Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Page properties
hiddentrue
idComments

Note for Download Link of the Scroll ignore macro:


Scroll Ignore

Download PDF version of this document.


Scroll pdf ignore

Table of Contents

Table of Contents

...

The Trenz Electronic TE0716 is a commercial-grade* SoM (System on Module) based on Xilinx Zynq-7000 SoC XC7Z020*, with 1GB of DDR3L-1600 SDRAM*, 32MB of SPI flash memory, 10x 12-Bit Low Power SAR ADCs, 512Kb Serial EEPROM, Gigabit Ethernet PHY transceiver, an USB PHY transceiver, a single chip USB 2.0 to UART/JTAG Interface (Xilinx License included), and powerful switching-mode power supplies for all on-board voltages. A large number of configurable I/Os are provided via rugged high-speed board-to-board connectors.

Refer to http://trenz.org/te0716-info for the current online version of this manual and other available documentation.

Notes: * standard values but depends on assembly version. Additional assembly options are available for cost or performance optimization upon request.

Page properties
hiddentrue
idComments

Notes :

...

  • SoC/FPGA
    • Package: CLG484
    • Device: Xilinx Z-7020
    • Speed: -1 *
    • Temperature: C grade *.
  • RAM/Storage
    • Low Power DDR3 SDRAM on PS
      • Data width: 32bit
      • Size: def. 1GB *
      • Speed: 1600 Mbps **
    • QSPI boot Flash
      • Data width: 4bit
      • size: 32MB *
    • MAC address serial EEPROM with EUI-48™ node identity (Microchip 24AA025E48).
    • 512Kb user MAC address serial EEPROM.
  • On Board
    • 10x 12-Bit Low Power SAR ADCs up to 2 MSPS (NCD98011).
    • Low Power Oscillators.
    • Gigabit Ethernet PHY transceiver (Marvell Alaska 88E1512).
    • High-Speed USB 2.0 ULPI transceiver with full OTG support (Microchip USB3320C).
    • Single chip High-Speed USB 2.0 to UART/JTAG Interface (Xilinx License included) (FTDI FT2232H).
    • 2xUser RGB 2x User RGB LEDs (Green), LED FPGA "Done" (Green).
    • 2 x Tactile 2x Tactile Switches (User), 1 x Tactile Switche (Reset).
  • Interface
    • 120 x 120x HR PL I/Os (3 banks).
    • 2x PS MIOs (shared with UART TX/RX ZYNQ-FTDI).
    • 1 Gbps RGMII Ethernet interface.
    • High Speed USB 2.0 ULPI with full OTG support.
    • High Speed USB 2.0 to UART/JTAG interface, including microUSB-B connector.
    • microSD™
    • JTAG

...

Scroll Title
anchorFigure_OV_BD
titleTE0716-01 block diagram


Scroll Ignore

draw.io Diagram
borderfalse
diagramNameDB-TE0716-01
simpleViewerfalse
width
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth641
revision1719


Scroll Only



Main Components

...

Scroll Title
anchorTable_OV_IDS
titleInitial delivery state of programmable devices on the module

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Storage device name

IC Designator

Content

Notes

Quad SPI Flash

U7Empty

-

512Kb Serial EEPROMU21Empty

-

2Kb 24AA025E48 EEPROMU24Pre-programmed globally unique, 48-bit node address (MAC).-
4Kb M93C66-R EEPROMU40Xilinx JTAG Programmer License-For FTDI IC only (U39).



Configuration Signals

Page properties
hiddentrue
idComments
  • Overview of Boot Mode, Reset, Enables.

...

Scroll Title
anchorTable_SIP_JTG
titleJTAG pins connection

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

JTAG Signal

B2B Connector

Notes
TMSJP2-73.3V Voltage level. Also Connected to U39 (FTDI)
TDIJP2-113.3V Voltage level. Also Connected to U39 (FTDI)
TDOJP2-103.3V Voltage level. Also Connected to U39 (FTDI)
TCK

JP2-8

3.3V Voltage level. Also Connected to U39 (FTDI)

VREF_JTAGJP2-5Module Vout


UART Interface

...

