Page History

...

SFP+ 2x1 cage with integrated LED light pipes, J9
DisplayPort connector, J12
USB3 A 2x , RJ45 1x (stacked), J13
FMC connector (FMC B), J4
FMC B cooling fan, M2
FMC connector (FMC C), J8
FMC C cooling fan, M3
FMC connector (FMC D), J7
FMC D cooling fan, M4
FMC connector (FMC E), J6
FMC E cooling fan, M5
I²C programming header of on-board PLL clock generator U17, J22
4-Wire PWM fan connector, J23
Main Power Jack 24V, J1
CAN bus D-SUB 9-pin male connector, J3
CAN bus 6-pin header male, J15
XMOD JTAG header for access to System Controller CPLD, J35
XMOD JTAG header for access to Zynq MPSoC, J24
4-Wire PWM fan connector, J33
Battery Holder CR1220, B1
SMA coaxial connector (PLL Si5345A U17 clock input), J25
Push Button, S1
Push Button, S2
DDR4 SO-DIMM socket, U3
4-bit DIP-switch, S4
4-bit DIP-switch, S3
FMC connector (FMC A), J10
FMC A cooling fan, M1
FMC connector (FMC F), J21
FMC F cooling fan, M6
NGFF M.2 PCIe socket (Key M), U2
SD Card socket, J11
User LEDs (3x green, 1x red) with LED light pipe, D13 ... D16
Green LEDs dedicated to USB3 hub U4, D17 ... D19
Red LED indicating FPGAs 'DONE' signal, D6
4-Wire PWM fan connector, J2
Xilinx Zynq Ultrascale+ MPSoC, U1

Initial Delivery State

Storage device name	Content	Notes
User configuration EEPROMs (1x Microchip 24LC128-I/ST, 3x Microchip 24AA025E48T-I/OT)	Empty	Not programmed
USB3 HUB Configuration EEPROM (Microchip 24LC128-I/ST)	Empty	Not programmed
Si5338A programmable PLL NVM OTP	Empty	Not programmed
Si5345A programmable PLL NVM OTP	Empty	Not programmed
eMMC Flash memory	Empty	Not programmed
2x QSPI Flash memory	Empty	Not programmed

...

HTML
<!-- MGT lanes should be listed separately, as they are more specific than just general I/Os. -->

Following tables contains information about the interfaces, I/O's, clock and VCCIO sources available on the FMC connectors A - F:

Anchor

	FMC A
	FMC A

FMC A

FMC A Interfaces:

FMC	Interfaces	I/O Signal Count	LVDS-pairs count	Connected to	VCCO bank Voltage	Notes
J10 (FMC A)	I/O	12	6	Bank 44 HD	FMCAF_1V8	-
	I/O	56	28	SC CPLD U27 Bank 1	FMCAF_1V8	-
	I²C	2	-	I²C-Switch U37	-	Muxed to MIO Bank 501 I²C Inteface
	JTAG	4	-	SC CPLD U27 Bank 2	3.3VSB	-
	MGT	-	8 (4 x RX/TX)	Bank 128 GTH	-	4x MGT lanes
	Clock Input	-	1	Bank 128 GTH	-	1x Reference clock input to MGT bank
	Control Signals	3	-	SC CPLD U27 Bank 0	3.3VSB	'FMCA_PG_C2M', 'FMCA_PG_M2C', 'FMCA_PRSNT'

Table 3: FMC A connector interfaces

FMC A MGT Lanes:

FMC	MGT Lane	Bank	Type	Signal Schematic Name	FMC Connector Pin	FPGA Pin
J10 (FMC A)	0	128	GTH	B128_RX0_P B128_RX0_N B128_TX0_P B128_TX0_N	J10-C6 J10-C7 J10-C2 J10-C3	MGTHRXP0_128, T33 MGTHRXN0_128, T34 MGTHTXP0_128, T29 MGTHTXN0_128, T30
	1	128	GTH	B128_RX1_P B128_RX1_N B128_TX1_P B128_TX1_N	J10-A2 J10-A3 J10-A22 J10-A23	MGTHRXP1_128, P33 MGTHRXN1_128, P34 MGTHTXP1_128, R31 MGTHTXN1_128, R32
	2	128	GTH	B128_RX2_P B128_RX2_N B128_TX2_P B128_TX2_N	J10-A6 J10-A7 J10-A26 J10-A27	MGTHRXP2_128, N31 MGTHRXN2_128, N32 MGTHTXP2_128, P29 MGTHTXN2_128, P30
	3	128	GTH	B128_RX3_P B128_RX3_N B128_TX3_P B128_TX3_N	J10-A10 J10-A11 J10-A30 J10-A31	MGTHRXP3_128, M33 MGTHRXN3_128, M34 MGTHTXP3_128, M29 MGTHTXN3_128, M30

