Page History

Table of content

Legend

• : Attention: Carrier/Module combination only with special condition or PCB modification possible
• : Supported
• : Supported with limitations
• : Not Supported
• : Table currently not complete, see TRM of module and carrier

TE0701

TE0701

 FMC

	FMC Vadj	PMODS	ETH	HDMI

Camera Link

CL Connector(5)	SD Card	USB Host	VBATT
TE0710

      

, N.C.

, N.C.

, 3.3V

1.8V

B16 I/O

Nonenot used

TE0711

        

,1.8V B16 I/O

, device only(14)

 

TE0712

   

,100 MBit*

 

,MGT's

   TE0713         TE0715     MGT'sfull supportfull support TE0720full supportfull supportfull supportfull supportfull supportfull supportfull supportfull supportused for RTC and Key RAMTE0741     MGT'sNot supported  TE0841     MGT'sNot supported  

TE0703

,1.8V B13 I/O
TE0713						,MGT's	,1.8V B13 I/O	, device only(14)
TE0715-15						,MGT's			, RTC and Key RAM
TE0715-30 (2)		,Max 1.8V				,MGT's			, RTC and Key RAM
TE0720						,LVDS			, RTC and Key RAM
TE0741 (4)						,MGT's	,MGT's
TE0820 (2)		,Max 1.8V				,MGT's	(6)		, PSBATT(7)
TE0821 (2)		,(Max 1.8V)				,MGT's	(6)		, PSBATT(7)
TE0823 (2)		,Max 1.8V				,MGT's	(6)		, PSBATT(7)
TE0841 (2)(3)						,MGT's	,MGT's		, Key RAM

• (1) FMC is a LPC Connector (no gigabit transceivers) on TE0701: I2C and JTAG access over CPLD.
       Separate TE0701_FMC_PINOUT table (PDF/XLSX) is available on: Trenz_Electronic Download-Pinout
• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
• (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
• (5) CL Connector is usable as Cameralink only with module that map LVDS pins to this connector
• (6) Works, but without carrier board modification out of specification: TE0701 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
• (7) PS battery operated voltage (1.2V–1.5V).
• (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage

TE0703

...

	ETH	SD Card	USB Host	Reset	User LEDs	USB UART	USB JTAG
TE0710

 

		, 3.3V B16 I/O			, 2 LEDs
TE0711		, 1.8V B16 I/O

NoneTE0711   None

, device only(14)
TE0712	, 100 MBit

  NoneTE0713   NoneTE0715  full supportTE0720full supportfull supportfull supportTE0741   NoneTE0841   None

TE0705

, 1.8V B13 I/O
TE0713		, 1.8V B13 I/O	, device only(14)
TE0715-15
TE0715-30 (2)
TE0720
TE0741 (4)		, MGTs
TE0820 (2)		(6)
TE0821 (2)		(6)
TE0823 (2)		(6)
TE0841 (2)(3)		, MGTs
TEG2000		, 1.8V Bank SB I/O			, 1 LED

• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
• (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
• (6) REV06 select correct SDIO voltage by jumper J11. REV05 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).
• (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage

TE0705

 

PMODS	ETH	SD Card	USB Host
TE0710

  1

, 3.

8V

3V B16 I/O

None

TE0711

    None

	,1.8V B16 I/O	, device only(14)
TE0712

 

100 MBit

  NoneTE0713    NoneTE0715  full support full supportTE0720full supportfull supportfull supportfull supportTE0741    NoneTE0841    None

TE0706

,1.8V B13 I/O
TE0713				, device only(14)
TE0715-15
TE0715-30 (2)
TE0720
TE0741 (4)			,MGT's
TE0820 (2)			(6)
TE0821 (2)			(6)
TE0823 (2)			(6)
TE0841 (2)(3)			,MGT's

• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
• (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
• (6) Works, but without carrier board modification out of specification: TE0705 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
• (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage

TE0706

...

	ETH1	ETH2	SD Card	USB Host
TE0710			, 3.3V B16 I/O
TE0711			, 1.8V B16 I/O	, device only(14)
TE0712	100 MBit		, 1.8V B13 I/O
TE0713				, device only(14)
TE0715-15
TE0715-30 (2)
TE0720
TE0741 (4)			, MGTs
TE0820 (2)			(6)
TE0821 (2)			(6)
TE0823 (2)			(6)
TE0841 (2)(3)			, MGTs

• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
• (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
• (6) REV03 select correct SDIO voltage by jumper. REV02 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).
• (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage

TEB0707

	ETH	SD Card	USB Host	HS CA(15)	HS CB(15)	HS CC(15)	LS CA(16)	User LEDs(17)	USB UART	USB JTAG
TE0710		, 3.3V B16 I/O

NoneTE0711    TE0712100 MBit   TE0713    TE0715 full supportfull support full supportTE0720full supportfull supportfull supportfull supportTE0741    TE0841    

