Versions Compared

Old Version 31

changes.mady.by.user Pedram Babakhani

Saved on

compared with

New Version Current

changes.mady.by.user Martin Rohrmüller

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

The Trenz Electronic TEMB0005 is an industrial-grade a carrier for the module TEM00005. The carrier is equipped with a Gigabit LAN socket, a FTDI JTAG/UART to USB2.0 interfacesolution, three low speed and one high speed  speed CRUVI B2B Connectors, a PMod Connector, a pin header and  a FTDI.  Find more information in the FTDI sections.

Refer to http://trenz.org/temb0005-info for the current online version of this manual and other available documentation.

...

  • Modules
    • TEM0005
  • RAM/Storage
    • 2KB EEPROM
  • On Board
    Authentication IC
    • FT2232H FTDI
    • 4x User LEDs
    • 2x Push Buttons
    • 2x MEMS Oscillators
  • Interface
    • 1x Samtec Razor Beam (SS5) B2B Connector
    • 1x Samtec Razor Beam (SS4) B2B High Speed CRUVI Connector
    • 3x Samtec  Samtec Low Speed CRUVI Connectors
    • 1x PMod SMD (2x6) Connector
    • 1x SMD Header (1x6)
    • 1x RJ45 LAN Socket
    • 1x Micro USB2.0 Connector
  • Power
    • 5V Input Power Supply 
  • Dimension
    • 115 x 70 mm
  • Notes

...

Scroll Title
anchorFigure_OV_BD
titleTEMB0005 block diagram


Scroll Ignore
draw.io Diagram
borderfalse
diagramNameTEMB0005_OV_BD
simpleViewerfalse
width639
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth640
revision911


Scroll Only


Main Components

...

Scroll Title
anchorFigure_OV_MC
titleTEMB0005 main components


Scroll Ignore
draw.io Diagram
borderfalse
diagramNameTEMB0005_OV_MC
simpleViewerfalse
width639
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth641
revision67


Scroll Only


  1. SMD Header 6x1, J3
  2. RJ45 LAN Socket, J1
  3. B2B Connector, J11
  4. Barrel Jack, J4
  5. Green LEDs, D1...4
  6. User Push Button, S2
  7. PMod 2x6 SMD Host Socket, J9
  8. FT2232H FTDI, U1
  9. Reset Push Button, S1
  10. Micro USB2.0 Socket, J2
  11. Red LED (PG_DCDC), D8
  12. Green LED (5VIN), D5
  13. High Speed CRUVI Connectors, J5
  14. Low Speed CRUVI Connectors, J8
  15. Low Speed CRUVI Connectors, J7
  16. Low Speed CRUVI Connectors, J6

...

Scroll Title
anchorTable_OV_RST
titleReset process.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Signal

B2BConnected toNote

RESET

J11- 54B2B, J5General Reset
M_RESETJ11- 11Push Button, S1Module Reset

Signals, Interfaces and Pins

EN_VADJJ11-110DCDC, U6pull-down, input from module
SEL_VADJJ11-108DCDC, U6

pull-up, input from module.
'low' → 1.8V,
'high'→ 2.5V


Signals, Interfaces and Pins

Page properties
hiddentrue
Page properties
hiddentrue
idComments

Notes :

  • For carrier or stand-alone boards use subsection for every connector type (add designator on description, not on the subsection title), for example:
    • SD
    • USB
    • ETH
    • FMC
    • ...
  • For modules which needs carrier use only classes and refer to B2B connector if more than one is used, for example
    • JTAG
    • UART
    • I2C
    • MGT
    • ...

...

MODE
Scroll Title
anchorTable_SIP_B2B
titleGeneral B2B connectors information

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorsInterfaceI/O Signal CountConnected toNotes
J11






JTAG4x Single EndedFTDI, U1
GPIO

MSIOD24x Single Ended, 12x Differential PairsCRUVI B2B, J5A0...5, B0...5 (N/P)
MSIO/GPIO8x Single EndedCRUVI B2B, J6A_X0...7
GPIO
MSIO8x Single EndedCRUVI B2B, J7B_X0...7
MSIO/GPIO8x Single EndedCRUVI B2B, J8C_X0...7
LEDs (2x MSIO, 2x MSIO/GPIO)4x Single EndedD1...4LED1...4
I/O
MSIO8x Single EndedPmod Header, J9
Push
Buttons
Button
2x
1x Single EndedPush Button, S1
-S2
M_RESET
Push Button1x Single EndedPush Button, S2pull-up, User Button
MSIO/GPIO/I2C
4x
2x Single EndedCRUVI B2B
,
J6
-J5
2x
I2C
Channels
ETH
4x Single Ended, 2x