Scroll Title
anchorTable_SIP_USB
titleUSB pins connection

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

USB Signal

B2B Connector

Notes
xx
USB_OTG_D_ PJP2-
x
643.3V Voltage level.
xx
USB_OTG_D_ NJP2-
x
653.3V Voltage level.
xx
USB_OTG_IDJP2-
x
663.3V Voltage level.
xx
USB_VBUS_E NJP2-
x
673.3V Voltage level.
xx
USB_VBUSJP2-
x
68
3.3V Voltage level.

Max. voltage: 5.5V


ETH Interface

The TE0716 provides ETH access to the TE0716 SoM through B2B connector JP1. The ETH interface is connected later to the Zynq Ethernet PS (Ethernet 0), by using a ETH PHY.

Scroll Title
anchorTable_SIP_ETH
titleETH pins connection

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

ETH Signal

B2B Connector

Notes
xx

PHY_MDI0_P

PHY_MDI0_ N

JP1-5

JP1-

x

4

3.3V Voltage level.
xx

PHY_MDI1_P

PHY_MDI1_ N

JP1-7

JP1-

x

8

3.3V Voltage level.
xx

PHY_MDI2_P

PHY_MDI2_ N

JP1-68

JP1-

x

67

3.3V Voltage level.
xx
3.3V Voltage level.xx

PHY_MDI3_P

PHY_MDI3_ N

JP1-

x

65

JP1-

x

64

3.3V Voltage level.


ADC Interface

The analog inputs of the ADCs are connected to B2B connector JP1.

...

The PWM signals are connected to B2B connector JP2. All this digital signals are connected to PL Bank 33 (except for PWM_6_H  and PWM_6_L which are connected to PL Bank 13). This These signals could be also used as normal single ended I/Os.

...

  • Part number: S25FL256SAGBHI20*
  • Supply voltage: 3.3V (2.7V - 3.6V).
  • Speed: 133MHz max.*
  • Temperature: Industrial Range -40°C to +85°C.

Notes: * standard number/value but depends on assembly version.

Scroll Title
anchorTable_OBP_SPI
titleQuad SPI interface MIOs and pins

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

MIO PinSchematicU7 PinNotes
MIO1SPI-CSCS#-
MIO3SPI-DQ1/M1SO/IO1-
MIO4SPI-DQ2/M2WP#/IO2-
MIO2SPI-DQ3/M3HOLD#/IO3-
MIO5SPI-DQO/M0SI/IO0-
MIO6SPI-SCK/M4SCK-


...

Scroll Title
anchorTable_OBP_I2C_EEPROM
titleI2C address for EEPROM

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

I2C DeviceI2C AddressDesignatorNotes
2K Serial EEPROMs with EUI-48™

0xA6 0x53 (write7bit)0xA7 (read)
0x53 (7bit)

U24U24-
512Kb Serial EEPROM

0xA0 (write)
0xA1 (read)
0x50 (7bit)

U21-


ADCs

The TE0716 module has 10x 12-Bit Low Power SAR Analog-to-Digital Converter, fully differential input, signed output, with SPI−compatible interface (NCD98011), which are connected to the FPGA PL BANK34.

...

Scroll Title
anchorTable_OBP_ADC
titleADC to PL interface PL and pins

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DesignatorSchematicPL PinNotes
U1

