Page History

<!--
Template Revision 1.65
(HTML comments will be not displayed in the document, no need to remove them. For Template/Skeleton changes, increase Template Revision number. So we can check faster, if the TRM style is up to date).
-->

<!--
General Notes:
If some section is CPLD firmware dependent, make a note and if available link to the CPLD firmware description. It's in the TE shop download area in the corresponding module -> revision -> firmware folder.
-->

<!--
General Notes:
Designate all graphics and pictures with a number and a description. For example "Figure 1: TE07xx-xx Block Diagram" or "Table 1: Initial delivery state". "Figure x" and "Table x" have to be formatted to bold.  
-->

<!--
Download Link: Go to Base Folder of the Module or Carrier, for example : https://shop.trenz-electronic.de/en/Download/?path=Trenz_Electronic/TE0712
Use english URL "../en/..
 -->

Overview

<!--
Wiki Link: Go to Base Folder of the Module or Carrier, for example : https://wiki.trenz-electronic.de/display/PD/TE0712
 -->

Refer to https://wiki.trenz-electronic.de/display/PD/TEM0001 for the current online version of this manual and other available documentation.

The Trenz Electronic TEM0001 is a low cost small-sized FPGA module integrating a Microsemi SmartFusion2 FPGA SoC and 8 MByte Flash memory for configuration and operation.

Key Features

• Microsemi SmartFusion2 SoC FPGA

• 8 MByte SDRAM

• 8 MByte QSPI Flash memory

• 25 MHz system clock and 32.768 KHz auxiliary clock
• JTAG and UART over Micro USB2 connector
• 1x 3-pin header for Live Probes
• 1x PMOD header providing 8 GPIOs

• 2x 14-pin headers (2,54 mm pitch) providing 23 GPIOs

• 9 user LEDs

• 1 user push button
• 3.3V single power supply with on-board voltage regulators
• Size 61.5 x 25 mm
  
  

Additional assembly options are available for cost or performance optimization upon request.

Block Diagram

Figure 1: TEM0001-01 block diagram

Main Components

Image AddedImage Added

Figure 2: TEM0001-01 FPGA module

1. Microsemi SmartFusion2 FPGA SoC, U5
2. 8 Mbyte SDRAM 166MHz, U2
3. Micro USB2 B socket (receptacle), J9
4. Switch button (reset), S1
5. Switch button (user), S2
6. Red LED (user), D10
7. Green LED (indicating supply voltage), D1
8. 8x red LEDs (user), D2 - D9
9. FTDI USB2 to JTAG/UART adapter, U3
10. 8 Mbyte QSPI Flash memory, U1
11. 32.768 KHz auxiliary crystal oscillator, Y1
12. 25 MHz main crystal oscillator, Y2
13. 1x14 pin header (2.54mm pitch), J2
14. 1x6 pin header (2.54mm pitch), J4
15. 3-pin header (2.54mm pitch), J3
16. 1x14 pin header (2.54mm pitch), J1
17. 2x6 Pmod connector, J6

Initial Delivery State

Table 1: Initial delivery state of programmable devices on the module

Boot Process

By default the configuration mode pins of the FPGA are set to QSPI mode, hence the FPGA is configured from serial Flash memory at system start-up. The JTAG interface of the module is provided for storing the initial FPGA configuration data to the QSPI flash memory.

Signals, Interfaces and Pins

I/Os on Pin Headers and Connectors

I/O signals of the FPGA SoC's I/O banks connected to the board's pin headers and connectors:

Table 2: General overview of single ended I/O signals connected to pin headers and connectors

FPGA I/O banks

Table 3: General overview of FPGA I/O banks

JTAG Interface

Primary JTAG access to the FPGA SoC device U5 is provided through Micro USB2 B connector J9. The JTAG interface is created by the FTDI FT2232H USB2 to JTAG/UART adapter IC U3. 