Table 4: FMC A connector MGT lanes

FMC A Clock Signals:

FMC

Signal Schematic Name

Bank

FMC Connector Pin

FPGA Pin

Notes

J10

(FMC A)

B128_CLK0_P
B128_CLK0_N

128

J10-D4
J10-D5

MGTREFCLK0P_128, R27
MGTREFCLK0N_128, R28

Supplied by attached module

Table 5: FMC A connector clock signal input

FMC A VCC/VCCIO:

FMC	Available VCC/VCCIO	FMC Connector Pin	Source	Notes
J10 (FMC A)	FMCA_3V3	J10-D36 J10-D38 J10-D40 J10-C39	DCDC U32, max. cur.: 5A	Enable by SC CPLD U27, bank 2, pin Y18 Signal: 'EN_A_3V3'
	3V3SB	J10-D32	DCDC U50, max. cur.: 1A	not dedicated for FMC connectors
	12V_FMC_AF	J10-C35 J10-C37	DCDC U51, max. cur.: 5A	-
	FMCAF_1V8	J10-H40 J10-G39 J10-F40 J10-E39	DCDC U39, max. cur.: 5A	Enable by SC CPLD U27, bank 2, pin W19 Signal: 'EN_AF_1V8'

Table 6: FMC A connector available VCC/VCCIO

FMC A Cooling Fan:

FMC

Fan Designator

Enable Signal

Notes

J10

(FMC A)

M1

Enable by SC CPLD U27, bank 2, pin Y19
Signal: 'FAN_A_EN'

-

Table 7: FMC A connector cooling fan

Anchor

	FMC F
	FMC F

FMC F

FMC F Interfaces:

FMC	Interfaces	I/O Signal Count	LVDS-pairs count	Connected to	VCCO bank Voltage	Notes
J21 (FMC F)	I/O	12	6	Bank 44 HD	FMCAF_1V8	-
		28	14	SC CPLD U27 Bank 1	FMCAF_1V8	-
		28	14	SC CPLD U27 Bank 3	FMCAF_1V8	-
	I²C	2	-	I²C-Switch U37	-	Muxed to MIO Bank 501 I²C Inteface
	JTAG	4	-	SC CPLD U27 Bank 2	3.3VSB	-
	MGT	-	4 (2 x RX/TX)	Bank 129 GTH	-	2x MGT lanes
	Clock Input	-	1	Bank 129 GTH	-	1x Reference clock input to MGT bank
	Control Signals	3	-	SC CPLD U27 Bank 2	3.3VSB	'FMCF_PG_C2M', 'FMCF_PG_M2C', 'FMCF_PRSNT'

Table 8: FMC F connector interface

FMC F MGT Lanes:

FMC

MGT Lane

Bank

Type

Signal Schematic Name

FMC Connector Pin

FPGA Pin

J21

(FMC F)

0

129

GTH

B129_RX0_P
B129_RX0_N
B129_TX0_P
B129_TX0_N

J21-C6
J21-C7
J21-C2
J21-C3

MGTHRXP0_129, L31
MGTHRXN0_129, L32
MGTHTXP0_129, K29
MGTHTXN0_129, K30

1

129

GTH

B129_RX1_P
B129_RX1_N
B129_TX1_P
B129_TX1_N

J21-A2
J21-A3
J21-A22
J21-A23

MGTHRXP1_129, K33
MGTHRXN1_129, K34
MGTHTXP1_129, J31
MGTHTXN1_129, J32

Table 9: FMC F connector MGT lanes

FMC F Clock Signals:

FMC

Signal Schematic Name

Bank

FMC Connector Pin

FPGA Pin

Notes

J21

(FMC F)