S0_CLK          

S0_CSN          

S0_OUT          

J18

J16

K18

3.3V Max Voltage on any pin.
U2

S5_CLK          

S5_CSN          

S5_OUT          

M21

T16

T17

3.3V Max Voltage on any pin.
U3

S1_CLK          

S1_CSN          

S1_OUT          

L18

J21

L19

3.3V Max Voltage on any pin.
U4

S6_CLK          

S6_CSN          

S6_OUT          

J22

K21

J20

3.3V Max Voltage on any pin.
U10

S2_CLK          

S2_CSN          

S2_OUT          

M22 

R21 

R20 

3.3V Max Voltage on any pin.
U11

S7_CLK          

S7_CSN          

S7_OUT          

L22 

M20 

M19 

3.3V Max Voltage on any pin.
U15

S3_CLK          

S3_CSN          

S3_OUT          

J17 

J15 

L17 

3.3V Max Voltage on any pin.
U16

S8_CLK          

S8_CSN          

S8_OUT          

M17 

N18 

N17 

3.3V Max Voltage on any pin.
U17

S4_CLK          

S4_CSN          

S4_OUT          

P17 

L21 

P18 

3.3V Max Voltage on any pin.
U19

S9_CLK          

S9_CSN          

S9_OUT          

K15 

P21 

P20 

3.3V Max Voltage on any pin.


...

Scroll Title
anchorTable_OBP_ETH
titleEthernet PHY to Zynq SoC connections

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

U8 Pin Signal NameConnected toSignal DescriptionNote

TX_CLK

ETH-TXCK        MIO16

RGMII Transmit Clock

-

TXD[0..3]

ETH-TXD0..3MIO17..20

RGMII Transmit Data

-

TX_CTRL

ETH-TXCTL       MIO21

RGMII Transmit Control

-

RX_CLK

ETH-RXCK        MIO22

RGMII Receive Clock

-

RXD[0..3]

ETH-RXD0..3MIO23..26

RGMII Receive Data

-

RX_CTRL

ETH-RXCTL       MIO27

RGMII Receive Control

-

MDC

ETH-MDCMIO52

Management data clock reference

-

MDIO

ETH-MDIOMIO53

Management data

-

RESETn

PHY-RST         MIO51, U18

Hardware reset. Active low.

Shared with U18 (RESETB) USB

MDIP[0..3] MDIN[0..3]

PHY_MDI0..3_P
PHY_MDI0..3_N
JP1

Media Dependent Interface

-

XTAL_IN

ETH-CLK         U9

Reference Clock Input

see also Clock Sources section

LED[0..1]

PHY_LED0..1FPGA BANK 33

LED output

-


...

Scroll Title
anchorTable_OBP_USB
titleUSB PHY to Zynq SoC connections

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

U18 Pin Signal NameConnected toSignal DescriptionNote

CLKOUT

OTG-CLK         MIO36ULPI Output Clock-

DATA[0..3]

OTG-DATA0..3MIO32..35

ULPI bi-directional data bus

-

DATA[4]

OTG-DATA4       MIO28ULPI bi-directional data bus -

DATA[5..7]

OTG-DATA5..7MIO37..39ULPI bi-directional data bus -

DIR

OTG-DIR         MIO29

Controls the direction of the data bus

-

STP

OTG-STP         MIO30

terminates transfers PHY input

-

NXT

OTG-NXT         MIO31

control data flow into and out of the PHY

-

RESETB

PHY-RST MIO51, U8reset and suspend the PHY. Active low.Shared with U8 (RESETn) Ethernet

DP

USB_OTG_D_PJP2-64

D+ pin of the USB cable

3.3V Voltage level

DM

USB_OTG_D_N     JP2-65

D- pin of the USB cable

3.3V Voltage level

ID

USB_OTG_ID      JP2-66ID pin of the USB cable3.3V Voltage level

CPEN

USB_VBUS_EN     JP2-67

Controls the external VBUS power switch

3.3V Voltage level

VBUS

USB_VBUS        JP2-68

For RVBUS connection

Max. voltage: 5.5V

REFCLK

OTG-RCLK        U14 

ULPI clock input

see also Clock Sources section


...

