Page History
...
- (1) FMC is a LPC Connector (no gigabit transceivers) on TE0701: I2C and JTAG access over CPLD.
Separate TE0701_FMC_PINOUT table (PDF/XLSX) is available on: Trenz_Electronic Download-Pinout - (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
- (5) CL Connector is usable as Cameralink only with module that map LVDS pins to this connector
- (6) Works, but without carrier board modification out of specification: TE0701 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
- (7) PS battery operated voltage (1.2V–1.5V).
- (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage
TE0703
| ETH | SD Card | USB Host | Reset | User LEDs | USB UART | USB JTAG | |
|---|---|---|---|---|---|---|---|
| TE0710 |  |  , 3.3V B16 I/O |  |  | , 2 LEDs | | |
| TE0711 | | , 1.8V B16 I/O | , device only(14) | | | | |
| TE0712 | , 100 MBit | , 1.8V B13 I/O | | | | | |
| TE0713 | | , 1.8V B13 I/O | , device only(14) | | | | |
| TE0715-15 | | | | | | | |
TE0715-30  (2) | | | | | | | |
| TE0720 | | | | | | | |
| TE0741 (4) | | , MGTs | | | | | |
| TE0820 (2) | | (6) | | | | | |
| TE0821 (2) | | (6) | | | | | |
| TE0823 (2) | | (6) | | | | | |
| TE0841 (2)(3) | | , MGTs | | | | | |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
- (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
- (6) REV06 select correct SDIO voltage by jumper J11. REV05 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).
- (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage
TE0705
| PMODS | ETH | SD Card | USB Host | |
|---|---|---|---|---|
| TE0710 | | | , 3.3V B16 I/O | |
| TE0711 | | | ,1.8V B16 I/O | , device only(14) |
| TE0712 | | 100 MBit | ,1.8V B13 I/O | |
| TE0713 | | | | , device only(14) |
| TE0715-15 | | | | |
| TE0715-30 (2) | | | | |
| TE0720 | | | | |
| TE0741 (4) | | | ,MGT's | |
| TE0820 (2) | | | (6) | |
| TE0821 (2) | | | (6) | |
| TE0823 (2) | | | (6) | |
| TE0841 (2)(3) | | | ,MGT's | |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
- (6) Works, but without carrier board modification out of specification: TE0705 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
- (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage
TE0706
| ETH1 | ETH2 | SD Card | USB Host | |
|---|---|---|---|---|
| TE0710 | | | , 3.3V B16 I/O | |
| TE0711 | | | , 1.8V B16 I/O | , device only(14) |
| TE0712 | 100 MBit | | , 1.8V B13 I/O | |
| TE0713 | | | | , device only(14) |
| TE0715-15 | | | | |
| TE0715-30 (2) | | | | |
| TE0720 | | | | |
| TE0741 (4) | | | , MGTs | |
| TE0820 (2) | | | (6) | |
| TE0821 (2) | | | (6) | |
| TE0823 (2) | | | (6) | |
| TE0841 (2)(3) | | | , MGTs | |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes connected to SD-Level shifter: TE0703-06: Leave J11 open; TE0703-05 and before: It's recommended to desolder level shifter.
- (4) MGT's Lanes connected to SD-Level shifter, but module side 1.8V is not connected.
- (6) REV03 select correct SDIO voltage by jumper. REV02 and before: Works, but without carrier board modification out of specification (TE0703 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V).