B129_CLK0_P
B129_CLK0_N

129

J21-D4
J21-D5

MGTREFCLK0P_129, L27
MGTREFCLK0N_129, L28

Supplied by attached module

Table 10: FMC F connector clock signal input

FMC F VCC/VCCIO:

FMC	Available VCC/VCCIO	FMC Connector Pin	Source	Notes
J21 (FMC F)	FMCF_3V3	J21-D36 J21-D38 J21-D40 J21-C39	DCDC U42, max. cur.: 5A	Enable by SC CPLD U27, bank 2, pin Y10 Signal: 'EN_F_3V3'
	3V3SB	J21-D32	DCDC U50, max. cur.: 1A	not dedicated for FMC connectors
	12V_FMC_AF	J21-C35 J21-C37	DCDC U51, max. cur.: 5A	-
	FMCAF_1V8	J21-H40 J21-G39 J21-F40 J21-E39	DCDC U39, max. cur.: 5A	Enable by SC CPLD U27, bank 2, pin W19 Signal: 'EN_AF_1V8'

Table 11: FMC F connector available VCC/VCCIO

FMC F Cooling Fan:

FMC

Fan Designator

Enable Signal

Notes

J21

(FMC F)

M6

Enable by SC CPLD U27, bank 2, pin W18
Signal: 'FAN_F_EN'

-

Table 12: FMC F connector cooling fan

Anchor

	FMC B
	FMC B

FMC B

FMC B Interfaces:

FMC	Interfaces	I/O Signal Count	LVDS-pairs count	Connected to	VCCO bank Voltage	Notes
J4 (FMC B)	I/O	24	12	Bank 47 HD	FMCBC_1V8	-
		20	10	Bank 48 HD	FMCBC_1V8	-
		24	12	Bank 49 HD	FMCBC_1V8	-
	I²C	2	-	I²C-Switch U13	-	Muxed to MIO Bank 501 I²C Inteface
	JTAG	4	-	SC CPLD U27 Bank 0	3.3VSB	-
	MGT	-	8 (4 x RX/TX)	Bank 130 GTH	-	4x MGT lanes
	Clock Input	-	2	Bank 48 HD	-	2x Reference clock inputs to PL bank
	Clock Input	-	1	Bank 130 GTH	-	1x Reference clock input to MGT bank
	Control Signals	3	-	SC CPLD U27 Bank 0	3.3VSB	'FMCB_PG_C2M', 'FMCB_PG_M2C', 'FMCB_PRSNT'

Table 13: FMC B connector interfaces

FMC B MGT Lanes:

FMC	MGT Lane	Bank	Type	Signal Schematic Name	FMC Connector Pin	FPGA Pin
J4 (FMC B)	3	130	GTH	B130_RX3_P B130_RX3_N B130_TX3_P B130_TX3_N	J4-C6 J4-C7 J4-C2 J4-C3	MGTHRXP3_130, B33 MGTHRXN3_130, B34 MGTHTXP3_130, A31 MGTHTXN3_130, A32
	2	130	GTH	B130_RX2_P B130_RX2_N B130_TX2_P B130_TX2_N	J4-A2 J4-A3 J4-A22 J4-A23	MGTHRXP2_130, C31 MGTHRXN2_130, C32 MGTHTXP2_130, B29 MGTHTXN2_130, B30
	1	130	GTH	B130_RX1_P B130_RX1_N B130_TX1_P B130_TX1_N	J4-A6 J4-A7 J4-A26 J4-A27	MGTHRXP1_130, D33 MGTHRXN1_130, D34 MGTHTXP1_130, D29 MGTHTXN1_130, D30
	0	130	GTH	B130_RX0_P B130_RX0_N B130_TX0_P B130_TX0_N	J4-A10 J4-A11 J4-A30 J4-A31	MGTHRXP0_130, E31 MGTHRXN0_130, E32 MGTHTXP0_130, F29 MGTHTXN0_130, F30

Table 14: FMC B connector MGT lanes

FMC B Clock Signals:

FMC

Signal Schematic Name

Bank

FMC Connector Pin

FPGA Pin

Notes

J4

(FMC B)