Scroll Title
anchorTable_OBP_FTDI
titleUSB FTDI to Zynq SoC connections

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

U39 Pin Signal NameConnected toSignal DescriptionNote
DPD_JTAG_PJ13-2USB Data Signal Plus3.3V Voltage level
DMD_JTAG_NJ13-3USB Data Signal Minus3.3V Voltage level
ADBUS0TCKJP2-8,
TCK_0 (FPGA PL BANK 0)
Clock Signal Output3.3V Voltage level.
MPSSE Mode
ADBUS1TDIJP2-11,
TDI_0 (FPGA PL BANK 0)
Serial Data Output3.3V Voltage level.
MPSSE Mode
ADBUS2TDOJP2-10,
TDO_0 (FPGA PL BANK 0)
Serial Data Input3.3V Voltage level.
MPSSE Mode
ADBUS3TMSJP2-7,
TMS_0 (FPGA PL BANK 0)
Output Signal Select3.3V Voltage level.
MPSSE Mode
BDBUS0UART_TX_OBU36-5Asynchronous serial TXDU36-3 Bus Switch pin connects later this signal to UART_RX_ZYNQ when UART_OB_DISABLE is low or floating.
BDBUS1UART_RX_OBU36-6Asynchronous serial RXDU36-2 Bus Switch pin connects later this signal to UART_TX_ZYNQ when UART_OB_DISABLE is low or floating.
OSCIOSCI
Oscillator input-
EECS, EECLK, EEDATAEECS, EECLK, EEDATAU40-1..3EEPROM interface-
-UART_OB_DISABLEJP1-11Enable signal of the FTDI-PS_UART Bus Switch U36.Active Low!.


...

Power supply with minimum current capability of 3.0 A (TBD*) for system startup is recommended.

* TBD - To Be Determined

Power Consumption

Scroll Title
anchorTable_PWR_PC
titlePower Consumption

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Power Input PinTypical Current
+5.0VTBD*
+5.0V_VAAless than 250mA (TBD*)


* TBD - To Be Determined

...

Scroll Title
anchorFigure_PWR_PD
titlePower Distribution


Scroll Ignore

draw.io Diagram
borderfalse
diagramNamePWR-PD-TE0716-01
simpleViewerfalse
width
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth643
revision2


Scroll Only

Image Modified


Power-On Sequence

The TE0716 has only one common "PGOOD" signal (from U37, U43, U45 and U46), and there is no Enable for the board. You could control the startup of the board IC, by controlling the +5.0V and the +5.0V_VAA input signals only.

Scroll Title
anchorFigure_PWR_PS
titlePower Sequency


Scroll Ignore

draw.io Diagram
bordertrue
diagramNamePWR-PS-TE0716-01
simpleViewerfalse
width
linksauto
tbstyletop
lboxtrue
diagramWidth641
revision34


Scroll Only

Image Modified


Voltage Monitor Circuit

The TE0716 has also a Voltage Monitor IC. It keeps nRST signal low if the FPGA core voltage (+1.0V) drops under 0.84V or the 3.3V power supply drops to 2.94V or less.

Power Good signal is unique and comes from the power supplies IC U37, U43, U45 and U46, as you can see in the previous section "Power-On Sequence", and also could make nRST to remain low until PGOOD is high.

See also "Reset process." section in "Configuration Signals" for additional information.

Scroll Title
anchorFigure_PWR_VMC
titleVoltage Monitor Circuit


Scroll Ignore

draw.io Diagram
borderfalse
diagramNamePWR-PM-TE0716-01
simpleViewerfalse
width
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth641
revision3


Scroll Only

Image Added

Scroll Title
anchorFigure_PWR_VMC
titleVoltage Monitor Circuit
Scroll Ignore

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Scroll Only

image link to the generate DrawIO PNG file of this page. This is a workaround until scroll pdf export bug is fixed


Power Rails

Scroll Title
anchorTable_PWR_PR
titleModule power rails.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue


Power Rail Name

B2B Connector

JP1 Pin

B2B Connector

JP2 Pin

DirectionNotes
+5.0V1, 23, 351, 23, 35InputMain Supply voltage from the carrier board
+5.0V_VAA43, 44-InputAnalog Supply voltage from the carrier board
+3.3V (VREF_JTAG)-5OutputJTAG reference voltage.


