Versions Compared

Old Version 91

changes.mady.by.user John Hartfiel

Saved on

compared with

New Version 92

changes.mady.by.user John Hartfiel

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

 Storage Device Name

Content

Notes

SPI Flash OTP Area

Empty, not programmed

Except serial number programmed by flash vendor.

SPI Flash Quad Enable bit

Programmed

-

SPI Flash main array

Not programmed

-

eFUSE USER

Not programmed

-

eFUSE Security

Not programmed

-
Si5338 OTP NVMNot programmed-
CPLD (LCMXO2-256HC)SC0820-02 QSPI FirmwareSee Boot Process section.

Table 1: Initial delivery state of programmable devices on the module

...

Power-On Sequence

The TE0820 SoM meets the recommended criteria to power up the Xilinx Zynq chip properly by keeping a specific sequence of enabling the on-board DC-DC converters dedicated to the particular functional units of the Zynq chip and powering up the on-board voltages.

...

Date

Revision

Contributors

Description

Page info
modified-date
modified-date
dateFormatyyyy-MM-dd

Page info
infoTypeCurrent version
dateFormatyyyy-MM-dd
prefixv.
typeFlat

Page info
infoTypeModified by
dateFormatyyyy-MM-dd
typeFlat

  • typo correction
  • changes on power section description
2020-03-16b.87John Hartfiel
  • Corrected PLL section
  • Corrected Designators USB, ETH PHY, CLK section
2020-02-03v.85Martin Rohrmüller
  • Corrected #MIOs for QSPI and USB in block diagram
2019-11-28v.81Martin Rohrmüller
  • typo and designator in section USB interface corrected
2019-10-30v.80John Hartfiel
  • typo correction
2019-09-17v79Martin Rohrmüller
  • Updated according to PCN-20190110: eMMC, QSPI-Flash

2019-07-17

v.78Martin Rohrmüller
  • Corrected PJTAG Mio Pin29 in table 8

2019-05-08

v.77John Hartfiel
  • Corrected EEPROM I2C Address
  • Correction USB PHY connection

2018-11-12

v.74

John Hartfiel
  • update boot section

2018-08-30

v.73John Hartfiel
  • typo correction
  • update CPLD section
  • add LEDs to component list
  • add 3D picture of REV03 instead of REV01 picture

2018-07-12

v.69Ali Naseri
  • Update PCB Rev03

2018-06-11

v.61John Hartfiel
  • Rework chapter currently available products
  • add PJTAG note to MIOtable
2018-03-12v.54
  • Correction Power Rail Section
2017-11-20v.51John Hartfiel
  • Correction Default MIO Configuration Table
2017-11-10v.50John Hartfiel
  • Replace B2B connector section
2017-10-18v.49John Hartfiel
  • add eMMC section
2017-09-25v.48John Hartfiel
  • Correction in the "Board to Board (B2B) I/Os" section
  • Update in the "Variants Currently In Production" section
2017-09-18v.47John Hartfiel
  • Update PS MIO table
2017-08-30v.46Jan Kumann
  • MGT lanes section added.

2017-08-24

v.36

John Hartfiel
  • Correction in the  "Key Features" section.
2017-08-21v.34John Hartfiel
  • "Initial delivery state" section updated.
2017-08-21v.33Jan Kumann
  • HW revision 02 block diagram added.
  • Power distribution and power-on sequence diagram added.
  • System Controller CPLD and DDR4 SDRAM sections added.
  • TRM update to the template revision 1.6
  • Weight section removed.
  • Few minor corrections.



2017-08-18


v.7

John Hartfiel
  • Style changes
  • Updated "Boot Mode", "HW Revision History", "Variants Currently In Production" sections
  • Correction of MIO SD Pin-out, System Controller chapter
  • Update and new sub-sections on "On Board Peripherals and Interfaces" sections

2017-08-07

v.5

Jan Kumann

  • Initial version
--all

Page info
infoTypeModified users
typeFlat
showVersionsfalse

  • ---

...