Page History
...
| Name | Direction | Pin | Description |
|---|---|---|---|
| ACBUS4 | 96 | FTDI / currently_not_used | |
| ACBUS5 | 88 | FTDI / currently_not_used | |
| ADBUS4 | out | 98 | constant 0 / currently_not_used |
| ADBUS7 | in | 97 | / currently_not_used |
| BDBUS0 | in | 87 | UART TX from FTDI |
| BDBUS1 | out | 86 | UART RX to FTDI |
| C_TCK | out | 81 | JTAG FTDI |
| C_TDI | out | 84 | JTAG FTDI |
| C_TDO | in | 83 | JTAG FTDI |
| C_TMS | out | 85 | JTAG FTDI |
| CM0 | in | 99 | DIP Switch S3-M1 |
| CM1 | in | 1 | DIP Switch S3-M2 |
CM2 | in | 51 | REV06+ only: DIP Switch S4-1 / RGPIO Bus (powered by VIOTB (FMC VADJ)) |
| EN_FMC | out | 31 | VADJ and 3V3V_FMC Power on |
| EN1 | out | 24 | Power Enable Pin for Module CPLD |
| FMC_PRSNT | in | 28 | FMC Card present pin (zero if not present) |
| FMC_SCL | out | 10 | FMC I2C |
| FMC_SDA | inout | 8 | FMC I2C |
| FMC_TCK | out | 4 | JTAG FMC / currently_not_used |
| FMC_TDI | out | 12 | JTAG FMC / currently_not_used |
| FMC_TDO | in | 9 | JTAG FMC / currently_not_used |
| FMC_TMS | out | 7 | JTAG FMC / currently_not_used |
| HDMI_SCL | inout | 47 | HDMI / used also for I2C FMC control |
| HDMI_SDA | inout | 45 | HDMI / used also for I2C FMC control |
| HDMI_SPDIF | out | 15 | HDMI / currently_not_used |
| HDMI_SPDIFOUT | in | 14 | HDMI / currently_not_used |
| JTAGEN | -- | 82 | Enable JTAG access to carrier CPLD for Firmware update (zero: JTAG routed to module, one: CPLD access) Set DIP Switch S3-JTAGEN to ON, for module access. |
| M_TCK | in | 91 | JTAG Module |
| M_TDI | in | 94 | JTAG Module |
| M_TDO | out | 95 | JTAG Module |
| M_TMS | in | 90 | JTAG Module |
| MIO10 | inout | 29 | MIO |
| MIO11 | inout | 19 | MIO |
| MIO12 | inout | 36 | MIO |
| MIO13 | inout | 30 | MIO |
| MIO14 | inout | 37 | MIO / Module UART0.RX << BDBUS0 |
| MIO15 | in | 18 | MIO / Module UART0.TX >> BDBUS1 |
| MODE | out | 27 | Boot Mode for Zynq Devices (Flash or SD) |
| NOSEQ | inout | 21 | No Sequence, connected to Module CPLD / currently_not_used |
| PG_C2M | out | 20 | Power Good for FMC |
| PGOOD | inout | 25 | connected to Module CPLD / currently_not_used |
| PHY_LED1 | out | 42 | PHY LED |
| PHY_LED2 | out | 43 | PHY LED |
| POK_FMC | in | 32 | FMC Power good from FMC VADJ DCDC |
| PX6 | inout | 49 | PMOD J2 |
| PX7 | inout | 48 | PMOD J2 |
| RESIN | out | 13 | Module Reset |
| REVISION_DETECION | in | 57 | REV06+ only: Detection / currently_not_used |
| S1 | in | 3 | User Pushbutton |
| S2 | in | 2 | User Pushbutton / global Reset |
| SD_DETECT | in | 40 | SD Detection |
| SD_WP | in | 41 | SD |
| SEL_SD | out | 39 | SD Selection, MMC SD Slot or PMOD J2 |
| ULED1 | out | 78 | LED D1 |
| ULED2 | out | 77 | LED D2 |
| ULED3 | out | 76 | LED D3 |
| ULED4 | out | 16 | LED D4 |
| ULED5 | out | 69 | LED D5, powered by VIOTB (FMC VADJ) |
| ULED6 | out | 68 | LED D6, powered by VIOTB (FMC VADJ) |
| ULED7 | out | 65 | LED D7, powered by VIOTB (FMC VADJ) |
| ULED8 | out | 64 | LED D8, powered by VIOTB (FMC VADJ) |
| USB_OC | in | 17 | USB Over Current |
| VID0 | out | 34 | VADJ Voltage selection (EN5335QI) |
| VID1 | out | 35 | VADJ Voltage selection (EN5335QI) |
| VID2 | out | 38 | VADJ Voltage selection (EN5335QI) |
| X6 | in | 60 | Module IO (powered by VIOTB (FMC VADJ)) |
| Y0 | in | 75 | I2C SCL (powered by VIOTB (FMC VADJ)) |
| Y1 | out | 66 | I2C SDA_OUT (powered by VIOTB (FMC VADJ)) |
| Y2 | in | 67 | RGPIO CLK (powered by VIOTB (FMC VADJ)) |
| Y3 | out | 70 | RGPIO TX (powered by VIOTB (FMC VADJ)) |
| Y4 | in | 74 | RGPIO RX (powered by VIOTB (FMC VADJ)) |
| Y5 | in | 71 | I2C SDA_IN (powered by VIOTB (FMC VADJ)) |
| Y6 | in | 63 | Module IO (powered by VIOTB (FMC VADJ)) |
...
Overview
Content Tools