...

Page properties
hiddentrue
idComments
  • This section is optional and only for modules.
  • use "include page" macro and link to the general B2B connector page of the module series,

    For example: 6 x 6 SoM LSHM B2B Connectors

    Include Page
    PD:6 x 6 SoM LSHM B2B ConnectorsPD:
    6 x 6 SoM LSHM B2B Connectors

...

Scroll Title
anchorTable_TS_AMR
titlePS absolute Absolute maximum ratings

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

SymbolsDescriptionMinMaxUnitReference
+5.0VMain Supply voltage from the carrier board-0.36.0VNCV6357 Datasheet
NCV6323 Datasheet
NCP160 Datasheet
+5.0V_VAAAnalog Supply voltage from the carrier board-0.36.0VNCP160 Datasheet
MIO 500I/O input voltage for MIO bank 500-0.43.85VXilinx DS187 Datasheet
MIO 501I/O input voltage for MIO bank 501-0.42.35VXilinx DS187 Datasheet
PL HRI/O input voltage for HR banks-0.43.85VXilinx DS187 Datasheet
ADCx_P/NI/O input voltage for ADCs analog inputs-0.33.63VNCD98011 Datasheet


...

Scroll Title
anchorTable_TS_ROC
titleRecommended operating conditions.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

ParameterMinMaxUnitsReference Document
+5.0V Main Supply input voltage
from the carrier board
4.05.5V

7WB3125 Datasheet

NCV6357 Datasheet

NCV6323 Datasheet

NCP160 Datasheet

+5.0V_VAA Analog Supply input voltage
from the carrier board
3.755.5VNCP160 Datasheet
I/O input voltage for MIO bank 500-0.23.x5VXilinx DS187 Datasheet
I/O input voltage for MIO bank 501-0.22.x0VXilinx DS187 Datasheet
I/O input voltage for HR banks-0.23.x5VXilinx DS187 Datasheet
I/O input voltage for ADCs analog inputs-0.23.x4VNCD98011 Datasheet


Physical Dimensions

...

Page properties
hiddentrue
idComments

Set correct link to the shop page overview table of the product on English and German.

Example for TE0706:

    ENG Page: https://shop.trenz-electronic.de/en/search?sSearch=TE0706TE0716

    DEU Page: https://shop.trenz-electronic.de/de/search?sSearch=TE0706TE0716


Scroll Title
anchorTable_VCP_SO
titleTrenz Electronic Shop Overview

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Trenz shop TEXXXX TE0716 overview page
English pageGerman page


...

Scroll Title
anchorFigure_RV_HRN
titleBoard hardware revision number.


Scroll Ignore

draw.io Diagram
borderfalse
diagramNameRH-HRN-TE0716-01
simpleViewerfalse
width
linksauto
tbstylehidden
diagramDisplayName
lboxtrue
diagramWidth545
revision4


Scroll Only

Image Added

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Scroll Only

image link to the generate DrawIO PNG file of this page. This is a workaround until scroll pdf export bug is fixed


Document Change History

Page properties
hiddentrue
idComments
  • Note this list must be only updated, if the document is online on public doc!
  • It's semi automatically, so do following
    • Add new row below first

    • Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> this point is will be deleted on newer pdf export template

    • Metadata is only used of compatibility of older exports

...

Scroll Title
anchorTable_RH_DCH
titleDocument change history.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DateRevisionContributorDescription

Page info
infoTypeModified date
dateFormatyyyy-MM-dd
typeFlat

Page info
infoTypeCurrent version
prefixv.
typeFlat
showVersionsfalse

Page info
infoTypeModified by
typeFlat
showVersionsfalse

change list

  • Correction power rail

2020-10-30v.85Guillermo Herrera
  • initial release

--

all

Page info
infoTypeModified users
typeFlat
showVersionsfalse

  • --


...