Page History
This Trenz Electronic Starter Kit Kit consists of a TE0803 module on a TEBF0808 base board in Mini-ITX Enclosure. See Shop Link shop link for detailed content.
Wiki Links
...
...
- - Wiki with TRM, reference projects, application notes and more
- TE0803 Resources - Links to all TE0803 resources
- TEBF0808 - Wiki with TRM, application notes and more
- TEBF0808 Resources - Links to all TEBF0808 resources
- TE0790 - XMOD
...
- - Wiki with
...
- TRM, application notes and more
- TE0790 Resources - Links to all TE0790 resources
- AMD Development Tools - Short instructions for Vivado, SDK, SDSoC
- Project Delivery - AMD devices - General descriptions of reference designs and content
Download Links
- TE0803 Download Area - contains various reference designs, schematics, hardware designs, 3D models and more
- TEBF0808 Download Area - contains schematics, hardware designs, 3D models and more
- TE0790-XMOD Download Area - contains firmware with projects, schematics, hardware designs, 3D models and more
- TE Master Pinout - Excel
...
- sheet as pinout viewer and XDC
...
- generator
Shop Links
...
- contains prices, available stock, disposability, scope of delivery and more
Xilinx Software and Driver
- Vivado Design Suite - Xilinx Design Software with JTAG drivers and documentation. Vivado Webpack XCZU3CG/EG support will be available from Version 2017.1 .
- Xilinx Download Area - All Xilinx
...
- software,
...
- device models and
...
- libraries
Important Notes
Warning |
---|
Do not change XMOD DIP-Switch settings on TEBF0808. Do not swap the XMOD adapters, the one marked with a green dot must be closer to the SoM |
...
Note |
---|
ES devices are not included in all Vivado versions, for ES1 only: activate beta device see: FAQ - How can I activate beta devices? |
Note |
---|
For all Starter Kit's Kits shipped before 2017-06-21: Enclosure Power power and HD LED was swapped on connector. See "Enclosure Power Button, Reset Button, HDD LEDand Power LED" section for correct connection. |
Getting Started
Starter Kit is shipped with prebuilt Linux Example on SD. Newest version and sources are available on our download area: TE0803 Reference Designs
...
Connect main power and set power switch to on. See Main Power Enclosure Location
...
- COM Port: for correct number see device manager
- Speed:115200
...
TEBF0808 Getting Started - Basic note to start up Carrier with TE080x modules
Starter Kit Basic
Main Power Enclosure Location
...
Power Button , Reset Button, HDD LED and Power LED Enclosure Location
Default DIP Switch Settings
Warning |
---|
Do not change XMOD DIP-Switch settings on TEBF0808. Do not swap the XMOD adapters, the one marked with a green dot must be closer to the SoM |
...
TEBF0808 | TE0790-02 (with green dot) | TE0790-02L | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
|
|
Note: with CPLD Firmware REV06 or newer, S4.4 can be set to OFF, to save power, if Starter Kit is powered off with Power Button.
For more information , see: TEBF0808
Status LEDs
- Section is currently not complete -
...
SI5338 Programming
SI5338 NVM on the module is not programmed on factory, so modified FSBL is needed to get running output CLKS.
It is not possible to program NVM after device is soldered. More information to program SI5338 , see Si5338
Starter Kit Cable Connection
...
Enclosure Power Button , Reset Button, HDD LED and Power LED
Support
- For support, please go to http://forum.trenz-electronic.de/ or contact support@trenz-electronic.de