B130_CLK0_P
B130_CLK0_N

130

J4-D4
J4-D5

MGTREFCLK0P_130, G27
MGTREFCLK0N_130, G28

Supplied by attached module

B_CLK0_M2C_P
B_CLK0_M2C_N

48 HD

J4-H4
J4-H5

IO_L6P_HDGC_48, F17
IO_L6N_HDGC_48, F18

Supplied by attached module

B_CLK1_M2C_P
B_CLK1_M2C_N

48 HD

J4-G2
J4-G3

IO_L5P_HDGC_48, G18
IO_L5N_HDGC_48, G19

Supplied by attached module

Table 15: FMC B connector clock signal input

FMC B VCC/VCCIO:

FMC	Available VCC/VCCIO	FMC Connector Pin	Source	Notes
J4 (FMC B)	FMCB_3V3	J4-D36 J4-D38 J4-D40 J4-C39	DCDC U33, max. cur.: 5A	Enable by SC CPLD U27, bank 0, pin G11 Signal: 'EN_B_3V3'
	3V3SB	J4-D32	DCDC U50, max. cur.: 1A	not dedicated for FMC connectors
	12V	J4-C35 J4-C37	DCDC U82, max. cur.: 8A	not dedicated for FMC connectors
	FMCBC_1V8	J4-H40 J4-G39 J4-F40 J4-E39	DCDC U40, max. cur.: 5A	Enable by SC CPLD U27, bank 0, pin A3 Signal: 'EN_BC_1V8'

Table 16: FMC B connector available VCC/VCCIO

FMC B Cooling Fan:

FMC

Fan Designator

Enable Signal

Notes

J4

(FMC B)

M2

Enable by SC CPLD U27, bank 0, pin A2
Signal: 'FAN_B_EN'

-

Table 17: FMC B connector cooling fan

Anchor

	FMC C
	FMC C

FMC C

FMC C Interfaces:

FMC	Interfaces	I/O Signal Count	LVDS-pairs count	Connected to	VCCO bank Voltage	Notes
J8 (FMC C)	I/O	20	10	Bank 50 HD	FMCBC_1V8	-
	I/O	48	24	Bank 67 HP	FMCBC_1V8	-
	I²C	2	-	I²C-Switch U13	-	Muxed to MIO Bank 501 I²C Inteface
	JTAG	4	-	SC CPLD U27 Bank 2	3.3VSB	-
	MGT	-	8 (4 x RX/TX)	Bank 230 GTH	-	4x MGT lanes
	Clock Input	-	2	Bank 50 HD	-	2x Reference clock inputs to PL bank
	Clock Input	-	1	Bank 230 GTH	-	1x Reference clock input to MGT bank
	Control Signals	3	-	SC CPLD U27 Bank 2	3.3VSB	'FMCC_PG_C2M', 'FMCC_PG_M2C', 'FMCC_PRSNT'

Table 18: FMC C connector interfaces

FMC C MGT Lanes:

FMC	MGT Lane	Bank	Type	Signal Schematic Name	FMC Connector Pin	FPGA Pin
J8 (FMC C)	3	230	GTH	B230_RX3_P B230_RX3_N B230_TX3_P B230_TX3_N	J8-C6 J8-C7 J8-C2 J8-C3	MGTHRXP3_230, A4 MGTHRXN3_230, A3 MGTHTXP3_230, A8 MGTHTXN3_230, A7
	2	230	GTH	B230_RX2_P B230_RX2_N B230_TX2_P B230_TX2_N	J8-A2 J8-A3 J8-A22 J8-A23	MGTHRXP2_230, B2 MGTHRXN2_230, B1 MGTHTXP2_230, B6 MGTHTXN2_230, B5
	1	230	GTH	B230_RX1_P B230_RX1_N B230_TX1_P B230_TX1_N	J8-A6 J8-A7 J8-A26 J8-A27	MGTHRXP1_230, C4 MGTHRXN1_230, C3 MGTHTXP1_230, D6 MGTHTXN1_230, D5
	0	230	GTH	B230_RX0_P B230_RX0_N B230_TX0_P B230_TX0_N	J8-A10 J8-A11 J8-A30 J8-A31	MGTHRXP0_230, D2 MGTHRXN0_230, D1 MGTHTXP0_230, E4 MGTHTXN0_230, E3

Table 19: FMC C connector MGT lanes

FMC C Clock Signals:

