Page History
...
#1 Generic options: PUDC and Boot Mode
Type: Enhancement
Reason: Adjustable pullup or pulldown status for IO pins and changing the boot mode or PUDC for custom request faster
Impact: No Impact, default CPLD source code is still PUDC low (Pullups activated) and Boot Mode QSPI/SD
#2 MIO7 Pullnone
Type: Enhancement Enhancement
Reason: HW Pulldown on carrier for Bank0 Voltage selection (3.3V)
Impact: No Impact
#3 Adding internal en_3v3_int
Type: Enhancement
Reason: To connect 3.3V to enable pin of the 3.3V regulator after the core
Impact: To achive power sequencing correctly
#4 JTAG C_* high impedance until 3.3VOUT can be high
Type: Enhancement
Reason: JTAG pins connected to Zynq are high impedance as long as there is no voltage in the core.
Impact: No Impact, improve Power sequencing
#5 Boot mode pins are GND or high impedance until en_3v3_int are high
Type: Enhancement
Reason: Boot Mode pins connected to Zynq are high impedance as long as there is no voltage in the core.
Impact: No Impact, improve Power sequencing
#6 MIO14,15 high impedance until en_3v3_int are high
Type: Enhancement
Reason: UART pins that to Zynq connected are high impedance as long as there is no voltage in the core.
Impact: No Impact, improve Power sequencing
#7 JTAG time constraint
...
Type: Enhancement
Reason: Signal propagtion constraints to improve JTAG on high traffic
Impact: No Impact, improve JTAG connection
#8 JTAG drive line adjustment
Type: Enhancement
Reason: Driver constraints to improve JTAG on high traffic
Impact: No Impact, improve JTAG connection
#9 Bugfix I2C to GPIO module (I2C_to_GPIO.v)
Type: Enhancement Bugfix
Reason: To communicate corectly with I2C to GPIO subsystem
Impact:
...
Reading and writing data from/to CPLD internal registers via I2C bus correctly
#10 Changed Firmware Identifier to REV06
Type: Enhancement
Reason: show new firmware revision with Trenz FSBL
Impact: No Impact
More information about System Controller can be found here: TE0720 System Controller
...
All TE0720-03 SoMs noted in the column replacement are with REV06 CPLD firmware.
Precursor | Replacement |
---|---|
CPLD Firmware REV05 | CPLD Firmware REV06 |
TE0720-03-14S-1C | TE0720-03-31C33FA |
TE0720-03-1CFA | TE0720-03-61C33FA |
TE0720-03-1QF | TE0720-03-61Q33FA |
TE0720-03-1QFA | TE0720-03-61Q33FA |
TE0720-03-1QFA-V1 | TE0720-03-61Q33FAD |
TE0720-03-1QC11 | TE0720-03-61Q33FAE |
TE0720-03-1QC12 | TE0720-03-61Q33FAF |
TE0720-03-1QFL | TE0720-03-61Q33FL |
TE0720-03-2IF | TE0720-03-62I33FA |
TE0720-03-2IFA | TE0720-03-62I33FA |
TE0720-03-2IFC1 | TE0720-03-62I33FAN |
TE0720-03-2IFC3 | TE0720-03-62I33FL |
TE0720-03-62I12GA | TE0720-03-62I33GA |
TE0720-03-L1IF | TE0720-03-64I63FA |
TE0720-03-62I320M | TE0720-03-62I330M |
TE0720-03-1CR | TE0720-03-61C530A |
TE0720-03-1QFD | TE0720-03-61Q43FA |
TE0720-03-61Q42GA | TE0720-03-61Q43GA |
TE0720-03-1CFA-S | TE0720-03-61C33FAS |
Production Shipment Schedule
...