Versions Compared

Old Version 23

changes.mady.by.user Antti Lukats

Saved on

compared with

New Version Current

changes.mady.by.user Thorsten Trenz

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
CompanyTrenz Electronic Gmbh
PCN Number

...

PCN-
201406xx
20140730
TitleTE0720-01 to TE0720-02
SubjectTrenz Electronic
TE0720 SoM
TE0720 SoM (system on module): revision 1 to revision 2 upgrade
Change Level
Issue Date

major

Issuer

Trenz Electronic GmbH

Place

Bünde, Germany, EU

20140730

Products Affected

This change affects all Trenz Electronic TE0720 SoMs of the first revision: TE0720-01-*.

affected product

suggested upgrade

TE0720-01-

1CF

*

TE0720-02-

1CF
TE0720-01-1CF1TE0720-02-1CF
TE0720-01-1CRTE0720-02-1CR
TE0720-01-2EFTE0720-02-2EF
TE0720-01-2ERcontact us
TE0720-01-2IFTE0720-02-2IF
TE0720-01-2IFC1TE0720-02-2IF
TE0720-01-2IFC2TE0720-02-2IF

Description of Change

*

Changes

#1

enhancement:

JTAG only boot mode

(question)

is now supported

.

Type: Enhancement

Reason: Enhancement of functionality

Impact: None

#2

enhancement:

Winbond W25Q256FV SPI Flash memory replaced with Spansion S25FL256

Type: Enhancement

Reason: Spansion S25FL256 is supported by current Xilinx design tools (ISE14.

replacement:

7, Vivado) W25Q256 is only supported by u-boot, Linux and Vivado SDK Programmer

Impact: May have to re-evaluate applications that write to the SPI Flash

#3 Texas Instruments TPS51200 Sink/Source DDR Termination Regulator replaced with TPS51206

.

Type: BOM change

Reason: TPS51206 was changed due to BOM optimization

Impact: None

#4 Changed MDIO pullup from 10k to 4k7

.

Type: BOM change

: changed

Reason: Avoiding potential problems when PHY management bus is configured at high speeds

Impact: None

#5 Changed eMMC core supply from switched

3V

3.3Vout to 3.3Vin

no (question).

Type: Schematic change

Reason: eMMC startup timing improvement

Impact: None

#6 MAC EEPROM power changed from 3.3V to 1.8V

, no impact on user design.

Type: Schematic change

Reason: PCB and System Controller optimization

Impact: None

#7 I2C Multiplexing no longer needed (to select between RTC and MEMS), all I2C devices are on the same bus.

removal:

Type: Schematic change

Reason: Change to new type of MEMS with only one I2C

Impact: None (if the old GPIO based I2C mux is used it just has no effect now)

#8 ST LSM303DLM (e-compass: 3D accelerometer and 3D magnetometer) MEMS is no longer assembled

(footprint only).removal: removed

in standard assembly variants

Type: BOM change

Reason: ST LSM303DLM MEMS has been discontinued

Impact: None for designs that did not use the MEMS sensor, please contact us for customized BOM if necessary

#9 Removed test pads on top layer

.enhancement: increased

Type: Layout change

Reason: No longer needed as the System Controller factory programming is done during tests using main B2B Connectors

Impact: None (test pads only used at factory)

#10 Increased component clearance from mounting holes on bottom layer

.

Reason for Change

  1. Spansion S25FL256 is supported by current Xilinx design tools (ISE14.7, Vivado) W25Q256 is only supported by u-boot, linux and Vivado SDK Programmer.
  2. TPS51206 was changed due to BOM optimization.
  3. ST LSM303DLM MEMS has been discontinued.

Application Impact

  1.  

Proposed Countermeasures

  1.  

Type: Enhancement

Reason: Decreasing the possibility to damage the module with improper extraction methods

Impact: None

#11 System Controller in-system programming via B2B JTAG pins

Type: Enhancement

Reason: Enhancement for Factory tests and programming

Impact: None

#12 JM1 pin 89 has new function that enables System Controller JTAG Chain no impact for old designs that connect this pin to GND

Type: Enhancement

Reason: Enhancement for Factory tests and programming

Impact: None

Method of Identification

The model code and revision number (e.g. TE0720-01 or TE0720-02) are printed on the top side of the PCB.

Production Shipment Schedule

From June 2014.

Contact Information

If you have any questions related to this PCN, please contact Trenz Electronic's Technical Support at

Disclaimer

Any projected dates in this PCN are based on the most current product information at the time this PCN is being
issued, but they may change due to unforeseen circumstances.  For the latest schedule and any other information,
please contact your local Trenz Electronic sales office, technical support or local distributor.