2x Differential Pairs

2x Single Ended

RJ45 Socket,

J1A

J1

RJ45 LEDs,

J1B-J1C

2x LAne Transmit and Receive

J1


Yellow and Green LEDs

UART2x Single EndedFTDI, U1UART RX/TX
FTDI I/O2x Single EndedFTDI, U1BDBUS2-BDBUS3
CLK

1x Single Ended

1x Single Ended

Oscillator, U8

Oscillator, U8

30 MHz

MSIOD

4x Single Ended

CRUVI B2B, J5

RESET, HSIO, HSO, HSI

IO (3x MSIO, 4x MSIO/GPIO, 2x MSIO GPIO/I2C)9x Single EndedCRUVI B2B, J5

30 MHz

Reference Clock

Reset

1x Single Ended

1x Single Ended

CRUVI B2B, J5

Push Button, S1

RESET

M_RESET


Power Signal1x Single Ended

RED LED, D8


PG_DCDC
SC_SPI4x Single Endedpin header, J3SC_CLK, SC_SDO, SC_SDI, SC_SS
GOLDEN1x Single Ended
CRUVI B2B
Testpoint,
J5
TP1
GPIOPower Signal
GOLDEN
7x Single EndedCRUVI B2B, J5
JTAGSEL
1x Single Ended
RED LED, D8
Testpoint, TP2JTAGSEL


CRUVI B2B Connectors

The TEMB0005 is equipped with three Low Speed Connectors J6...8 and a High Speed Connector J5. These connectors are provided for CRUVI extension cards. More information is provided in the  B2B Connectors section.

Scroll Title
anchorTable_SIP_CRUVIB2B
titleCRUVI B2B connectors information

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

SpeedDesignatorsSchematicConnected toNotes
LowJ6A_X0...1B2B, J11alternative GPIO

A_X2...5B2B, J11
SC
alternative SPI

A_X6...7B2B, J11alternative I2C0 SDA/SCL
J7B_X0...7|B2B, J11
GPIO

J8C_X0...7B2B, J11alternative GPIO
HighJ5A0...A5 (N/P)B2B, J11HS I/O
B0...B5 (N/P)B2B, J11
MODEB2B, J11
HS I/O
HSIO, HI, HO, RESETB2B, J11HS I/O single ended

SMB_ALERT

, SMB_SDA

HSIO, HI, HOB2B, J11

, SMB_SCL, MODE, REFCLK

B2B, J11
DI,DO,SCK,SELB2B, J11
SPI
alternative GPIO


USB2.0 Socket

There is a USB2.0 Socket, J2 provided in order to communicate with the use JTAG/UART via FTDI, U1. Data signals from USB2.0 are passed through a Line Filter L1 and a Diode U2 in order to be protected against inverse polarity connection.

Scroll Title
anchorTable_SIP_USB2
titleUSB2.0 Socket information

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Pin SchematicConnected toNotes
IDN.CN.C
D+DL_PFTDI, U1Through Line Filter, L1
D-DL_NFTDI, U1Through Line Filter, L1
VbusVBUSDiode, U2


...

Scroll Title
anchorTable_OBP
titleOn board peripherals

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Chip/InterfaceDesignatorNotes
FTDIU1
LEDs105698017D1...D5D6
Push ButtonsS1-S2
EEPROM105698017U3
Oscillator
U4-, U8


FTDI FT2232H

The FTDI chip (U1U8) converts signals from USB2 to variety of standard serial and parallel interfaces. Refer to the FTDI data sheet to get information about the capacity of the FT2232H chip which is used in  Multi-Protocol Synchronous Serial Engine (MPPSE) mode for JTAG. 

The configuration of FTDI FT2232H chip is pre-programmed on the EEPROM U3U10.

