Page History
...
Company | Trenz Electronic GmbH |
---|---|
PCN Number | PCN-20240611 |
Title | TEBF0808-04A to TEBF0808-05 Hardware Revision Change |
Subject | Hardware Revision Change |
Issue Date | 2024-06-11 (!!!)08-20 |
Products Affected
This change affects all Trenz Electronic TEBF0808 SoMsCarrier: TEBF0808-04A*.
Affected Product | Replacement |
---|---|
TEBF0808-04A | TEBF0808-05 |
...
Changes
...
#1 Restructured input power supply circuit architecture. Power supply can be supplied either via power path ATX connector (J20) (signal "12V_input_A") → fuse 0451007.MRL (F1) (signal "12V_input_A_Fused") → protection circuit LTC4365ITS8#TRMPBF (U52) with MOSFET Si7114ADN-T1-GE3 (T2, T3) (signal "12V") or via power path power jack (J25) (signal "12V_input_B") → fuse 0451007.MRL (F2) (signal "12V_input_B_Fused") → protection circuit LTC4365ITS8#TRMPBF (U53) with MOSFET Si7114ADN-T1-GE3 (T4, T5) (signal "12V"). Added input power protection circuit with TVS diode SMBJ20CA (D11, D19).
Type: Schematic Change
Reason: Improve power supply architecture.
Impact: None.
...
Power supplies are separated. It is not possible to supply the board simultaneously with both connectors (J20, J25) at the same time. It is not possible to supply one connector and draw power from the other connector.
#2 Changed DCDC EN5335QI (U8) to MPM3650CGQW-Z and adapted power circuit.
Type: Schematic Change
Reason: Harmonize with TEBF0818 seriesEOL of Component.
Impact: NonePower supply selection option 1.25 V removed. Increased output current capability. Minor changes in electrical characteristics.
...
#3 Changed DCDC EN6347QI (U19) to MPM3650CGQW-Z and adapted power circuit.
Type: Schematic Change
Reason:Harmonize with TEBF0818 series EOL of Component.
Impact: None. Increased current output capability. Minor changes in electrical characteristics.
...
#4 Changed DCDCs 171050601 (U22, U26, U29) to MPM3650CGQW-Z and adapted power circuit.
Type: Schematic Change
Reason: Harmonize with TEBF0818 seriesBOM Optimization.
Impact: None.
#1 Removed pull-up resistor (R107, R108, R117, R118, R124, R127) for SFP+ connector (J14).
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
...
Minor changes in electrical characteristics.
#5 Changed DCDC 171050601 (U18) to MPM3683GMN-10 and adapted power circuit.
Type: Schematic Change
Reason: EOL of ComponentBOM Optimization.
Impact: Power supply option 1.25 V removedNone. Increased current output capability. Minor changes in electrical characteristics. (???)
...
#6 Changed
...
DCDCs EN5311QI (U28, U43) to
...
MP2164GG-
...
Z and adapted power circuit.
Type: Schematic Change
Reason:BOM Optimization EOL of Component.
Impact: (???)
...
None. Increased current output capability. Minor changes in electrical characteristics.
#7 Changed load switch TPS27082LDDCR (Q1, Q2, Q3) to MP5077GG
...
-Z and adapted
...
circuit.
Type: Schematic Change
Reason:BOM Optimization.
Impact: (???)
#2 Changed DCDC EN6347QI (U19) to MPM3650CGQW-Z and adapted power circuit.
Type: Schematic Change
Reason: EOL of Component BOM Optimization.
Impact: None. Increased current output capability. Minor changes in electrical characteristics. (???)
#2 Changed DCDC EN5311QI (U28, U43) to MP2164GG-Z and adapted power circuit.
Type: Schematic Change
Reason: EOL of Component.
Impact: None. Increased current output capability. Minor changes in electrical characteristics. (???)
#2 Changed battery power supply circuit (U37, D16).
Type: Schematic Change
Reason: Change battery voltage supply from 1.8 V to 1.2 V to follow AMD recommendation.