FMC

Signal Schematic Name

Bank

FMC Connector Pin

FPGA Pin

Notes

J8

(FMC C)

B230_CLK0_P
B230_CLK0_N

230

J8-D4
J8-D5

MGTREFCLK0P_230, C8
MGTREFCLK0N_230, C7

Supplied by attached module

C_CLK0_M2C_P
C_CLK0_M2C_N

50 HD

J8-H4
J8-H5

IO_L7P_HDGC_50, J12
IO_L7N_HDGC_50, H12

Supplied by attached module

C_CLK1_M2C_P
C_CLK1_M2C_N

50 HD

J8-G2
J8-G3

IO_L8P_HDGC_50, H13
IO_L8N_HDGC_50, G13

Supplied by attached module

Table 20: FMC C connector clock signal input

FMC C VCC/VCCIO:

FMC	Available VCC/VCCIO	FMC Connector Pin	Source	Notes
J8 (FMC C)	FMCC_3V3	J8-D36 J8-D38 J8-D40 J8-C39	DCDC U34, max. cur.: 5A	Enable by SC CPLD U27, bank 0, pin E11 Signal: 'EN_C_3V3'
	3V3SB	J8-D32	DCDC U50, max. cur.: 1A	not dedicated for FMC connectors
	12V	J8-C35 J8-C37	DCDC U82, max. cur.: 8A	not dedicated for FMC connectors
	FMCBC_1V8	J8-H40 J8-G39 J8-F40 J8-E39	DCDC U40, max. cur.: 5A	Enable by SC CPLD U27, bank 0, pin A3 Signal: 'EN_BC_1V8'

Table 21: FMC C connector available VCC/VCCIO

FMC C Cooling Fan:

FMC

Fan Designator

Enable Signal

Notes

J8

(FMC C)

M3

Enable by SC CPLD U27, bank 0, pin B3
Signal: 'FAN_C_EN'

-

Table 22: FMC C connector cooling fan

Anchor

	FMC D
	FMC D

FMC D

FMC D Interfaces:

FMC	Interfaces	I/O Signal Count	LVDS-pairs count	Connected to	VCCO bank Voltage	Notes
J7 (FMC D)	I/O	20	10	Bank 65 HP	FMCDE_1V8	-
	I/O	48	24	Bank 66 HP	FMCDE_1V8	-
	I²C	2	-	I²C-Switch U13	-	Muxed to MIO Bank 501 I²C Inteface
	JTAG	4	-	SC CPLD U27 Bank 2	3.3VSB	-
	MGT	-	8 (4 x RX/TX)	Bank 229 GTH	-	4x MGT lanes
	Clock Input	-	2	Bank 65 HP	-	2x Reference clock inputs to PL bank
	Clock Input	-	1	Bank 229 GTH	-	1x Reference clock input to MGT bank
	Control Signals	3	-	SC CPLD U27 Bank 2	3.3VSB	'FMCD_PG_C2M', 'FMCD_PG_M2C', 'FMCD_PRSNT'

Table 23: FMC D connector interfaces

FMC D MGT Lanes:

FMC	MGT Lane	Bank	Type	Signal Schematic Name	FMC Connector Pin	FPGA Pin
J7 (FMC D)	3	229	GTH	B229_RX3_P B229_RX3_N B229_TX3_P B229_TX3_N	J7-C6 J7-C7 J7-C2 J7-C3	MGTHRXP3_229, F2 MGTHRXN3_229, F1 MGTHTXP3_229, F6 MGTHTXN3_229, F5
	2	229	GTH	B229_RX2_P B229_RX2_N B229_TX2_P B229_TX2_N	J7-A2 J7-A3 J7-A22 J7-A23	MGTHRXP2_229, H2 MGTHRXN2_229, H1 MGTHTXP2_229, G4 MGTHTXN2_229, G3
	1	229	GTH	B229_RX1_P B229_RX1_N B229_TX1_P B229_TX1_N	J7-A6 J7-A7 J7-A26 J7-A27	MGTHRXP1_229, J4 MGTHRXN1_229, J3 MGTHTXP1_229, H6 MGTHTXN1_229, H5
	0	229	GTH	B229_RX0_P B229_RX0_N B229_TX0_P B229_TX0_N	J7-A10 J7-A11 J7-A30 J7-A31	MGTHRXP0_229, K2 MGTHRXN0_229, K1 MGTHTXP0_229, K6 MGTHTXN0_229, K5