TE0711		, 1.8V B16 I/O
TE0712	100 MBit	, 1.8V B13 I/O			, some fix 3.3V B14 I/O
TE0713					(19)
TE0715-15								(3x PL, 3x PS)
TE0715-30 (2)				, max  1.8V	, max  1.8V			(3x PL, 3x PS)
TE0720								(3x PL, 3x PS)
TE0741 (4)		, MGTs		(18)
TE0820 (2)		(6)		, max  1.8V	, max  1.8V	, max  1.8V		(3x PL, 3x PS)
TE0821 (2)		(6)			, max  1.8V			(3x PL, 3x PS)
TE0823 (2)		(6)		, max  1.8V	, max  1.8V	, max  1.8V		(3x PL, 3x PS)
TE0841 (2)(3)		, MGTs			, max  1.8V	, max  1.8V		(3x PL, 3x PS)

• (2) HP IO Banks only support 1.8V
• (3) MGT's Lanes connected to SD-Level shifter: TEB0707 - Leave J4 open.
• (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
• (6) Select correct SDIO voltage by jumper.
• (15) Fix 3.3V signals of CRUVI HS connectors are connected to MAX10 CPLD and can be used firmware dependent (In standard firmware not implemented).
• (16) Signals on CRUVI LS connector are connected to MAX10 CPLD and can be used firmware dependent (In standard firmware 4 input and 4 output).
• (17) LEDs are connected to MAX10 CPLD and can be used firmware dependent (In standard Firmware implemented.)
• (18) Not available on assembly variants with K70T.
• (19) Two diff. pairs connected to FT600 USB3 lanes. Other signals usable.

TEBA0841

	SFP	USB Host	SD Card "J4 2x5 Pin Header(2.54)"	GPIO "J20/J10 each 2x25 Pin Header(2.54)"	XMOD (JTAG/UART) "JX1 2x6 Pin Header (2.54)"	GPIO (JTAG/UART/MGT REFCLK) "J3 2x8 Pin Header(2.54)"
TE0710			,3.3V B16 I/O	(9)		(8)
TE0711		, device only(14)	,1.8V B16 I/O	(9)		, B34 CLK input
TE0712			,  B13 I/O	(9)		, B34 CLK input
TE0713		, device only(14)	,  B13 I/O	(9)
TE0715 (10)			(7)	(9)
TE0715-30 (10)			(7)	(9)
TE0720 (10)			(7)	(9)		, B34 CLK input
TE0741 (11)			,MGT's	(9)
TE0820 (10)			(6)	(9)
TE0821 (10)			(6)	(9)
TE0823 (10)			(6)	(9)
TE0841			,MGT's	(9)

• TEBA0841 has no dedicated power plug connector for 3.3V main power. External Power Supply must be connected to  J17, J20, J4 or J3 3.3V Pin. Do not use XMOD for power supply.
• TEBA0841-REV01 VCCIOB and VCCIOC are not connected.
• (6) Works, but without carrier board modification out of specification: TE0706 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
• (7) SD signals only, no SD-Card connector
• (8) CLK not connected on TE0710
• (9) Check schematics  or TE Master Pinout Excel Sheet for detailed connection and IO Bank power supply
• (10) With TEBA0841-01 is Boot Mode not selectable, please contact Trenz Electronic Support, if you need a Zynq or ZynqMP Module with TEBA0841-1. With TEBA0841-2 it's usable.
• (11) MGT polarity is swapped

TEF1002

	FMC	FMC Vadj	SFP	SATA	PCIe	USB Host	SD Card	Ethernet	FFA & FFB	USB UART	USB JTAG
TE0710	, no MGT, 19x diff pair / 38x IO						, 3.3V B16 I/O
TE0711	, VCCIO34 B34 I/O on MGT					, device only(14)	, 1.8V B16 I/O	, B34 I/Os
TE0712						, B14 3.3V I/Os	, 1.8V B13 I/O
TE0713						, device only(14)	, 1.8V B13 I/O	, B13 I/Os
TE0715
TE0715-30		, Max 1.8V
TE0720  (12)	, VCCIO34 B34 I/O on MGT
TE0741						, B14 3.3V I/Os	, MGTs	, MGTs
TE0820 (13)		, Max 1.8V
TE0821 (13)		, Max 1.8V
TE0823 (13)		, Max 1.8V
TE0841		, Max 1.8V				, B65 3.3V I/Os	, MGTs	, MGTs

• (12) FMC_VADJ powers VCCIOC connected to power input of Bank 34 VCCO34 on TE0720 needed to start up. In standard Firmware dip S3-2 can be used to switch ON FMC_VADJ without FMC installed. 
• (13) FMC_VADJ powers VCCIOC connected to power input of Bank 65 VCCO_65 and VDDO0 of CLK0 on TE0820. In standard Firmware dip S3-2 can be used to switch ON FMC_VADJ without FMC installed. Select VADJ_FMC 1.8V (HP bank)!
• (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage

TEB2000

	ETH	SD Card	USB Host	Reset	User LEDs	USB UART	Debug UART	USB JTAG
TEM0007

3rd Party Carrier