- (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage
TEBA0841
| SFP | USB Host | SD Card "J4 2x5 Pin Header(2.54)" | GPIO | XMOD (JTAG/UART) "JX1 2x6 Pin Header (2.54)" | GPIO (JTAG/UART/MGT REFCLK) "J3 2x8 Pin Header(2.54)" | |
|---|---|---|---|---|---|---|
| TE0710 | | | ,3.3V B16 I/O | (9) | | (8) |
| TE0711 | | , device only(14) | ,1.8V B16 I/O | (9) | | , B34 CLK input |
| TE0712 | | | , B13 I/O | (9) | | , B34 CLK input |
| TE0713 | | , device only(14) | , B13 I/O | (9) | | |
| TE0715 (10) | | | (7) | (9) | | |
| TE0715-30 (10) | | | (7) | (9) | | |
TE0720 | | | (7) | (9) | | , B34 CLK input |
TE0741 (11) | | | ,MGT's | (9) | | |
| TE0820 (10) | | | (6) | (9) | | |
| TE0821 (10) | | | (6) | (9) | | |
| TE0823 (10) | | | (6) | (9) | | |
| TE0841 | | | ,MGT's | (9) | | |
- TEBA0841 has no dedicated power plug connector for 3.3V main power. External Power Supply must be connected to J17, J20, J4 or J3 3.3V Pin. Do not use XMOD for power supply.
- TEBA0841-REV01 VCCIOB and VCCIOC are not connected.
- (6) Works, but without carrier board modification out of specification: TE0706 SD Levelshifter powered fix by 1.8V, TE0820 SD MIO-Bank by 3.3V.
- (7) SD signals only, no SD-Card connector
- (8) CLK not connected on TE0710
- (9) Check schematics or TE Master Pinout Excel Sheet for detailed connection and IO Bank power supply
- (10) With TEBA0841-01 is Boot Mode not selectable, please contact Trenz Electronic Support, if you need a Zynq or ZynqMP Module with TEBA0841-1. With TEBA0841-2 it's usable.
- (11) MGT polarity is swapped
- (14) via FTDI FIFO bridge, VBUS Network is for host
TEF1002
| FMC | FMC Vadj | SFP | SATA | PCIe | USB Host | SD Card | Ethernet | FFA & FFB | USB UART | USB JTAG | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TE0710 | , no MGT, 19x diff pair / 38x IO | | | | | | , 3.3V B16 I/O | | | | |
| TE0711 | , VCCIO34 B34 I/O on MGT | | | | | , device only(14) | , 1.8V B16 I/O | , B34 I/Os | | | |
| TE0712 | | | | | | , B14 3.3V I/Os | , 1.8V B13 I/O | | | | |
| TE0713 | | | | | | , device only(14) | , 1.8V B13 I/O | , B13 I/Os | | | |
| TE0715 | | | | | | | | | | | |
| TE0715-30 | | , Max 1.8V | | | | | | | | | |
TE0720 (12) | , VCCIO34 B34 I/O on MGT | | | | | | | | | | |
| | | | | , B14 3.3V I/Os | , MGTs | , MGTs | | | | |
| TE0820 (13) | | , Max 1.8V | | | | | | | | | |
| TE0821 (13) | | , Max 1.8V | | | | | | | | | |
| TE0823 (13) | | , Max 1.8V | | | | | | | | | |
| TE0841 | | , Max 1.8V | | | | , B65 3.3V I/Os | , MGTs | , MGTs | | | |
- (12) FMC_VADJ powers VCCIOC connected to power input of Bank 34 VCCO34 on TE0720 needed to start up. In standard Firmware dip S3-2 can be used to switch ON FMC_VADJ without FMC installed.
- (13) FMC_VADJ powers VCCIOC connected to power input of Bank 65 VCCO_65 and VDDO0 of CLK0 on TE0820. In standard Firmware dip S3-2 can be used to switch ON FMC_VADJ without FMC installed. Select VADJ_FMC 1.8V (HP bank)!
- (14) via FTDI FIFO bridge, VBUS Network is default assembled for host usage
3rd Party Carrier
| Name | Manufacturer | Product Link | Trenz Shop |
|---|---|---|---|
| EMC2-DP | Sundance | PC/104 OneBank Carrier for SoC Modules | EMC2-DP |
oi110 | Sundance | oi110 – Dual CameraLink | --- |
oi111 | Sundance | oi111 – Dual SDI + Analog Video | --- |
oi115 | Sundance | oi115 – HDMI In / Out | --- |
...
Overview
Content Tools