Table 24: FMC D connector MGT lanes

FMC D Clock Signals:

FMC

Signal Schematic Name

Bank

FMC Connector Pin

FPGA Pin

Notes

J7

(FMC D)

B229_CLK0_P
B229_CLK0_N

229

J7-D4
J7-D5

MGTREFCLK0P_229, G8
MGTREFCLK0N_229, G7

Supplied by attached module

D_CLK0_M2C_P
D_CLK0_M2C_N

65 HP

J7-H4
J7-H5

IO_L14P_T2L_N2_GC_65, AG5
IO_L14N_T2L_N3_GC_65, AG4

Supplied by attached module

D_CLK1_M2C_P
D_CLK1_M2C_N

65 HP

J7-G2
J7-G3

IO_L13P_T2L_N0_GC_QBC_65, AE5
IO_L13N_T2L_N1_GC_QBC_65, AF5

Supplied by attached module

Table 25: FMC D connector clock signal input

FMC D VCC/VCCIO:

FMC	Available VCC/VCCIO	FMC Connector Pin	Source	Notes
J7 (FMC D)	FMCD_3V3	J7-D36 J7-D38 J7-D40 J7-C39	DCDC U35, max. cur.: 5A	Enable by SC CPLD U27, bank 0, pin F8 Signal: 'EN_D_3V3'
	3V3SB	J7-D32	DCDC U50, max. cur.: 1A	not dedicated for FMC connectors
	12V	J7-C35 J7-C37	DCDC U82, max. cur.: 8A	not dedicated for FMC connectors
	FMCDE_1V8	J7-H40 J7-G39 J7-F40 J7-E39	DCDC U41, max. cur.: 5A	Enable by SC CPLD U27, bank 0, pin C5 Signal: 'EN_DE_1V8'

Table 26: FMC D connector available VCC/VCCIO

FMC D Cooling Fan:

FMC

Fan Designator

Enable Signal

Notes

J7

(FMC D)

M4

Enable by SC CPLD U27, bank 0, pin D7
Signal: 'FAN_D_EN'

-

Table 27: FMC D connector cooling fan

Anchor

	FMC E
	FMC E

FMC E

FMC E Interfaces:

FMC	Interfaces	I/O Signal Count	LVDS-pairs count	Connected to	VCCO bank Voltage	Notes
J6 (FMC E)	I/O	24	12	Bank 65 HP	FMCDE_1V8	-
	I/O	44	22	Bank 64 HP	FMCDE_1V8	-
	I²C	2	-	I²C-Switch U13	-	Muxed to MIO Bank 501 I²C Inteface
	JTAG	4	-	SC CPLD U27 Bank 2	3.3VSB	-
	MGT	-	8 (4 x RX/TX)	Bank 228 GTH	-	4x MGT lanes
	Clock Input	-	2	Bank 64 HP	-	2x Reference clock inputs to PL bank
	Clock Input	-	1	Bank 228 GTH	-	1x Reference clock input to MGT bank
	Control Signals	3	-	SC CPLD U27 Bank 2	3.3VSB	'FMCE_PG_C2M', 'FMCE_PG_M2C', 'FMCE_PRSNT'

Table 28: FMC E connector interfaces

FMC E MGT Lanes:

FMC	MGT Lane	Bank	Type	Signal Schematic Name	FMC Connector Pin	FPGA Pin
J6 (FMC E)	3	228	GTH	B228_RX3_P B228_RX3_N B228_TX3_P B228_TX3_N	J6-C6 J6-C7 J6-C2 J6-C3	MGTHRXP3_228, L4 MGTHRXN3_228, L3 MGTHTXP3_228, M6 MGTHTXN3_228, M5
	2	228	GTH	B228_RX2_P B228_RX2_N B228_TX2_P B228_TX2_N	J6-A2 J6-A3 J6-A22 J6-A23	MGTHRXP2_228, M2 MGTHRXN2_228, M1 MGTHTXP2_228, N4 MGTHTXN2_228, N3
	1	228	GTH	B228_RX1_P B228_RX1_N B228_TX1_P B228_TX1_N	J6-A6 J6-A7 J6-A26 J6-A27	MGTHRXP1_228, P2 MGTHRXN1_228, P1 MGTHTXP1_228, P6 MGTHTXN1_228, P5
	0	228	GTH	B228_RX0_P B228_RX0_N B228_TX0_P B228_TX0_N	J6-A10 J6-A11 J6-A30 J6-A31	MGTHRXP0_228, T2 MGTHRXN0_228, T1 MGTHTXP0_228, R4 MGTHTXN0_228, R3

