    • Table template:

      • Layout macro can be use for landscape of large tables
      • Set column width manually(can be used for small tables to fit over whole page) or leave empty (automatically)

    • 
      

      Scroll Title
      anchor Table_xyz title Text
      Scroll Table Layout orientation portrait sortDirection ASC repeatTableHeaders default style widths sortByColumn 1 sortEnabled false cellHighlighting true Example Comment 1 2

      
      

• ...

Notes :

• short description of the design

• Short Link of "Scroll only" macro:

  • Use short link the Wiki Resource page, for example: http://trenz.org/tei0006-info

  • List of available short links: https://wiki.trenz-electronic.de/display/CON/Redirects

Notes :

• Add basic key futures, which can be tested with the design

• Libero SoC v2022.2
• SoftConsole v2022.2-RISC-V-747
• PolarfireSoC MSS Configurator v2022.2
• HSS (Hardware System Service)
• Yocto
• UART
• ETH
• USB
• I2C
• QSPI flash
• DDR3 memory
• User LED

Notes :

• add every update file on the download
• add design changes on description

• add known Design issues and general notes for the current revision
• do not delete known issue, add fixed version time stamp if  issue fixed

Notes :

• list of software which was used to generate the design

Notes :

• list of hardware which was used to generate the design
• mark the module and carrier board, which was used tested with an ^*

^*used as reference

^*used as reference

^*used as reference

Notes :

• content of the zip file

Notes :

• prebuilt files
• Template Table:

  • 
    

    Scroll Title
    anchor Table_PF title-alignment center title Prebuilt files (only on ZIP with prebult content)
    Scroll Table Layout orientation portrait sortDirection ASC repeatTableHeaders default style widths sortByColumn 1 sortEnabled false cellHighlighting true File File-Extension Description Libero Project File *.prjx FlashPro Express Job *.job Constraint File *.pdc Timing Constraint File *.sdc Components in Block Design *.cxf Configuration File *.cfg Software-Application-File *.elf Software application for SoftConsole Device Tree *.dtb Device tree blob CONF-File *.conf Boot configuration file (extlinux.conf) Yocto linux image *.wic This File can be flashed via bmaptool on the SD card. Yocto linux image *.img Linux image for SD card

    
    

• Important set new Quartus version link on every Design update of new Quartus version!
• Set Link to download folder (Remove ../de/.. ../en/.. from url) for example: https://shop.trenz-electronic.de/Download/?path=Trenz_Electronic/Modules_and_Module_Carriers/6x8/TEI0006/Reference_Design/21.4/test_board

• Basic Design Steps

• Add/ Remove project specific description

Reference Design is available with and without prebuilt files. It's recommended to use TE prebuilt files for first launch.

Note:

• Programming and Startup procedure

Check Module and Carrier TRMs for proper HW configuration before you try any design.

Reference Design is also available with prebuilt files. It's recommended to use TE prebuilt files for first launch.

Note:

• Description of Block Design - Project, Block Design - Platform Designer, ... Block Design Pictures from Export...

• optional chapter separate

• sections for different apps

----------------------------------------------------------

General Example:

hello_tei0006

Hello TEI0006 is a Hello World example as endless loop instead of one console output.

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (C) 2021 Microchip Technology Inc.
 * Padmarao Begari <padmarao.begari@microchip.com>
 */

/dts-v1/;

#include "microchip-mpfs.dtsi"
#include "dt-bindings/gpio/gpio.h"

/* Clock frequency (in Hz) of the rtcclk */
#define RTCCLK_FREQ		1000000

/ {
	model = "Microchip PolarFire-SoC Icicle Kit";
	compatible = "microchip,mpfs-icicle-kit", "microchip,mpfs";

	aliases {
		serial1 = &uart1;
		ethernet0 = &mac0;
		spi0 = &qspi;
	};

	chosen {
		stdout-path = "serial1";
	};

	cpus {
		timebase-frequency = <RTCCLK_FREQ>;
	};

	ddrc_cache: memory@80000000 {
		device_type = "memory";
		reg = <0x0 0x80000000 0x0 0x40000000>;
		clocks = <&clkcfg CLK_DDRC>;
		status = "okay";
	};
        
};

&uart1 {
	status = "okay";
};

&mmc {
	status = "okay";
	bus-width = <4>;
	disable-wp;
	cap-mmc-highspeed;
	cap-sd-highspeed;
    cd-debounce-delay-ms;
	card-detect-delay = <200>;
	mmc-ddr-1_8v;
	mmc-hs200-1_8v;
	sd-uhs-sdr12;
	sd-uhs-sdr25;
	sd-uhs-sdr50;
	sd-uhs-sdr104;
};

&i2c1 {
	status = "okay";
	clock-frequency = <100000>;

};



&mac1 {
	status = "disabled";
};

&mac0 {
	status = "okay";
	phy-mode = "sgmii";
	phy-handle = <&phy0>;
	phy0: ethernet-phy@1 {
		device-type = "ethernet-phy";
		reg = <1>;       
        reset-names = "ETH_RST";
        reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
	};
};



