Page History
This Trenz Electronic Starter Kit consists of a TE0808 module on a TEBF0808 base board in Mini-ITX Enclosure. See shop link for detailed content.
Wiki Links
Kit specific
- TEBF0808 Getting Started - Summarised documentation of Connectors, DIPs, LEDs
- TE081x and TE080x Starterkit montage instruction - Assembly instructions if you want to assemble it yourself
Module and Carrier separately
- TE0808 - UltraSoM+ - Wiki with TRM, reference projects, application notes and more
- TE0808 Resources - Links to all TE0808 Resources
- TEBF0808 - Wiki with TRM, application notes and more
- TEBF0808 Resources - Links to all TEBF0808 Resources
- TE0790 - XMOD - Wiki with TRM, application notes and more
- TE0790 Resources - Links to all TE0790 Resources
- Vivado/SDK/SDSoC AMD Development Tools - Short instructions for Vivado, SDK, SDSoC
- Project Delivery - AMD devices - General descriptions of reference designs and content
...
- Shop TE0808-Starter-Kit - contains prices, available stock, disposability, scope of delivery and more
...
AMD Software and Driver
- Vivado Design Suite - Xilinx AMD Design Software with JTAG drivers and documentation
- Xilinx AMD Download Area - All Xilinx AMD Software, Device Models and Libraries
Additional Documentation
| Table of Contents |
|---|
Important Notes
| Warning |
|---|
| Do not change XMOD DIP-Switch settings on TEBF0808. Do not swap the XMOD adapters the one marked with green dot must be closer to the SoM |
| Note |
|---|
ES devices are not included in all Vivado versions, for ES1 only: activate beta device see: FAQ - How can I activate beta devices? |
| Note |
|---|
For all Starter Kit's shipped before 2017-06-21: Enclosure Power and HD LED was swapped on connector. See "Enclosure Power Button, Reset Button, HDD LED and Power LED" section for correct connection. |
Getting Started
- TEBF0808 Getting Started - Basic note to start up Carrier with TE080x modules
Starter Kit Basic
Main Power Enclosure Location
Power Button , Reset Button, HDD LED and Power LED Enclosure Location
Default DIP Switch Settings
| Warning |
|---|
| Do not change XMOD DIP-Switch settings on TEBF0808. Do not swap the XMOD adapters the one marked with green dot must be closer to the SoM |
...
TE0790-02
(with green dot)
...
| DIP-Schalter | S4 |
|---|---|
| S4.1 | OFF |
| S4.2 | OFF |
| S4.3 | OFF |
| S4.4 | ON |
| DIP-Schalter | S5 |
|---|---|
| S5.1 | ON |
| S5.2 | ON |
| S5.3 | OFF |
| S5.4 | OFF |
| DIP-Schalter | S1 |
|---|---|
| S1.1 | ON |
| S1.2 | OFF |
| S1.3 | OFF |
| S1.4 | OFF |
| DIP-Schalter | S1 |
|---|---|
| S1.1 | ON |
| S1.2 | OFF |
| S1.3 | OFF |
| S1.4 | OFF |
Note: with CPLD Firmware REV06 or newer, S4.4 can be set to OFF, to save power, if Starter Kit is powered off with Power Button.
For more information, see:TEBF0808
SI5345 NVM Programming
SI5345 NVM is not programmed on factory, so modified FSBL is needed to get running output CLKS.
It it possible to program NVM of the SI5345 2 times, see Si5345
Starter Kit Cable Connection
Starter Kit will be shipped with all cable connected.
ATX Power
Module
FMC FAN
XMODs
Enclosure USB
Enclosure FAN1 and HDAUDIO
Enclosure Power Button , Reset Button, HDD LED and Power LED
...
Support
- For support, please go to http://forum.trenz-electronic.de/ or contact support@trenz-electronic.de
Overview
Content Tools