Optionally 1x6 male pin header J4 can be fitted on board for access to the JTAG interface on board. The pin assignment of header J4 is shown on table below:

Table 4: optional second JTAG interface or GPIO (JTAGSEL dependent)

QSPI Interface

The QSPI interface of the FPGA device is routed to and used by the on-module QSPI flash IC U1:

Table 5: QSPI interface signals

On-board Peripherals

Quad SPI Flash Memory

On-module QSPI flash memory (U7) is provided by Winbond Serial Flash Memory W74M64FV with 64 MBit (8 MByte) storage capacity. This non volatile memory is used to store initial FPGA configuration. Besides FPGA configuration, remaining free flash memory can be used for user application and data storage.

SDRAM

The TEM0001 FPGA module is equipped with a Winbond W9864G6JT 64 MBit (8 MByte) SDRAM chip U2. This SDRAM chip is connected to the FPGA bank 4 and 7 via 16-bit memory interface with 166MHz clock frequency and CL3 CAS latency.

FTDI FT2232H IC

The FTDI chip U3 converts signals from USB2.0 to a variety of standard serial and parallel interfaces. Refer to the FTDI data sheet to get information about the capacity of the FT2232H chip.
FTDI FT2232H chip is used in MPPSE mode for JTAG, 6 I/O's of Channel B are routed to the bank 1 of the FPGA SoC and are usable for example as UART interface.

The configuration of FTDI FT2232H chip is pre-programmed on the EEPROM U9.

System Clock Oscillator

The FPGA SoC module has following reference clocking signals provided by on-board oscillators:

Table 6: Clock sources overview

On-board LEDs

There are 10 LEDs fitted on the FPGA module board. The LEDs are user configurable to indicate for example any system status.

Table 7: LEDs of the module

Push Buttons

The TEM0001 FPGA module is equipped with two push buttons S1 and S2:

Table 8: Push buttons of the module

Connectors

All connectors are are for 100mil headers, all connector locations are in 100mil (2.54mm) grid. The module's PCB provides footprints to mount and solder optional pin headers, if those are not factory-fitted on module.

Power and Power-On Sequence

To power-up a module, power supply with minimum current capability of 1A is recommended.

Power Supply

The FPGA module can be power-supplied through Micro USB2 connector J9 with supply voltage 'USB-VBUS' or alternative through pin header J2 with supply voltage 'VIN'.

The TEM0001 module needs one single power supply of 5.0V nominal.

There are following dependencies how the initial voltage of the extern power supply is distributed to the on-board DCDC converters:

Image Added

Figure 3: Power Distribution Diagram

Power Consumption

Table 9: Module power consumption

*TBD - To Be Determined.

Actual power consumption depends on the FPGA design and ambient temperature.

Power-On Sequence

There is no specific or special power-on sequence, just one single power source is needed.

Technical Specifications

Absolute Maximum Ratings

Table 10: Absolute maximum ratings

Recommended Operating Conditions

Table 11: Recommended operating conditions

Physical Dimensions

Please note that two different units are used on the figures below, SI system millimeters (mm) and imperial system thousandths of an inch(mil). This is because of the 100mil pin headers used, see also explanation below. To convert mils to millimeters and vice versa use formula 100mil's = 2,54mm.

• Board size: PCB 25mm × 61,5mm. Notice that some parts the are hanging slightly over the edge of the PCB like the the Micro USB2 B connector, which determine the total physical dimensions of the carrier board. Please download the assembly diagram for exact numbers.

• PCB thickness: ca. 1.65mm

• Highest part on the PCB without fitted headers and connectors is the Micro USB2 B connector, which has an approximately hight of 3 mm. Please download the step model for exact numbers.

Image Added      Image Added

Figure 4: Module physical dimensions drawing

Revision History

Hardware Revision History

Table 12: Module hardware revision history

Hardware revision number is printed on the PCB board together with the module model number separated by the dash.

Image Added

Figure 5: Module hardware revision number

Document Change History

Table 13: Document change history

Disclaimer