Page History
...
| Name / opt. VHD Name | Direction | Pin | Description |
|---|---|---|---|
| ACBUS4 | 141 | / currently_not_used | |
| ACBUS5 | 140 | / currently_not_used | |
| ADBUS4 | 143 | / currently_not_used | |
| ADBUS7 | 142 | / currently_not_used | |
| BCBUS0 | 122 | / currently_not_used | |
| BCBUS1 | 121 | / currently_not_used | |
| BDBUS2 | 133 | / currently_not_used | |
| BDBUS3 | 132 | / currently_not_used | |
| BDBUS4 | 128 | / currently_not_used | |
| BDBUS5 | 127 | / currently_not_used | |
| BDBUS6 | 126 | / currently_not_used | |
| BDBUS7 | 125 | / currently_not_used | |
| CM0 | in | 76 | DIP-S2 / used as JTAG Selection |
| CM1 | 75 | / currently_not_used | |
| E_SD_CMD | 110 | / currently_not_used | |
| E_SD_DAT0 | 106 | / currently_not_used | |
| E_SD_DAT1 | 107 | / currently_not_used | |
| E_SD_DAT2 | 112 | / currently_not_used | |
| E_SD_DAT3 | 111 | / currently_not_used | |
| E_SD_SCLK | 109 | / currently_not_used | |
| EN1 | out | 81 | B2B Power Enable |
| FL_0 | inout | 28 | LED (D3-red) / currently_not_used Status / not connected on REV02,REV03,REV04 |
| FL_1 | inout | 27 | LED (D4-green) / currently_not_used Status / not connected on REV02,REV03,REV04 |
| FT_B_RX | out | 138 | FTDI UART |
| FT_B_TX / BDBUS0 | in | 139 | FTDI UART |
| JTAGEN | 120 | Enable JTAG access to CPLD for Firmware update (zero: normal IOs, one: CPLD JTAG access). Selectable over S2-3 | |
| M_TCK | in | 131 | JTAG from/to FTDI |
| M_TDI | in | 136 | JTAG from/to FTDI |
| M_TDO | out | 137 | JTAG from/to FTDI |
| M_TMS | in | 130 | JTAG from/to FTDI |
| MIO0 | in | 94 | DIP-S4 and B2B Pin / used as Boot Mode |
| MIO10 | 98 | / currently_not_used | |
| MIO11 | 97 | / currently_not_used | |
| MIO12 | in | 100 | B2B-Module UART2 TX |
| MIO13 | out | 99 | B2B-Module UART2 RX |
| MIO14 | out | 105 | B2B-Module UART RX |
| MIO15 | in | 95 | B2B-Module UART TX |
| MIO9 | 96 | / currently_not_used | |
| MODE | out | 83 | Boot Mode Pin. Switch Boot mode of Module (depends on module) |
| NOSEQ | inout | 78 | Add Pullup only / currently_not_used |
| PGOOD | inout | 82 | Add Pullup used for Status / currently_not_used |
| PHY_LED1 | out | 86 | Status / currently_not_used |
| PHY_LED1R | out | 92 | Status / currently_not_used |
| PHY_LED2 | out | 85 | Status / currently_not_used |
| PHY_LED2R | out | 91 | Status / currently_not_used |
| PROGMODE | out | 104 | Enable B2B Module JTAG access to CPLD for Firmware update |
| RESIN | out | 119 | Module Reset Pin on B2B connector |
| S1 | in | 114 | Push Button / Used as module Reset |
| SD_CD | 93 | / currently_not_used / not connected on REV02,REV03,REV04 | |
| SD_SEL | out | 113 | const. zero set to GND/ currently_not_used |
| TCK_B | out | 1 | JTAG from/to Module |
| TDI_B | out | 3 | JTAG from/to Module |
| TDO_B / C_TDO | in | 2 | JTAG from/to Module |
| TMS_B | out | 4 | JTAG from/to Module |
| ULED1 / LED1 | out | 117 | LED (D1-red) / UART Monitoring |
| ULED2 / LED2 | out | 115 | LED /D2-green) / UART Monitoring |
| USB_OC | 73 | / currently_not_used | |
| X0 | 39 | / currently_not_used | |
| X1 | 38 | / currently_not_used | |
| X10 | 49 | / currently_not_used | |
| X11 | 50 | / currently_not_used | |
| X12 | 52 | / currently_not_used | |
| X13 | 54 | / currently_not_used | |
| X14 | 55 | / currently_not_used | |
| X15 | 56 | / currently_not_used | |
| X16 | in | 59 | UART2 on VG connector J2 |
| X17 | out | 60 | UART2 on VG connector J2 |
| X2 | 40 | / currently_not_used | |
| X3 | 41 | / currently_not_used | |
| X4 | 42 | / currently_not_used | |
| X5 | 43 | / currently_not_used | |
| X6 | 44 | / currently_not_used | |
| X7 | 45 | / currently_not_used | |
| X8 | 47 | / currently_not_used | |
| X9 | 48 | / currently_not_used |
...
Overview
Content Tools