Impact: (???)
...
#8 Changed battery power supply circuit architecture. Changed LDO (U37) from TPS780180300 to TPS7A0212PDBVR and diode (D16) from SDMG0340LC-7-F to BAS70-05W.
...
Type: Schematic Change
Reason: (???)
Impact: (???)
...
Added capacitor (C278), resistor (R269), and assembly option (default: not fitted) resistor (R270).
Type: Schematic Change
Reason: BOM OptimizationFollow AMD recommendation.
Impact: None. Increased current output capability. Minor changes in electrical characteristics. (???)
...
Reduced voltage level for signal "PSBATT" from 1.8 V to 1.2 V.
#9 Reordered MGT signal connection at each FireFly connector (J6, J21) separately.
Type: PCB Schematic Change
Reason: Follow PCIe recommendationImprove FireFly handling and harmonize with TEBF0818 series.
Impact: None.
...
FireFly using custom firmware needs to be adapted by customer.
#10 Changed eMMC (U2) from MTFC4GACAJCN-4M IT to SDINBDG4-8G-XI2.
Type:PCB Change Schematic change
Reason:Improve signal integrity EOL of Component.
Impact:None.
#3 Changed CAN bus signals net names (CAN_H → CAN_P, CAN_L → CAN_N) to route them with 120 Ohm differential impedance.
Type: PCB Change
Reason: Improve signal integrity.
Impact: None.
#3 Reordered MGT signal connection at FireFly connector (J6, J21).
Type: Schematic Change
Reason: Improve FireFly handling and harmonize with TEBF0818 series.
Impact: If FireFly is used custom firmware needs to be adapted by customer.
#3 Renamed following signals (IN2_P → IN2_CLK_P and IN2_N → IN2_CLK_N).
Type: Schematic Change
Increased eMMC memory density from 4 GByte to 8 GByte.
#11 Restructered PCIe clock system tree. Differential clock (signals "CLK0_N" and "CLK0_P") coming from connector (J2) is distributed via new added fanout buffer NB3L202KMN (U56) to PCIe connector (J11) (signals "PCI_REF_P" and "PCI_REF_N") and B2B connector (J2) (signals "B505_CLK0_P" and "B505_CLK0_N"). Removed clock oscillator DSC1123CI2-100.0000T (U6).
Type: Schematic Change
Reason: Changed PCIe clock to HCSLReason: Harmonize with TEBF0818 series.
Impact: None.
...
#12 Changed AC coupling (C93/C94 [REV04A]) to DC coupling (R263/R264 [REV05]) for differential clock signals "CLK0_N" and "CLK0_P". Removed capacitor (C94).
Type: Schematic Change
Reason: Change voltage level between CPLD voltage rail "3V3SB" and ATX connector voltage rail "5VSB"Changed PCIe clock to HCSL.
Impact: None.
...
#13 Changed MEMS oscillator (U10) from SiT8008AI-73-XXS-52.000000E to SiT8008BI-73-XXS-52.000000E.
Type:Schematic Change BOM change
Reason:Change voltage level between CPLD voltage rail "3V3SB" and ATX connector voltage rail "5VSB" and harmonize with TEBF0818 series EOL of Component.
Impact: None. CPLD firmware reflects it but customer firmware needs to be checked/adapted by customer.
...
Clock revision changed.
#14 Changed power supply for SFP+ connector (J14) from power rail "3.3V_PCI" to power rail "3.3V_PER".
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
...
#15 Removed pull-up resistor (R107, R108, R117, R118, R124, R127) for SFP+ connector (J14).
Type: Schematic Change
Reason: Harmonize with TEBF0818 series. (???)BOM Optimization.
Impact: None.
...
Resistors were not fitted on previous revision.
#16 Changed pull-up resistor voltage for resistor (R18, R21, R86, R87, R113 ... R115, R121 ... R123).
Type: Schematic Change
Reason: Improve ESD protectionHarmonize with TEBF0818 series.
