Page History
...
CPLD Device with designator U5: LCMX02-1200HC. CC703S is minimum startup design.
Feature Summary
- JTAG Management
- UART Management
- Power Management
- Boot Mode Management
- Reset Management
- SD
- LED Management
Firmware Revision and supported PCB Revision
...
| Name / opt. VHD Name | Direction | Pin | Description |
|---|---|---|---|
| ACBUS4 | 141 | / currently_not_used | |
| ACBUS5 | 140 | / currently_not_used | |
| ADBUS4 | 143 | / currently_not_used | |
| ADBUS7 | 142 | / currently_not_used | |
| BCBUS0 | 122 | / currently_not_used | |
| BCBUS1 | 121 | / currently_not_used | |
| BDBUS2 | 133 | / currently_not_used | |
| BDBUS3 | 132 | / currently_not_used | |
| BDBUS4 | 128 | / currently_not_used | |
| BDBUS5 | 127 | / currently_not_used | |
| BDBUS6 | 126 | / currently_not_used | |
| BDBUS7 | 125 | / currently_not_used | |
| CM0 | in | 76 | DIP-S2 / used as JTAG Selection |
| CM1 | in | 75 / currently_not_used | DIP-S1 / used to disable SD_CD-PIN forwarding (To work with PCB REV02,03,03) |
| E_SD_CMD | 110 | / currently_not_used | |
| E_SD_DAT0 | 106 | / currently_not_used | |
| E_SD_DAT1 | 107 | / currently_not_used | |
| E_SD_DAT2 | 112 | / currently_not_used | |
| E_SD_DAT3 | 111 | / currently_not_used | |
| E_SD_SCLK | 109 | / currently_not_used | |
| EN1 | out | 81 | B2B Power Enable |
| FL_0 | inout | 28 | LED (D3-red) / Status / not connected on REV02,REV03,REV04 |
| FL_1 | inout | 27 | LED (D4-green) / Status / not connected on REV02,REV03,REV04 |
| FT_B_RX | out | 138 | FTDI UART |
| FT_B_TX / BDBUS0 | in | 139 | FTDI UART |
| JTAGEN | 120 | Enable JTAG access to CPLD for Firmware update (zero: normal IOs, one: CPLD JTAG access). Selectable over S2-3 | |
| M_TCK | in | 131 | JTAG from/to FTDI |
| M_TDI | in | 136 | JTAG from/to FTDI |
| M_TDO | out | 137 | JTAG from/to FTDI |
| M_TMS | in | 130 | JTAG from/to FTDI |
| MIO0 | in | 94 | DIP-S4 and B2B Pin / used as Boot Mode |
| MIO10 | 98 | / currently_not_used | |
| MIO11 | 97 | / currently_not_used | |
| MIO12 | in | 100 | B2B-Module UART2 TX |
| MIO13 | out | 99 | B2B-Module UART2 RX |
| MIO14 | out | 105 | B2B-Module UART RX |
| MIO15 | in | 95 | B2B-Module UART TX |
| MIO9 | out | 96 | SD_CD / not usable as SD_CD on REV02,REV03,REV04 |
| MODE | out | 83 | Boot Mode Pin. Switch Boot mode of Module (depends on module) |
| NOSEQ | inout | 78 | Add Pullup only / currently_not_used |
| PGOOD | inout | 82 | Add Pullup used for Status / currently_not_used |
| PHY_LED1 | out | 86 | Status / currently_not_used |
| PHY_LED1R | out | 92 | Status / currently_not_used |
| PHY_LED2 | out | 85 | Status / currently_not_used |
| PHY_LED2R | out | 91 | Status / currently_not_used |
| PROGMODE | out | 104 | Enable B2B Module JTAG access to CPLD for Firmware update |
| RESIN | out | 119 | Module Reset Pin on B2B connector |
| S1 | in | 114 | Push Button / Used as module Reset |
| SD_CD | in | 93 | Forward to MIO 9 / not connected on REV02,REV03,REV04 |
| SD_SEL | out | 113 | set to GND / currently_not_used |
| TCK_B | out | 1 | JTAG from/to Module |
| TDI_B | out | 3 | JTAG from/to Module |
| TDO_B / C_TDO | in | 2 | JTAG from/to Module |
| TMS_B | out | 4 | JTAG from/to Module |
| ULED1 / LED1 | out | 117 | LED (D1-red) / UART Monitoring |
| ULED2 / LED2 | out | 115 | LED /D2-green) / UART Monitoring |
| USB_OC | 73 | / currently_not_used | |
| X0 | 39 | / currently_not_used | |
| X1 | 38 | / currently_not_used | |
| X10 | 49 | / currently_not_used | |
| X11 | 50 | / currently_not_used | |
| X12 | 52 | / currently_not_used | |
| X13 | 54 | / currently_not_used | |
| X14 | 55 | / currently_not_used | |
| X15 | 56 | / currently_not_used | |
| X16 | in | 59 | UART2 on VG connector J2 |
| X17 | out | 60 | UART2 on VG connector J2 |
| X2 | 40 | / currently_not_used | |
| X3 | 41 | / currently_not_used | |
| X4 | 42 | / currently_not_used | |
| X5 | 43 | / currently_not_used | |
| X6 | 44 | / currently_not_used | |
| X7 | 45 | / currently_not_used | |
| X8 | 47 | / currently_not_used | |
| X9 | 48 | / currently_not_used |
...
