Page History
Legend:
: Attention: Carrier/Module combination only with special condition or PCB modification possible
: Supported
: Supported with limitations
: Not Supported
: Table currently not complete, see TRM of Module and carrier
TE0701
FMC(1) | FMC Vadj | PMODS | ETH | HDMI | CL Connector | SD Card | USB Host | VBATT | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
TE0710 | Support | | | no connection | Not supported | not used | |||||||||||||
TE0711 | Support | | | | | Not supported | not used | ||||||||||||
TE0712 | Support | | | | | Not supported | not used | ||||||||||||
TE0713 | Support | | not supported | | | Not supported | not used | ||||||||||||
TE0715-15 | Support | Full support | | Full support | | Full support | Full support | ||||||||||||
TE0715-30 | Support | | Full support | | Full support | Full support | |||||||||||||
TE0720 | Support | Full support | Full support | Full support | Full support | ||||||||||||||
TE0741 | Support | | | Not supported | Not supported | not used | |||||||||||||
TE0841 | Support | MGT's | Not supported | Not supported | used for Key RAM | ||||||||||||||
TE0820 | |||||||||||||||||||
TE0841 |
- (1) FMC is a LPC Connector on TE0701: DP0_..., GBTCLK0_... and TRST_L Pins are not connected. GA0 and GA1 set to GND. I2C and JTAG access over CPLD.
Separate TE0701_FMC_PINOUT table (PDF/XLSX) is available on: Trenz_Electronic Download-Pinout - (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
TE0703
ETH | SD Card | USB Host | Reset | User LEDs | USB UART | USB JTAG | |
---|---|---|---|---|---|---|---|
TE0710 |
2 |
TE0711 |
TE0712 |
TE0713 |
TE0715-15 | |||||||
TE0715-30 | |||||||
TE0720 | |||||||
TE0741 | |||||||
TE0820 | |||||||
TE0841 |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
TE0705
PMODS | ETH | SD Card | USB Host | |
---|---|---|---|---|
TE0710 |
TE0711 |
TE0712 |
100 MBit |
TE0713 |
TE0715-15 | ||||
TE0715-30 | ||||
TE0720 | ||||
TE0741 | ||||
TE0820 | ||||
TE0841 |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
TE0706
ETH1 | ETH2 | SD Card | USB Host | |
---|---|---|---|---|
TE0710 | | | Not supported | |
TE0711 | | | Not supported | |
TE0712 | 100 MBit | | Not supported | |
TE0713 | Not supported | |||
TE0715 | Full support | Full support | Full support | |
TE0720 | Full support | Full support | Full support | Full support |
TE0741 | Not supported | |||
TE0841 | Not supported |
TEBA0841
...
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
TEBA0841
Overview
Content Tools