Impact: None.
...
#17 Inserted level shifter circuit (T7, T8) between CPLD (U39) (signal "PWROK") and ATX connector (J20) (signal "PWR_OK").
Type: Schematic Change
Reason: Harmonize with TEBF0818 seriesFix voltage level for signal "PWROK".
Impact: None.
#1 Change eMMC (U2) from MTFC16GJVEC-2M WT to SDINBDG4-8G-XI2.
Type: BOM change
Reason: EOL of Component.
Impact: None. Replacement has same capacity as used on corresponding affected variant. Reference designs for vivado versions 2019.2 and 2020.2 were tested and work properly without any changes. (???)
#17 Changed resistor (R14) from 4.99 kOHm to 2 kOhm.
Type: BOM Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#28 Added testpoint (TP17, TP20 ... TP22).
Type: Schematic Change
Reason: Voltage and system monitoring improvement. (???)
Impact: None.
#12 Changed LED (D8, D10) from 150060VS75000 to 19-213/G6C-BM1N2/DT.
Type: Schematic Change
...
Impact: None.
#1 Changed Fan F455B-05LD (M1) to Fan MF40060V2-1000U-A99 (MP1) and updated according mechanical screws and nuts.
Type: BOM change
Reason: EOL of Component.
Impact: Specified airflow of fan decreases slightly from 0.03 m³/min to 0.028 m³/min. (???)
#12 Added assembly option (default: not fitted) for cooling solution with fan controller LM96163CISD/NOPB (U54), temperature sense MMBT3904 (T12), and AND Gate (U55)
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#12 Connected fan controller LM96163CISD/NOPB (U54) to I2C bus (signals "SC_SCL" and "SC_SDA").
Type: Schematic Change
...
Change voltage level between CPLD voltage rail "3V3SB" and ATX connector voltage rail "5VSB" for signal "PWROK".
#18 Inserted MOSFET (T9) circuit for level shifting and logic level inverting between CPLD (U39) (signal "PSON") and ATX connector (J20) (signal "PS_ON_N").
Type: Schematic Change
Reason: Fix voltage level for signal "PSON".
Impact: None. Change voltage level between CPLD voltage rail "3V3SB" and ATX connector voltage rail "5VSB" for signal "PSON". Change logic level for signal "PSON". CPLD firmware reflects it but customer firmware needs to be checked/adapted by customer.
#19 Connected all shield signals for connector (J7) together to net "FGND". Removed shield signals (J7) from net "F2GND". Removed capacitor (C261).
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#20 Renamed shield net to FGND2 for connector (J13) and changed shield components from 0 Ohm resistor (R43, R44 [REV04A]) to 1 MOhm resistor (R143 [REV05]) and 100 pF capacitor (C149 [REV05]). Removed resistor (R44 [REV04A]).
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#21 Inserted FGND3 with resistor (R43 [REV05]) and capacitor (C93 [REV05]) for SFP+ connector (J14) shield.
Type: Schematic Change
Reason: Improve ESD protection.
Impact: None.
#22 Changed Fan F455B-05LD (M1) to Fan MF40060V2-1000U-A99 (MP1) and updated according mechanical screws, nuts, crimp contacts, and housing (JX1).
Type: BOM change
Reason: EOL of Component.
Impact: Specified airflow of fan increases from 0.028 m³/min to 0.155 m³/min. Specified acoustic noise increases from 20 dB(A) to 25.3 dB(A). Increased temperature range from (-10 °C - +60 °C) to (-10 °C - +70 °C).
#23 Added assembly option (default: not fitted) for cooling solution with fan controller LM96163CISD/NOPB (U54), temperature sense MMBT3904 (T12), and AND Gate (U55).
Type:
Impact: None. For assembled fan controller I2C address 0x4C is used.
#12 Changed pin header (J19) from two pins to four pins.
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None. Consider to use correct pins.
...
