Page History

...

• SoC/FPGA
  
  • Package: CLG484
  • Device: Xilinx Z-7020
  • Speed: -1 *
  • Temperature: C grade *.
• RAM/Storage
  • Low Power DDR3 SDRAM on PS
    • Data width: 32bit
    • Size: def. 1GB *
    • Speed: 1600 Mbps **
  • QSPI boot Flash
    • Data width: 4bit
    • size: 32MB *
  • MAC address serial EEPROM with EUI-48™ node identity (Microchip 24AA025E48).
  • 512Kb user MAC address serial EEPROM.
• On Board
  
  • 10x 12-Bit Low Power SAR ADCs up to 2 MSPS (NCD98011).
  • Low Power Oscillators.
  • Gigabit Ethernet PHY transceiver (Marvell Alaska 88E1512).
  • Hi-speed USB2 ULPI transceiver with full OTG support (Microchip USB3320C).
  • Single chip High Speed USB 2.0 to UART/JTAG Interface (Xilinx License included) (FTDI FT2232H).
  • 2xUser RGB LEDs (Green), LED FPGA DONE (Green).
  • 2 x Tactile Switches (User), 1 x Tactile Switche (Reset).
• Interface
  • 120 x HR PL I/Os (3 banks).
  • 2x PS MIOs (shared with UART TX/RX ZYNQ-FTDI).
  • 1 Gbps RGMII Ethernet interface.
  • High Speed USB2 ULPI with full OTG support.
  • High Speed USB 2.0 to UART/JTAG Interface, including microUSB-B connector.
  • Card Connector microSD™.
  • JTAG.

• Power
  
  • On-board high-efficiency DC-DC converters for all voltages used.
• Dimension
  • 65 x 45 mm
• Notes
  • * depends on assembly version
  • ** depends on used Zynq and DDR3 combination

...

1. Xilinx Zynq XC7Z SoC, U5 (Top)
2. 4Gbit DDR3/L SDRAM, U13 (Top)
3. 4Gbit DDR3/L SDRAM, U12 (Top)
4. 32MByte Quad SPI Flash memory, U7 (Top)
5. 2Kbit MAC address serial EEPROM with EUI-48TM node identity, U24 (Top)
6. 512Kb Serial EEPROM memory, U21 (Top)
7. 10x 12-Bit Low Power SAR ADCs, U1..U4, U10, U11, U15..U17, U19 (Top)
8. High-speed USB 2.0 ULPI transceiver, U18 (Top)
9. Single chip USB Interface 2.0 to UART / JTAG, U39 (Top)
10. MicroUSB-B connector, J13 (Top)
11. Low-power oscillator @ 12.000000MHz (OSCI-FTDI), U41 (Top)
12. Low-power oscillator @ 25.000000MHz (ETH-CLK), U9 (Top)
13. LED FPGA DONE (Green) 13 d3 (Top)
14. User RGB LED 1 D4 (Top)
15. User RGB LED 2 D5 (Top)
16. Tactile Switch (User), S1 (Top)
17. Tactile Switch (User), S2 (Top)
18. Tactile Switch (Reset), S3 (Top)
19. 5A Synchronous Buck DC-DC Converter (1V), U37 (Top)
20. 2A Synchronous Buck DC-DC Converter (3.3V), U46 (Top)
21. 2A Synchronous Buck DC-DC Converter (1.8V), U45 (Top)
22. 2A Synchronous Buck DC-DC Converter (1.5V), U43 (Top)
23. 250mA Ultra-Low Noise LDO Regulator (3.3V_ADC Digital I/O supply), U23 (Top)
24. 250mA Ultra-Low Noise LDO Regulator (ADC_VAA Analog supply/reference, 3.3V), U38 (Top)
25. Gigabit Ethernet PHY transceiver, U8 (Bottom)
26. Low-power oscillator @ 33.333333MHz (PS-CLK), U6 (Bottom)
27. 3A Sink/Source DDR Termination Regulator (VTT/VTTREF, 0.75V), U47 (Bottom)
28. Card Connector microSD™, J2 (Bottom)
29. 2x60 positions high speed/density plug connector, JP1 (Bottom)
30. 2x60 positions high speed/density plug connector, JP2 (Bottom)

Initial Delivery State

...