Versions Compared

Old Version 36

changes.mady.by.user Jan Kumann

Saved on

compared with

New Version Current

changes.mady.by.user Andrei Errapart

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Scroll pdf ignore

Table of Contents

Overview


Scroll Only (inline)
Refer to https://wiki.trenz-electronic.de/display/PD/EDPS+User+Manual for online version of this manual and additional technical documentation of the product.

This...The Electric Drive Power Stage (EDPS) Board, a Trenz Electronic TEC0053, is to be used together with the Controller Board for the evaluation of Motor Control.


Key Features

  • Evaluation of the Motor control Control with the a suitable controller boardController Board 
  • Power option up to 48V and 30A main supply current
  • MOSFET power stage supporting 3-phase BLDC motors
  • Current measurement on 2-phases (3 phase measurement is optional)
  • On-board temperature sensor and 1-wire bus connector for additional sensors
  • Encoder input capable of receiving both single ended and differential signals

Figure 1: Top view of the EDPS Board PCB.

EDPS Block Diagram

Figure 2: Block diagram of the boardEDPS Board.

General Safety Instructions

  • This product should be operated only by qualified electrical specialist only.
  • Never leave an operating board unattended.
  • There is a possible risk of burns due to the hot surfaces while operating the Board. Reason for this could be an EDPS Board because of the high currents present in the motor driving outputspower stage heating the board surfaces and the board components.
  • All externally connected power sources must be SELV protected (Separated or Safety Extra Low Voltage).
  • All wiring and installation should be performed only with all external power sources switched OFF or disconnected.
  • No wiring or mechanical setup changes should be performed while the board is operating.
  • The product is rated for dry indoor , dry environment use only.
  • The product is intended to be used only in horizontal position on a non-conducting and non-inflammable surface.
  • The mechanical setup must ensure that the board and all of its parts are firmly fixed in place to prevent accidental or unwanted movement(e.g. sliding, falling. etc.).

Signals, Interfaces and Pins

Control Board

...

Connectors

Image Modified

Figure 3: PCB connectors J8 and J9.

...

Signal namesConnector J8Connector J9Connector J17

Digital Supply to EDPS

Pin 6, 12: +3.3V
Pin 5, 11: GND

Pin 6, 12: +3.3V
Pin 5, 11: GND		Pin 5, 6, 21, 22: +3.3V
Pin 1, 2, 25, 26: GND

Motor Driver PWM Signals to EDPS

High and Low Side control signals
are hardware protected against
simultaniously simultaneously ON switching
of the MOSFETs

 

Pin 1: G1H - Ch.A HighSide
Pin 7: G1L - Ch.A LowSide
Pin 2: G2H - Ch.B HighSide
Pin 8: G2L - Ch.B LowSide
Pin 3: G3H - Ch.C HighSide
Pin 9: G3L - Ch.C LowSide

 

Pin 11: G1H - Ch.A HighSide
Pin 12: G1L - Ch.A LowSide
Pin 9: G2H - Ch.B HighSide
Pin 10: G2L - Ch.B LowSide
Pin 7: G3H - Ch.C HighSide
Pin 8: G3L - Ch.C LowSide

ADC Clock Signal to EDPS Pin 1: SCLKPin 23: SCLK
Encoder Digital Signals from EDPS 

Pin 8: ENC_A
Pin 9: ENC_B
Pin 10: ENC_I

Pin 20: ENC_A
Pin 18: ENC_B
Pin 16: ENC_I

Motor Current ADC "raw" Signals from EDPS
(usable with FPGA IP)		 

Pin 2: SDI1 - Current Ch.A
Pin 3: SDI2 - Current Ch.B
Pin 4: SDI3 - Current Ch.C

Pin 19: SDI1 - Current Ch.A
Pin 17: SDI2 - Current Ch.B
Pin 15: SDI3 - Current Ch.C

Supply Voltage ADC "raw" Signal from EDPS
(usable with FPGA IP)		 

Pin 7: SDIV - from DC_LINK
(Fused Motor Supply Voltage)

Pin 24: SDIV - from DC_LINK
(Fused Motor Supply Voltage)

1-Wire bus for temperature measurementPin 10: EXT1 - 1-Wire Bus 1
Pin 4: EXT2 - 1-Wire Bus 2		 

Pin 4: EXT1 - 1-Wire Bus 1
Pin 3: EXT2 - 1-Wire Bus 2

Pins not connectedNoneNonePin 13, 14

...

External power supply for the motor must be SELV (Separated or safety extra-low voltage) protected.This option is

  • only allowed to be used for electrical specialist for the used electrical voltage and power conditions
  • only allowed to be used under electrical laboratory conditions
  • only allowed to be used in horizontal position on a non-conducting and non-inflammable surface
  • only allowed to be used with a wiring, which fulfills the current rating for the maximum possible currents.
  • only allowed to be used with a suitable current limiting circuit The such that the maximum continuous current must does not exceed 30A as follows:
      .
    • The delivered fuse "Littelfuse Tpye Type 142.5631.5302" must be used as current limiter between connector connectors J5 and J6.
    • To limit the current for smaller motor loads an ADDITIONALLY ADDITIONALL appropriate current limiter can be used e.g. a current limited power source or a fuse integrated in the wiring.
  • only allowed to be used with appropriate connectors at the M5 screw connectors, which means M5 cable lugs must be used and fastened according to technical standards.

