Page History
Legend:
: Attention: Carrier/Module combination only with special condition or PCB modification possible
: Supported
: Supported with limitations
: Not Supported
: Table currently not complete, see TRM of module and carrier
TE0701
FMC(1) | FMC Vadj | PMODS | ETH | HDMI | CL Connector(5) | SD Card | USB Host | VBATT | |
---|---|---|---|---|---|---|---|---|---|
TE0710 | |||||||||
TE0711 | |||||||||
TE0712 | |||||||||
TE0713 | |||||||||
TE0715-15 | |||||||||
TE0715-30 | |||||||||
TE0720 | |||||||||
TE0741 | |||||||||
TE0820 | |||||||||
TE0841 |
- (1) FMC is a LPC Connector (no gigabit transceivers) on TE0701: I2C and JTAG access over CPLD.
Separate TE0701_FMC_PINOUT table (PDF/XLSX) is available on: Trenz_Electronic Download-Pinout - (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
- (5) CL Connector is usable as Cameralink only with module that map LVDS pins to this connector
- (6) Works, but without carrier board modification out of specification: TE0701 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
- (7) PS battery operated voltage (1.2V–1.5V).
TE0703
ETH | SD Card | USB Host | Reset | User LEDs | USB UART | USB JTAG | |
---|---|---|---|---|---|---|---|
TE0710 | |||||||
TE0711 | |||||||
TE0712 | |||||||
TE0713 | |||||||
TE0715-15 | |||||||
TE0715-30 | |||||||
TE0720 | |||||||
TE0741 | |||||||
TE0820 | |||||||
TE0841 |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
- (6) Works, but without carrier board modification out of specification: TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
TE0705
PMODS | ETH | SD Card | USB Host | |
---|---|---|---|---|
TE0710 | ||||
TE0711 | ||||
TE0712 | 100 MBit | |||
TE0713 | ||||
TE0715-15 | ||||
TE0715-30 | ||||
TE0720 | ||||
TE0741 | ||||
TE0820 | ||||
TE0841 |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
- (6) Works, but without carrier board modification out of specification: TE0705 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
TE0706
ETH1 | ETH2 | SD Card | USB Host | |
---|---|---|---|---|
TE0710 | ||||
TE0711 | ||||
TE0712 | 100 MBit | |||
TE0713 | ||||
TE0715-15 | ||||
TE0715-30 | ||||
TE0720 | ||||
TE0741 | ||||
TE0820 | ||||
TE0841 |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
- (6) Works, but without carrier board modification out of specification: TE0706 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
TEBA0841
SFP | USB Host | SD Card "J4 2x5 Pin Header(2.54)" | GPIO
| XMOD (JTAG/UART) "JX1 2x6 Pin Header (2.54)" | GPIO (JTAG/UART/MGT REFCLK) "J3 2x8 Pin Header(2.54)" | |
---|---|---|---|---|---|---|
TE0710 | ||||||
TE0711 | ||||||
TE0712 | ||||||
TE0713 | ||||||
TE0715 | ||||||
TE0715-30 | ||||||
TE0720 | ||||||
TE0741 | ||||||
TE0820 | ||||||
TE0841 |
...
Overview
Content Tools