#24 Connected fan controller LM96163CISD/NOPB (U54) to I2C bus (signals "SC_SCL" and "SC_SDA").
Type: PCB change Schematic Change
Reason:Improve module orientation visibilityFan controller handling.
Impact: None. Assembled fan controller uses I2C address 0x4C.
...
#25 Changed pin header (J19) from two pins to four pins.
Type: Schematic Change
Reason:Use external pull-up resistor Harmonize with TEBF0818 series.
Impact: None.
...
#26 Used resistor (
...
R164) as pull-up resistor for signal "POK_1V8".
Type: Schematic Change
Reason: Harmonize with TEBF0818 seriesUse external pull-up resistor.
Impact: None.
...
#27 Added debounce circuit (R235, C211) for button (S1) and (R236, C213) for button (S2).
Type: Schematic Change
Reason: Harmonize with TEBF0818 seriesImprove button behaviour.
Impact: None.
...
#28 Added pull-up resistor (
...
R228 ... R234) for signal ("PRSNT1", "PERST", "WAKE", "PRSNT2", "PRSNT3", "PRSNT4", "PRSNT5").
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#29 Added pull-up resistor (R293) for signal "I2C_RST".
Type: Schematic Change
Reason: Use external pull-up resistor.
Impact: None.
#30 Added termination resistor assembly option (R134) for differential clock (signals "CLK0_N" and "CLK0_P").
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#31 Changed LED (D8, D10) from 150060VS75000 to 19-213/G6C-BM1N2/DT.
Type: Schematic Change
Reason:BOM Optimization.
Impact: None.
#32 Changed 1 µH power inductor (L1) from 1.7 A, 20 %, 55 mOhm to 0.7 A, 5 %, 620 mOhm.
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#33 Changed power inductor (L2, L6, L13, L14) from 1 µH, 1.7 A, 55 mOhm to 3.3 µH, 1.5 A, 162 mOhm.
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#34 Changed power inductor (L8, L9, L11, L12) from 1 µH, 1.7 A, 55 mOhm to 4.7 µH, 1.5 A, 84 mOhm.
Type: Schematic Change
Reason: Follow SFP+ recommendation.
Impact: None.
#35 Changed ferrid bead (L16, L17) from BKP0603HS121-T to MPZ0603S121HT000.
Type: BOM Change
Reason:EOL of component.
Impact: None.
#36 Changed 33 nF capacitor (C192) from 50 V, 0603 to 25 V, 0402.
Type: Schematic Change
Reason: BOM Optimization.
Impact: None.
#37 Changed capacitor (C121 ... C124, C179, C182, C185, C221 ... C223) from 100 nF, 6.3 V, X5R to 10 nF, 10 V, X7R.
Type: Schematic Change
Reason: Follow AMD recommendation.
Impact: None.
#38 Changed capacitor (C197, C200, C202, C203) from 100 nF, 6.3 V, X5R to 10 nF, 10 V, X7R.
Type: Schematic Change
Reason: Follow SATA recommendation.
Impact: None.
#39 Changed capacitor (C69, C70) from 100 nF, 6.3 V, 0201 to 220 nF, 50 V, 0402.
Type: Schematic Change
Reason: Follow PCIe recommendation.
Impact: None.
#40 Changed 220 nF capacitor (C170) from 16 V, X7R to 50 V, X5R.
Type: Schematic Change
Reason: BOM Optimization.
Impact: None.
#41 Changed capacitor (C47, C50, C52, C57, C60, C62) from 470 nF, 6.3 V, 0402 to 100 nF, 10 V, 0201.
Type: Schematic Change
Reason: Follow SFP+ recommendation.
Impact: None.
#42 Changed 470 nF capacitor (C220) from 0201 to 0402.
Type: Schematic Change
Reason: BOM Optimization.
Impact: None.
#43 Changed capacitor (C39, C82, C207) from 4.7 µF, 6.3 V to 10 µF, 10 V.
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#44 Changed capacitor (C49, C51, C59, C61) from 10 µF, 6.3 V, 0603 to 22 µF, 25 V, 0805.
