Page History
...
Company | Trenz Electronic GmbH |
---|---|
PCN Number | PCN-JJJJMMDD20240617 |
Title | PCN-JJJJMMDD TEXXXX-XX TitleTE0841-02 to TE0841-03 Hardware Revision Change |
Subject | Hardware Revision Change |
Issue Date | JJJJMMDD2024-06-17 |
Products Affected
This change affects all Trenz Electronic TEXXXX Electronic TE0841-02 SoMs: TEXXXXTE0841-XX02*.
Affected Product | Replacement |
---|---|
TE | TE |
...
TE0841-02-31C21-A | TE0841-03-31C31-A |
TE0841-02-31C31-A | TE0841-03-31C31-A |
TE0841-02-31I21-A | TE0841-03-31I31-A |
TE0841-02-31I21-T | TE0841-03-31I31-T |
TE0841-02-32I21-A | TE0841-03-32I31-A |
TE0841-02-41C21-A | TE0841-03-41C31-A |
TE0841-02-41I21-A | TE0841-03-41I31-A |
TE0841-02-41I21-L | TE0841-03-41I31-L |
ED: Tabelle ist fertig!
9) Net names for pins 4 and 5 for U11 were swapped
10) C70, C71, C72, C73, C74, C75, C76, C77, C78, C79, C80, C81, C82, C83, C84, @{"Id":"DCAOQXUV\JQHEFKQF","ObjectType":2} were added
11) R79, R80, R81, @{"Id":"DCAOQXUV\JMYBYQWI","ObjectType":2}, @{"Id":"EPHSAIGN\BPFCMKYX","ObjectType":2} were added
12) R35 was changed from 4.7k to 2.37k
13) @{"Id":"XYRRDMIL\MFKJFQBA","ObjectType":2} was changed from 4u7 6.3V 0402 to 10u 16V 0603
14) TP3 - @{"Id":"XDGVVEDM\NERJUSPY","ObjectType":2} were added
15) R25, R26, R52, R57 were changed from 4k7 to 23k7
16) @{"Id":"GELWJSSA\TFQIAKLH","ObjectType":2} was changed from DSC1123DL5-200 to SIT9121AI-2B1-XXE-200.00000
17) All SCH symbols and PCB footprints were updated from libruary
18) @{"Id":"DCAOQXUV\DXJIAUUX","ObjectType":2} was changed from 110k to 124k, net "PL_GT_1V35" was renamed to "PL_GT_1V42"
19) @{"Id":"EPHSAIGN\YARQSJWM","ObjectType":2} setted as "DNP"
Changes
#36 Changed ferrid bead (L1 ... L6) from BKP0603HS121-T to MPZ0603S121HT000.
Type: BOM Change
Reason:EOL of component.
Impact: None.
#36 Swapped clock net name
Type: BOM Change
Reason:EOL of component.
Impact: None.
#1 Changed DCDC EN63A0QI (U7, U14) to LTM4638EY#PBF
Type: Schematic change
Reason: EOL of component.
Impact: None. Maximum continuous output current increased from 12A to 15A per DCDC.
#7 Changed load switch TPS27082LDDCR (Q1) to MP5077GG-Z and adapted circuit.
Type: Schematic Change
Reason: BOM Optimization.
Impact: None. Minor changes in electrical characteristics.
#7 Added diode (D2) between signals "INIT_B" and "PROG_B".
Type: Schematic Change
Reason: Keep FPGA in reset while signal "PROG_B" is low during initial power-up.
Impact: None.
#4 Added power supervisor STM6710LWB6F (U21) and connected it to system controller (U18) pin 5 via net "PG_ALL".
Type: Schematic Change
Reason: Improve power monitoring.
Impact: Improved power monitoring circuit by supervising additional voltage rails. If monitored voltages are out of range signal "PG_ALL" is triggered.
#31 Signal trace lengths changed
Type: PCB change
Reason: Result of changes above.
Impact: Changed trace length have to be taken into account in existing designs. The trace length for new revision will be available in TE0841 series pinout generator. Please check if change in trace length still matches your requirements. Adaption of carrier may be necessary.
#25 Added legal notices, system and power diagram. Updated revision history. Updated page count and order.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.
#1
Type:
Reason:
Impact:
Scroll Pagebreak |
---|
...