...
Scroll pdf title |
---|
title | Firmware update comparison table. |
---|
|
generation | 2: recovery boot | 3: recovery boot | 3: regular boot |
---|
boot mode (EEPROM switch) | recovery (off, then on) | recovery (off, then on) | regular (always on) |
---|
VID | 04B4 | 04B4 | 0BD0 |
---|
PID | 8613 | 8613 | 0300 |
---|
device | Cypress generic USB | Cypress generic USB | TE USB FX2 |
---|
required driver | recovery driver | recovery driver | regular driver |
---|
update applications | Cypress USB Console Cypress USB Control Center |
---|
|
Further documentation:
...
information is shown in the following video play lists.
Include Page |
---|
| IN:Videos: generation 2 to generation 3 migration (firmware + driver) |
---|
|
...
| IN:Videos: generation 2 to generation 3 migration (firmware + driver) |
---|
|
Include Page |
---|
| IN:Videos: generation 3 TE USB FX2 (firmware update) |
---|
| IN:Videos: generation 3 TE USB FX2 (firmware update) |
---|
|
Widget Connector |
---|
width | 400 |
---|
url | http://www.youtube.com/watch?v=QZk3C4gtOk4&list=PL_T7L7yrNs4m_fnCtziSB81yhPP710AV4 |
---|
height | 300 |
---|
|
| Update USB FX2 microcontroller firmware (generation 3), using "Cypress USB Console" This video shows how to update a Trenz Electronic device form generation 3 (old firmware) to generation 3 (new firmware), using "Cypress USB Console". The video has been recorded on a Microsoft Windows 7 (64 bit) operating system with a TE0630-00 FPGA module connected to a USB port, but the procedure is almost the same for any Trenz Electronic USB FX2 device. Please note that unlike TE0300 and TE0320, TE0630-00 has no master-reset, thus a power-on reset is required.
|
Widget Connector |
---|
width | 400 |
---|
url | http://www.youtube.com/watch?v=GrHYyBj7lzI&list=PL_T7L7yrNs4m_fnCtziSB81yhPP710AV4 |
---|
height | 300 |
---|
|
| Update USB FX2 microcontroller firmware (generation 3) using "Cypress USB Control Center" This video shows how to update a Trenz Electronic device form generation 3 (old firmware) to generation 3 (new firmware), using "Cypress USB Control Center". The video has been recorded on a Microsoft Windows 7 (64 bit) operating system with a TE0630-00 FPGA module connected to a USB port, but the procedure is almost the same for any Trenz Electronic USB FX2 device. Please note that unlike TE0300 and TE0320, TE0630-00 has no master-reset, thus a power-on reset is required. |
Widget Connector |
---|
width | 400 |
---|
url | http://www.youtube.com/watch?v=HijM1exGyLE&list=PL_T7L7yrNs4m_fnCtziSB81yhPP710AV4 |
---|
height | 300 |
---|
|
| Powered Reset procedure for TE0300 and TE0320 (based on "Update USB FX2 microcontroller firmware" videos)This video assumes that you have followed the "Update USB FX2 microcontroller firmware (generation 3) using Cypress USB Control Center" video and implements the "powered reset" as reset (1:31 to 2:14 of the previous video). This video shows how to realize a powered reset for a TE0320 or a TE0300 device. The video has been recorded on a Microsoft Windows 7 (64 bit) operating system with a TE0300-01 FPGA module connected to a USB port. Please note that, unlike TE0300 and TE0320, TE0630 has no master reset switch, thus a power-on reset is required. |