Type: Schematic Change
Reason: Follow SFP+ recommendation.
Impact: None.
#45 Changed capacitor (C48, C58) from 10 µF, 6.3 V, 0603 to 100 nF, 10 V, 0201.
Type: Schematic Change
Reason: Follow SFP+ recommendation.
Impact: None.
#46 Changed 10 µF capacitor (C11, C12, C13, C15, C18, C20, C34, C63, C136, C204, C239) from 6.3 V to 10 V.
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#47 Changed capacitor (C42, C67) from 47 µF, 6.3 V, 1206 to 22 µF, 25 V, 0805.
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
#48 Changed capacitor (C72, C73) from 100 µF, 6.3 V, 20 % to 22 µF, 25 V, 10 %.
Type: Schematic Change
Reason: Increased voltage rating.
Impact: None.
#49 Changed 33 Ohm resistor (R7, R13, R19, R68, R103, R112, R128, R151, R168, R189) from 63 mW, 0402 to 50 mW, 0201.
Type: Schematic Change
Reason: Improve signal integrity.
Impact: None.
#50 Changed resistor (R101, R102, R104, R105) from 249 Ohm to 240 Ohm
...
Type: Schematic Change
Reason: Enable OTG capability.
Impact: None. (???)
#1 Restructered PCIe clock system tree. Differential clock (signals "CLK0_N" and "CLK0_P") is distributed via new added fanout buffer NB3L202KMN (U56) to PCIe connector (J11) (signals "PCI_REF_P" and "PCI_REF_N") and B2B connector (J2) (signals "B505_CLK0_P" and "B505_CLK0_N"). Removed clock oscillator DSC1123CI2-100.0000T (U6).
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact:
...
.
Type: Schematic Change
Reason:Harmonize with TEBF0818 series BOM Optimization.
Impact: None.
...
#51 Changed resistor (
...
R40) from 4.99 kOhm to 0 Ohm.
Type: Schematic Change
Reason: Harmonize with TEBF0818 seriesSet HDMI Hot Plug level properly.
Impact: None.
...
#52 Changed
...
resistor (R27, R196) from 4.99 kOhm to 100 Ohm.
Type: Schematic Change
Reason:Follow AMD recommendation Harmonize with TEBF0818 series.
Impact: None.
...
#53 Changed
...
resistor (R14) from 4.99 kOhm to 2 kOhm.
Type: Schematic ChangeBOM Change
Reason:Follow SATA recommendation Harmonize with TEBF0818 series.
Impact: None.
...
#54 Changed pull-up resistor (R18, R21, R86, R87, R113, R114, R115, R121 ... R123) from 4.99 kOhm to 7.5 kOhm.
Type: Schematic Change
Reason: Follow PCIe recommendationHarmonize with TEBF0818 series.
Impact: None.
...
#55 Changed resistor (R41) from 4.99 kOhm to 200 kOhm.
Type: Schematic Change
Reason:Improve power quality Set HDMI Hot Plug level properly.
Impact: None.
...
#56 Changed resistor (R65) from 8.06 kOhm to 1 kOhm.
Type: Schematic Change
Reason: Improve power supply input protectionEnable OTG capability.
Impact: None.
...
#57 Added ferrid bead (L25) for fan power supply.
Type: Schematic Change
Reason: Harmonize with TEBF0818 seriesImprove power quality.
Impact: None.
...
#58 Added additional decoupling capacitor (C244, C254, C262, C263, C281 ... C287).
Type: Schematic Change
Reason: Follow SFP+ recommendationImprove power supply.
Impact: None.
...
#59 Added termination resistor (R277 ... R292).
Type: Schematic Change
Reason: Follow SFP+ recommendationImprove signal integrity for FireFly connector (J6, J21).
Impact: None.
...
#60 Set LDO TPS79901DRV (U47) and LDO related components, ferrid bead (L20), capacitor (C127) and resistor (R181) to not fitted.
