Page History

...

• TE0808 - UltraSoM+ - Wiki with TRM, reference projects, application notes and more
  • TE0808 Resources - Links to all TE0808 Resources
• TEBF0808 - Wiki with TRM, application notes and more
  • TEBF0808 Resources - Links to all TEBF0808 Resources
• TE0790 - XMOD - Wiki with TRM, application notes and more
  • TE0790 Resources - Links to all TE0790 Resources
• Vivado/SDK/SDSoC AMD Development Tools - Short instructions for Vivado, SDK, SDSoC
• Project Delivery - AMD devices - General descriptions of reference designs and content

...

Shop Links

• Shop TE0808-Starter-Kit - contains prices, order number, content... contains prices, available stock, disposability, scope of delivery and more

Xilinx Software and Driver

• Vivado Design Suite - Xilinx Design Software with JTAG drivers and documentation
• Xilinx Download Area - All Xilinx Software, Device Models and Libraries
  
  

Additional Documentation

Important Notes

...

Getting Started

Starter Kit is shipped with prebuilt Linux Example on SD. Newest version and sources are available on our download area: TE0808 Reference Designs

1. Connect main power and set power switch to on. See Main Power Enclosure Location

2. Connect mini USB cable from XMOD with green dot to host PC. See XMODs Connection
3. Insert SD-Card with pre-loaded content into SD-Card slot.
4. Open Serial Console:
   1. COM Port: for correct number see device manager
   2. Speed:115200
5. Press the Power on button on the enclosure. See Power Button, Reset Button, HDD LED and Power LED Enclosure Location
6. Linux login:
   
   1. User Name:root
   2. Password:root

• TEBF0808 Getting Started - Basic note to start up Carrier with TE080x modules

Starter Kit Basic

Main Power Enclosure Location

Power Button , Reset Button, HDD LED and Power LED Enclosure  Location

Default DIP Switch Settings

...

For more information, see:TEBF0808, TEBF0808 Master CPLD and TEBF0808 Slave CPLD.

Starter Kit Status

- Section is currently not complete -

Main Power Switch is OFF

No Power on Starter Kit.

Identification: FANs do not work, all LEDs are off.

Main Power Switch is ON and Power Button is not pressed

Only some basics on TEBF0808 are powered on. This mode is used for CPLDs Firmware updates.

Identification: FANs do not work, some LEDs blinking.

LED description(need CPLD Firmware REV06 or newer):

...

Indicate board is powered off.

...

RGPIO 14 and 15, if RGPIO is active.

...

MIO40, if RGPIO is deactivated

Main Power Switch is ON and Power Button is pressed first time

TE0808 will be powered on. System boots if boot mode is set correct and files are available.

Identification: FANs do work, LEDs blinking states change.

LED description (need CPLD Firmware REV06 or newer):

...

Indicate board is powered off.

...

RGPIO 14 and 15, if RGPIO is active.

...

MIO40, if RGPIO is deactivated

...

Indicates the PS is not initialized after a power-on reset (POR).

...

The PS_ERROR_OUT signal is asserted for accidental loss of power, an error, or an exception in the PMU.

...

The PS_ERROR_STATUS indicates a secure lockdown state. Alternatively, it can be used by the PMU firmware to indicate system status.

...

RGPIO 16 and 17, if RGPIO is active

...

SI5345 NVM Programming

SI5345 NVM on the module is not programmed on factory, so modified FSBL is needed to get running output CLKS.

It is possible to program NVM of the SI5345 2 times, see Si5345

Notes

Most LEDs are CPLD Firmware dependents, see TEBF0808 Master CPLD and TEBF0808 Slave CPLD

Starter Kit Cable Connection

Starter Kit will be shipped with all cable connected.

ATX Power

Module

FMC FAN

XMODs

Enclosure USB

Enclosure FAN1 and HDAUDIO

Enclosure Power Button , Reset Button, HDD LED and Power LED

Support

• For support, please go to http://forum.trenz-electronic.de/ or contact support@trenz-electronic.de