Page History
...
- TE0803 - UltraSoM+ - Wiki with TRM, reference projects, application notes and more
- TE0803 Resources - Links to all TE0803 Resourcesresources
- TEBF0808 - Wiki with TRM, application notes and more
- TEBF0808 Resources - Links to all TEBF0808 Resourcesresources
- TE0790 - XMOD - Wiki with TRM, application notes and more
- TE0790 Resources - Links to all TE0790 Resourcesresources
- AMD Development Tools Vivado/SDK/SDSoC - Short instructions for Vivado, SDK, SDSoC
- Project Delivery - AMD devices - General descriptions of reference designs and content
...
- TE0803 Download Area - contains various reference designs, schematics, hardware designs, 3D models and more
- TEBF0808 Download Area - contains schematics, hardware designs, 3D models and more
- TE0790-XMOD Download Area - contains firmware with projects, schematics, hardware designs, 3D models and more
- TE Master Pinout - Excel Sheet as Pinout-Viewer sheet as pinout viewer and XDC -Generatorgenerator
Shop Links
- Shop TE0803-Starter-Kit - contains prices, available stock, disposability, scope of delivery and more
...
- Vivado Design Suite - Xilinx Design Software with JTAG drivers and documentation. Vivado Webpack XCZU3CG/EG support will be available from Version 2017.1 .
- Xilinx Download Area - All Xilinx Softwaresoftware, Device Models device models and Librarieslibraries
Important Notes
Warning |
---|
Do not change XMOD DIP-Switch settings on TEBF0808. Do not swap the XMOD adapters, the one marked with a green dot must be closer to the SoM |
...
Note |
---|
ES devices are not included in all Vivado versions, for ES1 only: activate beta device see: FAQ - How can I activate beta devices? |
Note |
---|
For all Starter Kit's Kits shipped before 2017-06-21: Enclosure Power power and HD LED was swapped on connector. See "Enclosure Power Button, Reset Button, HDD LEDand Power LED" section for correct connection. |
Getting Started
Starter Kit is shipped with prebuilt Linux Example on SD. Newest version and sources are available on our download area: TE0803 Reference Designs
Connect main power and set power switch to on. See Main Power Enclosure Location
- Connect mini USB cable from XMOD with green dot to host PC. See XMODs Connection
- Insert SD-Card with pre-loaded content into SD-Card slot.
- Open Serial Console:
- COM Port: for correct number see device manager
- Speed:115200
- Press the Power on button on the enclosure. See Power Button, Reset Button, HDD LED and Power LED Enclosure Location
- Linux login:
- User Name:root
- Password:root
TEBF0808 Getting Started - Basic note to start up Carrier with TE080x modules
Starter Kit Basic
Main Power Enclosure Location
...
Warning |
---|
Do not change XMOD DIP-Switch settings on TEBF0808. Do not swap the XMOD adapters, the one marked with a green dot must be closer to the SoM |
...
Note: with CPLD Firmware REV06 or newer, S4.4 can be set to OFF, to save power, if Starter Kit is powered off with Power Button.
For more information , see:TEBF0808, TEBF0808 Master CPLD and TEBF0808 Slave CPLD.
Starter Kit Status
- Section is currently not complete -
Main Power Switch is OFF
No Power on Starter Kit.
Identification: FANs do not work, all LEDs are off.
Main Power Switch is ON and Power Button is not pressed
Only some basics on TEBF0808 are powered on. This mode is used for CPLDs Firmware updates.
Identification: FANs do not work, some LEDs blinking.
LED description (need CPLD Firmware REV06 or newer):
...
Indicate board is powered off.
...
RGPIO 14 and 15, if RGPIO is active.
...
MIO40, if RGPIO is deactivated
Main Power Switch is ON and Power Button is pressed first time
TE0803 will be powered on. System boots, if boot mode is set correct and files are available.
Identification: FANs do work, LEDs blinking states change.
LED description(need CPLD Firmware REV06 or newer):
...
Indicate board is powered off.
...
RGPIO 14 and 15, if RGPIO is active.
...
MIO40, if RGPIO is deactivated
...
Indicates the PS is not initialized after a power-on reset (POR).
...
The PS_ERROR_OUT signal is asserted for accidental loss of power, an error, or an exception in the PMU.
...
The PS_ERROR_STATUS indicates a secure lockdown state. Alternatively, it can be used by the PMU firmware to indicate system status.
...
RGPIO 16 and 17, if RGPIO is active
...
SI5338 Programming
SI5338 NVM on the module is not programmed on factory, so modified FSBL is needed to get running output CLKS.
It is not possible to program NVM after device is soldered. More information to program SI5338 , see Si5338
Notes
...
Starter Kit Cable Connection
...