Page History
Legend:
: Attention: Carrier/Module combination only with special condition or PCB modification possible
: Supported
: Supported with limitations
: Not Supported
: Table currently not complete, see TRM of Module and carrier
TE0701
| FMC(1) | FMC Vadj | PMODS | ETH | HDMI | CL Connector | SD Card | USB Host | VBATT | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TE0710 | Support | | | | no connection | | , N.C. | , 1.8V B16 I/O | Not supported | not used | |||||||||
| TE0711 | Support | | | | | | | Not supported | not used | ||||||||||
| TE0712 | Support | | | ,100 MBit* | | , MGT's | | Not supported | not used | ||||||||||
| TE0713 | Support | | | not supported | | | | Not supported | not used | ||||||||||
| TE0715-15 | Support | Full support | | Full support | | , MGT's | Full support | Full support | | , used for RTC and Key RAM | |||||||||
| TE0715-30 (2) | Support | ,Max 1.8V | | Full support | | , MGT's | Full support | Full support | | , used for RTC and Key RAM | |||||||||
| TE0720 | Support | Full supportFull support | | Full supportFull support | | , LVDS | Full support | Full support | | , RTC used for RTC and Key RAM | |||||||||
| TE0741 (4) | Support | | | | | , MGT's | Not supported | Not supported | not used | ||||||||||
| TE0841 | Support | MGT's | Not supported | Not supported | used for Key RAM | ||||||||||||||
| ,MGT's | | | |||||||||||||||||
| TE0820 (2) | | | | | | | | | | ||||||||||
| TE0841 (2)(3) | | | | | | , MGT's | ,MGT's | | , Key RAM |
- (1) FMC is a LPC Connector on TE0701: DP0_..., GBTCLK0_... and TRST_L Pins are not connected. GA0 and GA1 set to GND. I2C and JTAG access over CPLD.
Separate TE0701_FMC_PINOUT table (PDF/XLSX) is available on: Trenz_Electronic Download-Pinout - (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
TE0703
| ETH | SD Card | USB Host | Reset | User LEDs | USB UART | USB JTAG | |
|---|---|---|---|---|---|---|---|
| TE0710 |
| , 1.8V B16 I/O |
|
| 2 |
|
|
| TE0711 |
|
|
|
|
|
|
| |
| TE0712 | ,100 MBit |
|
|
|
|
|
|
| TE0713 |
| | | | | | | |
| TE0715-15 | | | | | | | |
| TE0715-30 (2) | | | | | | | |
| TE0720 | | | | | | | |
| TE0741 (4) | | ,MGT's | | | | | |
| TE0820 (2) | | | | | | | |
| TE0841 (2)(3) | | ,MGT's | | | | | |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
TE0705
| PMODS | ETH | SD Card | USB Host | |
|---|---|---|---|---|
| TE0710 |
|
| , 1.8V B16 I/O |
|
| TE0711 |
|
|
|
|
| TE0712 |
| 100 MBit |
|
|
| TE0713 |
| | | | |
| TE0715-15 | | | | |
| TE0715-30 (2) | | | | |
| TE0720 | | | | |
| TE0741 (4) | | | ,MGT's | |
| TE0820 (2) | | | | |
| TE0841 (2)(3) | ,MGT's | |
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
TE0706
| ETH1 | ETH2 | SD Card | USB Host | |
|---|---|---|---|---|
| TE0710 | | | , 1.8V B16 I/O | Not supported |
| TE0711 | | | | Not supported |
| TE0712 | 100 MBit | | | Not supported |
| TE0713 | Not supported | |||
| TE0715 | Full support | Full support | Full support | |
| TE0720 | Full support | Full support | Full support | Full support |
| TE0741 | Not supported | |||
| TE0841 | Not supported |
TEBA0841
...
- (2) HP IO Banks only support 1.8V
- (3) MGT's Lanes goes to SD-Level shifter, it's recommended to desoldering level shifter
- (4) MGT's Lanes goes to SD-Level shifter, but module side 1.8V is not connected
TEBA0841
Overview
Content Tools