...
If you write the character "a" the RAM test should start.
XMD procedure
Scroll Title |
---|
title | In the XMD console you should write "connect mb mdm -debugdevice cpunr 1". |
---|
|
Image Added |
In the XMD console you shoud write "rst" and then click "return" on the keyboard.
Scroll Title |
---|
title | In the XMD console you should write "dow C:/XilinxProject/reference-TE0300/SDK/SDK_Workspace/demo/Debug/demo.elf" and then click "return" on the keyboard. |
---|
|
Image Added |
Scroll Title |
---|
title | In the XMD console you shoud write "run" and then click "return" on the keyboard. |
---|
|
Image Added |
Scroll Title |
---|
title | In the XMD console you shoud write "terminal -jtag_uart_server 4321" and then click "return" on the keyboard. |
---|
|
Image Added |
After this you should open some terminal emulators (because If you want to input/output some characters to with the XMD UART), then open some terminal emulators, such as
- Microsoft / Hilgraeve HyperTerminal (usually included in Windows before Vista START MENU > All programs > Acessories > Communications > Hyper Terminal).
- ClearTerminal (very easy)
Tip |
---|
Connect using the following settings: - No Host address
- Port Number: 4321
- TCP/IP connection type (client)
|
Tip |
---|
The UART settings (not required by ClearTerminal) are: - bits per seconds: 115,200
- data bits: 8
- parity: none
- stop bits: 1
- flow control: none (otherwise you will not be able to enter commands)
|
Method A) XMD console, automatic
- Configure Jtag_Uart using "Debug" > "Debug Configuration"
- Modify xmd.ini
- Run XMD console using "Debug" > "Launch XMD"
- Run ClearTerminal Console
Method B) Manual
- Configure debug
- Change perspective from programming to debug selecting "Window" > "Open Perspective" > "Debug"
...
In the XMD console you shoud write "stop" and then click "return" on the keyboard.
In the XMD console you shoud write "run" and then click "return" on the keyboard.
After this two further step the menu of "demo.elf" should appear in the terminal emulator.
Scroll Title |
---|
title | After this two further step the menu of "demo.elf" should appear in the terminal emulator. |
---|
|
Image Added |
In the console the menu of demo.elf should appear. If the menu doesn't appear you have probably set RS232 instead of debug (mdm) and/or set incorrectly "Stdio output".
If you write the character "a" the RAM test should start.
Scroll Title |
---|
title | If you write the character "a" the RAM test should start. |
---|
|
Image Added |
Use the demo project without the XMD UART
To use the demo project without the XMD UART, you need to use "RS232" instead of "debug_module" as standard in/out port. Otherwise the application running on the Microblaze processor freezes if you disconnect the XMD. To accomplish that you need to set up the Microblaze "Software Platform Settings".
- In the dialog window select "OS and libraries" in the left window and pick "RS232" as a stdout and stdin interface.
- Then rebuild the software and download again the project to the FPGA.
The UART is then redirected to external pins, which are defined in the data/system.ucf file.
Tip |
---|
The UART settings are: - bits per seconds: 115,200
- data bits: 8
- parity: none
- stop bits: 1
- flow control: none (otherwise you will not be able to enter commands)
|
The following snippet shows the case of the TE0300 series modules:
Module RS232 constraints*
Net fpga_0_RS232_RX_pin LOC=B13;
Net fpga_0_RS232_TX_pin LOC=B14;
Please refer to the table below for other module series relevant to this application note.
Scroll pdf title |
---|
title | Location of UART pins examples. |
---|
|
TE series | RS232_RX FPGA ball | RS232_RX module pin | RS232_TX FPGA ball | RS232_TX module pin |
---|
TE0300 | R6 | J5-29 | P6 | J5-31 |
---|
TE0320 | V17 | J5-IO18 | W17 | J5-IO19 |
---|
TE0630 | Y7 | J5-29 | AB7 | J5-31 |
---|
TE0303 | It doesn't apply | J1-33 | It doesn't apply | J1-34 |
---|
TE0304 | It doesn't apply | J1-3 | It doesn't apply | J1-2 |
---|
TE0323 | It doesn't apply | J4-35 | It doesn't apply | J4-37 |
---|
host (PC) | TX | TX | RX | RX |
---|
|
Scroll Title |
---|
title | Sample UART to USB virtual COM port converter. |
---|
|
Image Added |
Scroll Title |
---|
title | Sample UART to USB virtual COM port converter: signal detail for TE0320 and TE0323. |
---|
|
Image Added |