Type: Schematic Change
Reason: Follow SFP+ recommendation BOM Optimization.
Impact: None.
...
#61 Set capacitor (
...
C16, C17) to not fitted.
Type: Schematic Change
Reason:Improve power supply Harmonize with TEBF0818 series.
Impact: None.
...
#62 Set resistor (
...
R98, R198) to not fitted.
Type: Schematic Change
Reason:Use external pull-up resistor Harmonize with TEBF0818 series.
Impact: None.
...
#63 Changed net name (IN2_P → IN2_CLK_P and IN2_N → IN2_CLK_N).
Type: Schematic Change
Reason:Improve power supply Harmonize with TEBF0818 series.
Impact: None.
...
#64 Changed net name from "5VSBIN" to "5VSB".
Type: Schematic Change
Reason:BOM optimization Harmonize with TEBF0818 series.
Impact: None.
...
#65 Changed net name from "3.3V_MOD" to "VCC_MOD".
Type: Schematic Change
Reason: Harmonize with TEBF0818 series.
Impact: None.
...
#66 Added
...
testpoint (
...
TP14,
...
TP16,
...
TP17, TP20 ... TP25).
Type: Schematic Change
Reason: Signal monitoring improvement.
Impact: None.
#67 Changed impedance controlled routing for differential PCIe signals (TX/RX) to 90 Ohm differential impedance.
Type: Schematic PCB Change
Reason: Improve button behaviourFollow PCIe recommendation.
Impact: None.
...
#68 Routed signals which are marked in schematics as "D100" with 100 Ohm differential impedance.
Type: Schematic PCB Change
Reason: Harmonize with TEBF0818 seriesImprove signal integrity.
Impact: None.
...
#69 Changed
...
CAN bus signal net names (CAN_H → CAN_P, CAN_L → CAN_N) to route them with 120 Ohm differential impedance.
Type: PCB Change
Reason: Improve signal integrity.
Impact: None.
#70 Updated PCB rules, PCB layout, and PCB layerstack.
Type: Schematic PCB Change
Reason: Harmonize with TEBF0818 seriesImprove board quality.
Impact: None.
...
#71 Added module orientation mark in silkscreen top side.
Type:Schematic Change PCB change
Reason: Harmonize with TEBF0818 seriesImprove module insertion process.
Impact: None.
...
#72 Added UKCA logo.
Type:Documentation Update PCB Change
Reason:Documentation improvement Required for export to UK.
Impact: None.
...
#73 Changed fiducials to standard fiducial type.
Type: Schematic Change
Reason: Improve routingUse standard fiducials.
Impact: None.
...
#74 Updated schematic sheets from template.
Type: PCB ChangeDocumentation Update
Reason: Required for export to UKDocumentation improvement.
Impact: None.
...
#75 Added legal notices, power overview, I2C address table, and power voltage range table. Updated block diagram and revision history. Updated page count and order.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.
#33 Updated schematic sheet from template.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.
#33 Updated block diagram.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.
#1
Type:
Reason:
Impact:
Scroll Pagebreak |
---|
Method of Identification
Production Shipment Schedule
Scroll Pagebreak |
---|
Method of Identification
draw.io Diagram | ||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Production Shipment Schedule
With immediate effect this change takes placeFrom XXXXX, after old stock is gone. If the new revision is not suitable for your application and still the former revision of the board is needed, please contact us.
...
Contact Information
If you have any questions related to this PCN, please contact Trenz Electronics Technical Support at
- forum.trenz-electronic.de
- wiki.trenz-electronic.de
- support%trenz-electronic.de (subject = PCN-JJJJMMDD20240611)
phone
national calls: 05741 3200-0
international calls: 0049 5741 3200-0
Disclaimer
Any projected dates in this PCN are based on the most current product information at the time this PCN is being issued, but they may change due to unforeseen circumstances. For the latest schedule and any other information, please contact your local Trenz Electronic sales office, technical support or local distributor.
...