  • only allowed to be used, if the

    "Drive Boad

    high current

    signals"

    parts conducting up to 30A nominal, are covered by isolating, mechanically stable, non-inflammable (UL V-1 or better) material


    . The

    "Drive Board

    high current

    signals" are

    parts are shown on the following picture:

Image Added

Figure 5: The high current parts on the EDPS Board, the motor outputs A, B, C

...

, fuse F1 Connectors J5

...

, J6 and further internal connections

...

, are marked white.

Image Removed

Figure 5.

Warning
It is mandatory to use the delivered isolating cover of the PCB made of plexiglass as a minimum protection. Use holes H1, H9, H3 and H4 with the delivered 10mm spacers when mounting.


Image Modified

Figure 6: Top view of the EDPS Board with isolating transparent plexiglass cover attached.

Figure 7: Side view of the EDPS Board with isolating plexiglass cover.

...

The cable lugs used should be isolated in the outer border area of the Drive EDPS Board.

Make sure that the Isolating PCB Cover is overlapping the conducting material by a minimum of 20 mm.

Initial Operation

To use a separate power supply for the motor supply perform the following steps:

Prepare the EDPS board as follows:

  1. In the case of low-powered motors and/or low-powered power supply it is recommended to use additional current limiter circuit or additional fuseDisconnect the reference motor board TEC0060 by unmounting its screws and the encoder cable from J10.
  2. Mount the delivered 30A fuse to the connectors J5 and J6 with the delivered M5 screws.For lower supply current requirements
  3. Use at most 3m long cable with lugs to connect the positive terminal of the used motor a fuse with a suitable lower current rating integrated in the supply wiring is recommended.Connect with cable lugs the DC of motor power supply to J6 (DC +5..48V to J6 ) and the corresponding GND negative terminal to J1 (0V).
  4. The cable length is limited to 3m.
  5. Connect Use at most 3m long cable to connect the three motor phases to J2 (A), J3 (B) and J4 (C).The cable length is limited to 3m
  6. Connect 12V power supply to J7 (12V). In the case motor power supply voltage is 12V as well, one power supply can be used.
  7. Optional: Connect the encoder to J10 or J11 and set jumper field J13 according to the signal specification (either to differential or to single ended )configuration.

Power-On Sequence

Any power sequence of the three supply sources is allowed:

  • +3V3 Supply from the Control Board, generated by Control Board supply
  • +12V and
  • Optional +5..48V Motor Supply

...

Adapter Board TEC0060

For easy connection of the reference Reference Motor and Encoder to the Driver EDPS Board a special Motor Adapter Board TEC0060 is included in the EDDP Kit.

Image Modified

Figure 8: Reference Motor Adapter Board TEC0060 with the Reference Motor and Plastic DEMO load attached.

Reference Motor

The reference motor is Reference Motor and Encoder are manufactured by Anaheim Automation. The order code for the motor with the encoder already mounted is BLWR111D-24V-10000-1000SI. Please note that the encoder is not available separately. The nominal motor voltage is DC 24V, however, only 12V is supplied by the Reference Motor Board, which results in reduced performance.

...

Technical Specifications

Absolute Maximum Ratings

ParameterMinMax

Units

Notes

DC +12V supply

015

V

 
DC +5..48V supply050VV 
DC +3V3 supply-0.56V 
PWM Input-0.56V 
ADC Digital Input-0.53.8V
DC +3V3 =
Assuming digital power supply voltage is at 3.3V
Encoder Input-1015V 

Table 3: Absolute maximum ratings.

Recommended Operating Conditions

ParameterMinMax

Units

Notes

DC +12V supply

11.512.5

V

 

DC +5..48V supply548V
 
DC +3V3 supply3.03.6V
 
PWM Input0DC +3V3 supplyV
 
ADC Digital Input0DC +3V3 supplyV
 
Encoder Input-712V
 

Table 4: Recommended oprating conditions.

Scroll Pagebreak

Electrical characteristics

DC +3V3 supply = 3.3V

ParameterMinMax

Units

Notes
PWM Input Logic High Level2.2 V 
PWM Input Logic Low Level 0.8V 
ADC Digital Input Logic High Level2.7 V 
ADC Digital Input Logic Low Level 0.6V 
ADC Digital Output Logic High Level3.23.3VIo=-200μA
ADC Digital Output Logic Low Level00.4VIo=+200μA
Encoder Input Logic High Level (Differential) -0.2V 
Encoder Input Logic Low Level (Differential)-0.01 V 
Encoder Input Logic High Level (Single
Ended
ended)2 V 
Encoder Input Logic Low Level (Single
Ended
ended) 0.6V 

Table 5: Electrical characteristics.

...

  • Board size: 100 mm × 166 mm.  Please download the assembly diagram for the exact numbers.

  • PCB thickness: 1.75 mm +/-10%

  • Highest part on PCB: approximately 17 mm. Please download the step model for the exact numbers.

All dimensions are shown in millimeters. Additional sketches, drawings and schematics can be found here.

Figure 9: Physical Dimensions of the TEC0060 boardEDPS Board.

Operating Temperature Ranges

...

Date

Revision

Authors

Description

Page info
modified-date
modified-date
dateFormatyyyy-MM-dd



Jan KumannGeneral formatting changes and small corrections.
2017-ß808-14

v.10

Antti Lukats, Andrei ErrapartInitial version.

...

Table 7: Document change history.

...