Versions Compared

Old Version 1

changes.mady.by.user Thomas Dück

Saved on

compared with

New Version Current

changes.mady.by.user Thomas Dück

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Custom_table_size_100

Page properties
hiddentrue
idComments

Template Revision 1.1

For carrier - module combination, create main getting started page for carrier Design Name always "TE Series Name" +Getting Started, for example "TE0701 Getting started" and add carrier/module combination in the description → link on the module resource page also

For whole board,  use the board name, for example "TEBF0911 Getting Started"

  • Change List 1.0 to 1.1
    • add table of content to sidebar


Page properties
hiddentrue
idComments

In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are:

  • Overview of the board (point out the LEDs, Ethernets, Switches and etc on the board overview)
  • Explain Switches functionality
  • Explain user LEDs

  • Explain the UART connection

  • Refer to the Reference Design

    Note

    For more information regarding how to draw a diagram, Please refer to "Diagram Drawing Guidline" .

TExxxx with TExxxx


Overview

scroll-ignore

Scroll Title
anchorFigure_Overview
titleBoard Overview
scroll-pdftrue
scroll-officetrue
scroll-chmtrue
scroll-docbooktrue
scroll-eclipsehelptrue
scroll-epubtrue
scroll-htmltrue
draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramDisplayNamelboxtruerevision1
diagramNameTEI0050_Getting_Started_Overview
simpleViewerfalse
width
linksauto
tbstyletop
lboxhiddentrue
diagramWidth641471

scroll-only

revision

Image Removed

3


Power supply

Page properties
hiddentrue
idComments

The input power supply must be mentioned.

Single ??V power supply with minimum current capability of ??A is recommended to power on the board. 

DIP-Switches and Push Buttons

Over Micro USB or VIN Pin (5V) possible.

JTAG/UART

Page properties
hiddentrue
idComments

Explain all DIP switches functionality.JTAG or UART connection breifly.

JTAG and UART connections are available through Micro USB connector.  External JTAG Programmer is not neededThere is a switch (S??) which is connected to RESET signal, it resets the system entirely.

Scroll Title
anchorTable_DIP_PBUART
title-alignmentcenter
titleDIP Switches /Push ButtonsUART

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Signal

DesignatorB2BActive Level

There is no DIPs on TExxxx. In case of TE0790 (XMOD) usage, see DIPs mode.

Jumpers

Pin name

Connected to

DirectionNote
BDBUS0E18inuart rx
BDBUS1F16outuart tx


Push Buttons

Page properties
hiddentrue
idComments

Explain all Jumpers DIP switches functionality and connection.

Scroll Title
anchorTable_Jumpers
titleJumpers
Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorConnected toB2BNoteBoot_ROpen:Short:

.

  • Reset Button: reset Cyclone V (connected to nCONFIG Pin)
  • User Button: connected to FPGA Pin L17

LEDs

Page properties
hiddentrue
idComments

Explain all user LEDs functionality and connections.

There are three 2 status LEDs and 8 user LEDs which can be used for variant purposes.


Scroll Title
anchorTable_LED_Module
title-alignmentcenter
titleCarrier Module LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

B2B
DesignatorNameColorConnected toActive LevelNote
Scroll Title
anchorTable_LED_Module
titleModule LEDs
Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorColorConnected toActive LevelNote Scroll Title
anchorTable_LED_Carrier
titleCarrier LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorColorConnected toActive LevelNote

JTAG/UART

Page properties
hiddentrue
idComments

Explain JTAG or UART connection breifly.

Power LEDGreen3.3Vlow3.3V status LED
CONF_DONERedCONF_DONE pinhigh--
LED1RedP4high--
LED2RedM4high--
LED3RedM3high--
LED4RedN3high--
LED5RedV2high--
LED6RedT2high--
LED7RedL1high--
LED8RedK1high--


CRUVI Pin Header J3

The Pin Header J3 is based on CRUVI Standard. For more information, please visit www.cruvi.com.

The Pins of the pin header J3 are connected to the FPGA Bank 7A and 8A. With the VSEL pin (connected to N10) the voltage of these banks (VADJ) must be selected between 1.8V and 3.3V (depends on connected periphery):JTAG and UART connections are available through mini USB connector.

Scroll Title
anchorTable_UART
title-alignmentcenter
titleUARTVSEL

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Note
VSEL

VADJ voltage

Note
01.8V--
13.3V--Designator

Connected to

B2B Pin

XMOD Header JB?Direction


Reference Designs

Page properties
hiddentrue
idComments

In this Section you must refer to the Reference Design (Test board) for the particular module.

For Example: TE0728 Reference Designs

Notes

Page properties
hiddentrue
idComments

In this Section you must refer to the Resources Page for the particular module.

For Example: TE0728 Resources





Scroll Only


HTML
<style>
.wiki-content .columnLayout .cell.aside {
width: 0%;
}</style>



Scroll pdf ignore


Custom_fix_page_content

Table of contents

Table of Contents
outlinetrue