Scroll Title
anchorTable_OBP_FT2232H
titleFTDI chip interfaces and pins

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

PinSchematicConnected toNotes
ADBUS0TCKB2BFPGA Bank 1B, J11U6JTAG interface
ADBUS1TDIB2BFPGA Bank 1B, J11U6
ADBUS2TDOB2BFPGA Bank 1B, J11U6
ADBUS3TMS

B2BFPGA Bank 1B, J11U6

BDBUS0UART1F_UART_RXDTXB2BFPGA Bank 1B, J11U6UART transmitter output
BDBUS1UART1F_UART_TXDRXB2BFPGA Bank 1B, J11U6UART receiver input
BDBUS2BDBUS2B2B,J11I/O
BDBUS3BDBUS3B2B,J11I/O
OSCIOSCIOscillator, U4Clock 12 MHz
EECSEECSEEPROM, U3EEPROM Contains FTDI configuration
EECLKEECLKEEPROM, U3
EEDATAEEDATAEEPROM, U3
DM/DPD_N/ D_PMicro USB, J2USB to UART
nRESET3.3V3.3V


...

Scroll Title
anchorTable_OBP_BTN
titleOn-board Push Buttons

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorSchematicConnected toFunctionalityNote
S1M_RESETB2B, J11Reset
S2ButtonBUTTONUser ButtonPower Status LED


LEDs

There are 4 green LEDs provided as user LEDs.

Scroll Title
anchorTable_OBP_LED
titleOn-board LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorColorConnected toActive LevelNote
D1...D4GreenB2B, J11Active HighUser LEDS
D5Green5VINActive HighPower Status LED
D6RedPG_DCDCActive Lowfrom module



Clock Sources

Scroll Title
anchorTable_OBP_CLK
titleOsillators

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorDescriptionFrequencyNote
U4MEMS Oscillator12 MHz
U8MEMS Oscillator30 MHz


...

Scroll Title
anchorFigure_PWR_PD
titlePower Distribution


Scroll Ignore
draw.io Diagram
borderfalse
diagramNameTEMB0005_PWR_PD
simpleViewerfalse
width639
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth641
revision2


Scroll Only


...

Scroll Title
anchorFigure_PWR_PS
titlePower Sequency


Scroll Ignore

draw.io Diagram
borderfalse
diagramNameTEMB0005_PWR_PS
simpleViewerfalse
width639
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth641
revision67


Scroll Only


Power Rails

Scroll Title
anchorTable_PWR_PR
titleModule power rails.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Power Rail Name

B2B Connector J11 Pin

CRUVI Connector J5 Pin

B2B Connector J6 Pin

B2B Connector J7 Pin

B2B Connector J8 PinDirectionNotes
3.3V1, 2, 3, 4-101010Output
VDAJ2236---Output
5VIN--121212Output


...

Page properties
hiddentrue
idComments
  • This section is optional and only for modules.

  • use "include page" macro and link to the general B2B connector page of the module series,

    For example: 6 x 6 SoM LSHM B2B Connectors

    Include Page
    PD:6 x 6 SoM LSHM B2B ConnectorsPD:
    6 x 6 SoM LSHM B2B Connectors

Include Page
DRAFT:3.1 x 5.6 SoM ST5/SS5 B2B Connectors
DRAFT:3.1 x 5.6 SoM ST5/SS5 B2B Connectors

...

Scroll Title
anchorTable_TS_ROC
titleRecommended operating conditions.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

ParameterMinMaxUnitsReference Document
VIN4.065.58VSee the carrier datasheets.
T_OPT-4508570°CSee the FTDI Push button datasheet.


Physical Dimensions

  • Module size: 115 mm × 70 mm.  Please download the assembly diagram for exact numbers.

  • Mating height with standard connectors: 4 mm.

...

Scroll Title
anchorFigure_TS_PD
titlePhysical Dimension


Scroll Ignore
draw.io Diagram
borderfalse
diagramNameTEMB0005_TS_PD
simpleViewerfalse
width639
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth641
revision2


Scroll Only
scroll-pdftrue
scroll-officetrue
scroll-chmtrue
scroll-docbooktrue
scroll-eclipsehelptrue
scroll-epubtrue
scroll-htmltrue


...

Scroll Title
anchorFigure_RV_HRN
titleBoard hardware revision number.


Scroll Ignore
draw.io Diagram
borderfalse
diagramNameTEMB0005_RV_HRN
simpleViewerfalse
width200
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth167
revision4


Scroll Only


...