Versions Compared

Old Version 1

changes.mady.by.user Mohsen Chamanbaz

Saved on

compared with

New Version 2

changes.mady.by.user Mohsen Chamanbaz

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Page properties
hiddentrue
idComments

Template Revision 1.1

For carrier - module combination, create main getting started page for carrier Design Name always "TE Series Name" +Getting Started, for example "TE0701 Getting started" and add carrier/module combination in the description → link on the module resource page also

For whole board,  use the board name, for example "TEBF0911 Getting Started"

  • Change List 1.0 to 1.1
    • add table of content to sidebar


Page properties
hiddentrue
idComments

In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are:

  • Overview of the board (point out the LEDs, Ethernets, Switches and etc on the board overview)
  • Explain Switches functionality
  • Explain user LEDs

  • Explain the UART connection

  • Refer to the Reference Design

    Note

    For more information regarding how to draw a diagram, Please refer to "Diagram Drawing Guidline" .


TEB2000 with TEM0007

Overview

Scroll Title
anchorFigure_Overview
titleBoard Overview


Scroll Ignore
scroll-pdftrue
scroll-officetrue
scroll-chmtrue
scroll-docbooktrue
scroll-eclipsehelptrue
scroll-epubtrue
scroll-htmltrue


draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxtrue
revision15
diagramNameOverview
simpleViewerfalse
width
linksauto
tbstylehidden
diagramWidth641853


Scroll Only


Board Overview

NumberNote
1J14- Ethernet interface
2J5,J8,J9,J10- Bank voltage adjustment
3JB1,JB2,JB3- B2B connector
4J3- SD card socket
5J21- UART0 socket
6J4- UART1 socket
7J13- 5V voltage input
8J12- USB stick socket
9S6- Reset button (SRST) (Soft reset)
10S1- Reset button ( Hard reset)
11S2- Dip Switch
12U4- CPLD Chip

Power supply

Page properties
hiddentrue
idComments

The input power supply must be mentioned.

Single ??V 5V power supply with minimum current capability of ??A 1.5A is recommended to power on the board. 

DIP-Switches and Push Buttons

Page properties
hiddentrue
idComments

Explain all DIP switches functionality.

There is a two switch (S??S1 and S6) which is connected to RESET signalsignals, it resets these reset the system entirely. The S6 is a soft reset buttom and S1 create a reset signal via hardware.

Scroll Title
anchorTable_DIP_PB
titleDIP Switches /Push Buttons

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Signal

DesignatorB2BActive Level






There is no DIPs on TExxxx. In case of TE0790 (XMOD) usage, see DIPs modeTEM0007 module.

Jumpers

Page properties
hiddentrue
idComments

Explain all Jumpers functionality and connection.


Scroll Title
anchorTable_Jumpers
titleJumpers

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorConnected toB2BNote

Boot_R
Open:
Short:


LEDs

Page properties
hiddentrue
idComments

Explain all user LEDs functionality and connections.

There are three user LEDs which can be used for variant purposes.

Scroll Title
anchorTable_LED
titleCarrier LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorColorConnected toB2BActive LevelNote




















Scroll Title
anchorTable_LED_Module
titleModule LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorColorConnected toActive LevelNote












Scroll Title
anchorTable_LED_Carrier
titleCarrier LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorColorConnected toActive LevelNote











JTAG/UART

Page properties
hiddentrue
idComments

Explain JTAG or UART connection breifly.

JTAG and UART connections are available through mini USB connector.

Scroll Title
anchorTable_UART
titleUART

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Designator

Connected to

B2B Pin

XMOD Header JB?DirectionNote













Reference Designs

Page properties
hiddentrue
idComments

In this Section you must refer to the Reference Design (Test board) for the particular module.

For Example: TE0728 Reference Designs

Notes

Page properties
hiddentrue
idComments

In this Section you must refer to the Resources Page for the particular module.

For Example: TE0728 Resources



 


Scroll Only


HTML
<style>
.wiki-content .columnLayout .cell.aside {
width: 0%;
}</style>



Scroll pdf ignore


Custom_fix_page_content

Table of contents

Table of Contents
outlinetrue