Page History

...

• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
• (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
• (6) REV03 select correct SDIO voltage by jumper. REV02 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).
• (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage

TEB0707

	ETH	SD Card	USB Host	HS CA(15)	HS CB(15)	HS CC(15)	LS CA(16)	User LEDs(17)	USB UART	USB JTAG
TE0710		, 3.3V B16 I/O
TE0711		, 1.8V B16 I/O
TE0712	100 MBit	, 1.8V B13 I/O			, some fix 3.3V B14 I/O
TE0713					(19)
TE0715-15								(3x PL, 3x PS)
TE0715-30 (2)				, max  1.8V	, max  1.8V			(3x PL, 3x PS)
TE0720								(3x PL, 3x PS)
TE0741 (4)		, MGTs		(18)
TE0820 (2)		(6)		, max  1.8V	, max  1.8V	, max  1.8V		(3x PL, 3x PS)
TE0821 (2)		(6)			, max  1.8V			(3x PL, 3x PS)
TE0823 (2)		(6)		, max  1.8V	, max  1.8V	, max  1.8V		(3x PL, 3x PS)
TE0841 (2)(3)		, MGTs			, max  1.8V	, max  1.8V		(3x PL, 3x PS)

• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes connected to SD-Level shifter: TEB0707 - Leave J4 open.
• (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
• (6) Select correct SDIO voltage by jumper.
• (15) Fix 3.3V signals of CRUVI HS connectors are connected to MAX10 CPLD and can be used firmware dependent (In standard firmware not implemented).
• (16) Signals on CRUVI LS connector are connected to MAX10 CPLD and can be used firmware dependent (In standard firmware 4 input and 4 output).
• (17) LEDs are connected to MAX10 CPLD and can be used firmware dependent (In standard Firmware implemented.)
• (18) Not available on assembly variants with K70T.
• (19) Two diff. pairs connected to FT600 USB3 lanes. Other signals usable.

TEBA0841

	SFP	USB Host	SD Card "J4 2x5 Pin Header(2.54)"	GPIO "J20/J10 each 2x25 Pin Header(2.54)"	XMOD (JTAG/UART) "JX1 2x6 Pin Header (2.54)"	GPIO (JTAG/UART/MGT REFCLK) "J3 2x8 Pin Header(2.54)"
TE0710			,3.3V B16 I/O	(9)		(8)
TE0711		, device only(14)	,1.8V B16 I/O	(9)		, B34 CLK input
TE0712			,  B13 I/O	(9)		, B34 CLK input
TE0713		, device only(14)	,  B13 I/O	(9)
TE0715 (10)			(7)	(9)
TE0715-30 (10)			(7)	(9)
TE0720 (10)			(7)	(9)		, B34 CLK input
TE0741 (11)			,MGT's	(9)
TE0820 (10)			(6)	(9)
TE0821 (10)			(6)	(9)
TE0823 (10)			(6)	(9)
TE0841			,MGT's	(9)

...