Versions Compared

Old Version 5

changes.mady.by.user Thomas Dück

Saved on

compared with

New Version 6

changes.mady.by.user Thomas Dück

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Custom_table_size_100

Page properties
hiddentrue
idComments

Template Revision 1.1

For carrier - module combination, create main getting started page for carrier Design Name always "TE Series Name" +Getting Started, for example "TE0701 Getting started" and add carrier/module combination in the description → link on the module resource page also

For whole board,  use the board name, for example "TEBF0911 Getting Started"

  • Change List 1.0 to 1.1
    • add table of content to sidebar


Page properties
hiddentrue
idComments

In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are:

  • Overview of the board (point out the LEDs, Ethernets, Switches and etc on the board overview)
  • Explain Switches functionality
  • Explain user LEDs

  • Explain the UART connection

  • Refer to the Reference Design

    Note

    For more information regarding how to draw a diagram, Please refer to "Diagram Drawing Guidline" .


Overview

Scroll Title
anchorFigure_Overview
titleBoard Overview

draw.io Diagram
bordertrue
diagramNameTEI0050_Getting_Started_Overview
simpleViewerfalse
width
linksauto
tbstyletop
lboxtrue
diagramWidth472
revision1


Power supply

Page properties
hiddentrue
idComments

The input power supply must be mentioned.

Over Micro USB or VIN Pin (5V) possible.

JTAG/UART

Page properties
hiddentrue
idComments

Explain JTAG or UART connection breifly.

JTAG and UART connections are available through Micro USB connector.  External JTAG Programmer is not needed.

Scroll Title
anchorTable_UART
titleUART

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Pin name

Connected to

DirectionNote
BDBUS0E18inuart rx
BDBUS1F16outuart tx


Push Buttons

Page properties
hiddentrue
idComments

Explain all DIP switches functionality.

  • Reset Button: reset Cyclone V (connected to nCONFIG Pin)
  • User Button: connected to FPGA Pin L17

LEDs

Page properties
hiddentrue
idComments

Explain all user LEDs functionality and connections.

There are 2 status LEDs and 8 user LEDs which can be used for variant purposes.


Scroll Title
anchorTable_LED_Module
titleModule LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

NameColorConnected toActive LevelNote
Power LEDGreen3.3Vlow3.3V status LED
CONF_DONERedCONF_DONE pinhigh--
LED1RedP4high--
LED2RedM4high--
LED3RedM3high--
LED4RedN3high--
LED5RedV2high--
LED6RedL2high--
LED7RedL1high--
LED8RedK1high--


CRUVI Pin Header J3

The Pin Header J3 is based on CRUVI Standard. For more information, please visit www.cruvi.com.

The Pins of the pin header J3 are connected to the FPGA Bank 7A and 8A. With the VSEL pin the voltage of these banks must be selected between 1.8V and 3.3V (depends on connected periphery):

Scroll Title
anchorTable_UART
titleVSEL

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

VSEL

VADJ voltage

Note
01.8V--
13.3V--

The VSEL pin is connceted to N10.

Reference Designs

Page properties
hiddentrue
idComments

In this Section you must refer to the Reference Design (Test board) for the particular module.

For Example: TE0728 Reference Designs

Notes

Page properties
hiddentrue
idComments

In this Section you must refer to the Resources Page for the particular module.

For Example: TE0728 Resources





Scroll Only


HTML
<style>
.wiki-content .columnLayout .cell.aside {
width: 0%;
}</style>



Scroll pdf ignore


Custom_fix_page_content

Table of contents

Table of Contents
outlinetrue