| S2-2 | S2-3 | PROGMODE | JTAGEN | Description |
|---|---|---|---|---|
| OFF | OFF | 1 | 1 | Access to TE0703 CPLD |
| OFF | ON | 1 | 0 | Access to CPLD of B2B Module |
| ON | OFF | 0 | 1 | Access to TE0703 CPLD |
| ON | ON | 0 | 0 | Access to FPGA of B2B Module |
Note: LED1,2,3,4 are on and PHY LEDs blink slow, if S2-2 is set to OFF.
Power
EN1 is set to one.
NOSEQ and PGOOD pulled up to VDD.
Reset
RESIN is driven by S1 (Push Button). Button is debounced.
Boot Mode
MODE Pin is sourced by MIO. MIO0 connected DIP S2-4 and B2B connector. MIO is pulled up with CPLD and can be set to GND via DIP.
| S2-4 | MIO0 | Description |
|---|---|---|
| ON | 0 | def. SD-CARD Boot (for Zynq Modules), PHY LEDs glow orange |
| OFF | 1 | def. QSPI-Flash, PHY LEDs glow green |
UART
Primary UART:
MIO14 is driven by BDBUS0 (FTDI RX).
BDBUS1 (FTDI TX) is driven by MIO14 MIO15 .
Secondary UART:
MIO13 is driven by X16.
X17 is driven by MIO12.
SD
SD selection is set to GND (SD Card slot).
MIO9 is SD_CD and CM1(S2-1).Is S2-1 is ON, MIO9 is GND else status depends on SD_CD .
Note: PCB REV02,REV03,REV04 has no SD, set S2-1 to ON
LED
LED Priority is order of the description
| LED | Prio 0: Power | Prio 1: Modul CPLD access* | Prio 2 | Description|
|---|---|---|---|---|
| LED1 (D1-red)ON | Blink, if | CMD0=1 else not FTDI_RXDPower Good is low | ON | FTDI UART RX |
| LED2 (D2-green) | Blink, if Power Good is low | ON | FTDI UART TX | |
| LED3 (D3-red) | Blink, if Power Good is low | ON | User defined with B2B Pin JB2-99 | |
| LED4 (D4-green) | Blink, if Power Good is low | ON | User defined with B2B Pin JB2-90 | |
| PHY LEDs (green/orange) | Blink orange, if Power Good is low | Blink Green and orange | Green: Boot Mode set to QSPI, Orange: Boot Mode set to SD |
*Attention: LED1,2,3,
...
4 are on, if S2-2 is set to OFF. If S2-3 is OFF, TE0703 is in chain!
Appx. A: Change History and Legal Notices
Revision Changes
- REV01 REV02 to older REV01
- enable Enable CPLD access to module CPLD over DIP
- Add MIO0, SD_SEL, SD_CD, NOSEQ, PGOOD, 2LEDs, PHY LEDs
- Debounce button
- More status LED functionality
Document Change History
To get content of older revision got to "Change History" of this page and select older document revision number.
...
| Date | Document Revision | CPLD Firmware Revision | Supported PCB Revision | Authors | Description | ||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
| REV01REV02 | REV02*,REV03*,REV04*,REV05 |
| Work in progressREV 02 finished | ||||||||||||||||||||||||
| 2016-04-11 | v.1 | ---REV02 | REV02*,REV03*,REV04*,REV05 |
| Initial release | ||||||||||||||||||||||||
| All |
|
...
Overview
Content Tools