Versions Compared

Old Version 6

changes.mady.by.user Fabio De Riccardis

Saved on

compared with

New Version Current

changes.mady.by.user Fabio De Riccardis

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Migrated to Confluence 5.3

Generation 2 to generation 3 migration (firmware + driver)

  video play list.

Migration from the second generation (aka DEWESoft) to the third generation (aka TE USB FX2) of Trenz Electronic USB FX2 technology stack (firmware and driver).

Widget Connector
width400
urlhttps://www.youtube.com/watch?v=Wmg6rms4bvc&list=PL_T7L7yrNs4nE5OD977Vt78Asy64xjZhf
height300

TE0300: migration from 2nd to 3rd generation (firmware + driver)

This video shows how to upgrade a Trenz Electronic TE0300 device form the second to the third generation (firmware and driver). The video has been recorded on a Microsoft Windows 7 (64 bit) operating system with a TE0300-01 FPGA module connected to a USB port, but the procedure is almost the same for any Trenz Electronic USB FX2 device.

In this video, power-on reset is used.

Please note that TE0300 has master reset, thus a powered reset (S2 switch) is possible.

Widget Connector
width400
urlhttps://www.youtube.com/watch?v=JUsjVEt4PqM&list=PL_T7L7yrNs4nE5OD977Vt78Asy64xjZhf
height300

TE0320: migration from 2nd to 3rd generation (firmware + driver)

This video shows how to upgrade a Trenz Electronic TE0320 device form the second to the third generation (firmware and driver). The video has been recorded on a Microsoft Windows 7 (64 bit) operating system with a TE0320 FPGA module connected to a USB port, but the procedure is almost the same for any Trenz Electronic USB FX2 device.

In this video, power-on reset is used.

Please note that TE0320 has master reset, thus a powerered reset ( S1D switch to ON) is possible.

Widget Connector
width400
urlhttps://www.youtube.com/watch?v=k3K6qJFxN6A&list=PL_T7L7yrNs4nE5OD977Vt78Asy64xjZhf
height300

TE0630: migration from 2nd to 3rd generation (firmware + driver)

This video shows how to upgrade a Trenz Electronic TE0630 device form the second to the third generation (firmware and driver). The video has been recorded on a Microsoft Windows 7 (64 bit) operating system with a TE0630-00 FPGA module connected to a USB port, but the procedure is almost the same for any Trenz Electronic USB FX2 device.

Please note that, unlike TE0300 and TE0320, TE0630-00 has no -master reset-, thus a power-on reset is required.

Widget Connector
width400
urlhttps://www.youtube.com/watch?v=9Y4rkbDc6lI&list=PL_T7L7yrNs4nE5OD977Vt78Asy64xjZhf
height300

Cypress USB Console used for 2nd to 3rd generation update.

This video explains how to use -Cypress USB Console- instead of "Cypress Control Center".

This video assumes that you have followed the first 6 minutes of "generation 2 to generation 3" videos (for anyone of the Trenz Electronic USB FX2 modules).

This video is an extension to 6:00 to 6:40 of "generation 2- to -generation 3" videos.