&qspi {
	status = "okay";
	num-cs = <1>;
	flash0: spi-nor@0 {
		compatible = "spi-nor";
		reg = <0x0>;
		spi-tx-bus-width = <4>;
		spi-rx-bus-width = <4>;
		spi-max-frequency = <20000000>;
		spi-cpol;
		spi-cpha;
	};
};
 

// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/* Copyright (c) 2020-2021 Microchip Technology Inc */

/dts-v1/;

#include "mpfs.dtsi"
#include "mpfs-icicle-kit-fabric.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/phy/phy.h>

/* Clock frequency (in Hz) of the rtcclk */
#define MTIMER_FREQ		1000000

/ {
	#address-cells = <2>;
	#size-cells = <2>;
	model = "Microchip PolarFire-SoC Icicle Kit";
	compatible = "microchip,mpfs-icicle-reference-rtlv2209", "microchip,mpfs-icicle-kit",
		     "microchip,mpfs";

	aliases {
		ethernet0 = &mac0;
		serial0 = &mmuart0;
		serial1 = &mmuart1;
		serial2 = &mmuart2;
		serial3 = &mmuart3;
		serial4 = &mmuart4;
	};

	chosen {
		stdout-path = "serial1:115200n8";
	};

	cpus {
		timebase-frequency = <MTIMER_FREQ>;
	};
    


    //******************************************************//
    
    ddrc_cache: memory@80000000 {
		device_type = "memory";
		reg = <0x0 0x80000000 0x0 0x40000000>;
		status = "okay";
	};
    
    reserved-memory {	
        #address-cells = <2>;
		#size-cells = <2>;
        
		ranges;
        
		fabricbuf0ddrc: buffer@A0000000 {
			compatible = "shared-dma-pool";
			reg = <0x0 0xA0000000 0x0 0x2000000>;
			no-map;
		};
	};
    
	udmabuf0 {
		compatible = "ikwzm,u-dma-buf";
		device-name = "udmabuf-ddr-c0";
		minor-number = <0>;
		size = <0x0 0x2000000>;
		memory-region = <&fabricbuf0ddrc>;
		sync-mode = <3>;
	};
    
    
    //******************************************************//
    
    usb_phy: usb_phy {
    	#phy-cells = <0>;
        //compatible = "ulpi-phy";
		compatible = "usb-nop-xceiv";
		reset-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
        reset-names = "OTG_RST";
    };
    
    
	soc {
	};
};

&can0 {
	status = "disabled";
};

&core_pwm0 {
	status = "okay";
};


&fpgadma {
	status = "okay";
};

&fpgalsram {
	status = "okay";
};

&gpio1 {
    status = "okay";
};

&gpio2 {
	interrupts = <53>, <53>, <53>, <53>,
		     <53>, <53>, <53>, <53>,
		     <53>, <53>, <53>, <53>,
		     <53>, <53>, <53>, <53>,
		     <53>, <53>, <53>, <53>,
		     <53>, <53>, <53>, <53>,
		     <53>, <53>, <53>, <53>,
		     <53>, <53>, <53>, <53>;
	status = "okay";
};

&i2c0 {
	status = "okay";
};

&i2c1 {
	status = "okay";    
	#address-cells = <1>;
    #size-cells = <0>;

	eeprom: eeprom@50 {
    	compatible = "atmel,24c02";
        reg = <0x50>;
        #address-cells = <1>;
        #size-cells = <1>;        
        eth0_addr: eth-mac-addr@FA {
            reg = <0xFA 0x06>;
        };
    };
};

&i2c2 {
	status = "okay";       
};

&mac0 {
	status = "okay";
	phy-mode = "sgmii";    
	nvmem-cells = <&eth0_addr>;
	nvmem-cell-names = "mac-address";    
	/delete-property/ local-mac-address;    
	phy-handle = <&phy0>;
	phy0: ethernet-phy@1 {
		device-type = "ethernet-phy";
		reg = <1>;       
		reset-names = "ETH_RST";
		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
	};
};

&mac1 {
	status = "disabled";
};


&mbox {
	status = "okay";
};

&mmc {
	status = "okay";
	bus-width = <4>;
	disable-wp;
	cap-sd-highspeed;
	cap-mmc-highspeed;
	mmc-ddr-1_8v;
	mmc-hs200-1_8v;
	sd-uhs-sdr12;
	sd-uhs-sdr25;
	sd-uhs-sdr50;
	sd-uhs-sdr104;
};

&mmuart1 {
	status = "okay";
};

&mmuart2 {
	status = "okay";
};

&mmuart3 {
	status = "okay";
};

&mmuart4 {
	status = "okay";
};


&qspi {
	status = "okay";
    num-cs = <1>;
};

&refclk {
	clock-frequency = <125000000>;
};


&spi0 {
	status = "okay";
};

&spi1 {
	status = "disabled";
};


&usb {
	status = "okay";
	dr_mode = "otg";  
    phys = <&usb_phy PHY_TYPE_USB2>;
};

 

• Note this list must be only updated, if the document is online on public doc!
• It's semi automatically, so do following
  

  • Add new row below first

  • Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> this point is will be deleted on newer pdf export template

  • Metadata is only used of compatibility of older exports