Table 29: FMC E connector MGT lanes

FMC E Clock Signals:

FMC

Signal Schematic Name

Bank

FMC Connector Pin

FPGA Pin

Notes

J6

(FMC E)

B228_CLK0_P
B228_CLK0_N

228

J6-D4
J6-D5

MGTREFCLK0P_228, L8
MGTREFCLK0N_228, L7

Supplied by attached module

E_CLK0_M2C_P
E_CLK0_M2C_N

64 HP

J6-H4
J6-H5

IO_L12P_T1U_N10_GC_64, AL8
IO_L12N_T1U_N11_GC_64, AL7

Supplied by attached module

E_CLK1_M2C_P
E_CLK1_M2C_N

64 HP

J6-G2
J6-G3

IO_L11P_T1U_N8_GC_64, AK8
IO_L11N_T1U_N9_GC_64, AK7

Supplied by attached module

Table 30: FMC E connector clock signal input

FMC E VCC/VCCIO:

FMC	Available VCC/VCCIO	FMC Connector Pin	Source	Notes
J6 (FMC E)	FMCE_3V3	J6-D36 J6-D38 J6-D40 J6-C39	DCDC U36, max. cur.: 5A	Enable by SC CPLD U27, bank 0, pin E8 Signal: 'EN_E_3V3'
	3V3SB	J6-D32	DCDC U50, max. cur.: 1A	not dedicated for FMC connectors
	12V	J6-C35 J6-C37	DCDC U82, max. cur.: 8A	not dedicated for FMC connectors
	FMCDE_1V8	J6-H40 J6-G39 J6-F40 J6-E39	DCDC U41, max. cur.: 5A	Enable by SC CPLD U27, bank 0, pin C5 Signal: 'EN_DE_1V8'

Table 31: FMC E connector available VCC/VCCIO

FMC E Cooling Fan:

FMC

Fan Designator

Enable Signal

Notes

J6

(FMC E)

M5

Enable by SC CPLD U27, bank 0, pin D6
Signal: 'FAN_E_EN'

-

Table 32: FMC E connector cooling fan

XMOD JTAG Interface

JTAG access to the Zynq MPSoC and SC CPLD is provided through XMOD header J24 and J35:

...

Scroll Title

anchor	Figure_10
title	Figure 10: DDR4 memory interface

Scroll Ignore

draw.io Diagram

border	false
viewerToolbar	true

fitWindow	false
diagramName	DDR4 memory interface diagram formatted
simpleViewer	false
width
links	auto
tbstyle	hidden
lbox	true
diagramWidth	641
revision	2

Scroll Only

Following table gives an overview about the I/O signals of the DDR4 SDRAM memory interface:

Connector	DDR4 SDRAM I/O Signal	Signal Schematic Name	Connected to	Notes
DDR4 SO-DIMM Socket U13	Address inputs	DDR4-A0 ... DDR4-A16	PS DDR Bank 504	-
	Bank address inputs	DDR4-BA0 / DDR4-BA1		-
	Bank group inputs	DDR4-BG0 / DDR4-BG1		-
	Differential clocks	DDR4-CLK0_P DDR4-CLK0_N DDR4-CLK1_P DDR4-CLK1_N		2 x DDR4 clock
	Data input/output	DQ0 ... DQ63		-
	Check bit input/output	CB0 ... CB7		-
	Data strobe (differential)	DDR4-DQS0_P DDR4-DQS0_N ... DDR4-DQS8_P DDR4-DQS8_N		-
	Data mask and data bus inversion	DDR4-DM0 ... DDR4-DM8		-
	Serial address inputs	DDR4-SA0 ... DDR4-SA2		address range configuration on I²C bus
	Control Signals	DDR4-CS_N0 / DDR4-CS_N1		chip selest signal
		DDR4-ODT0 / DDR4-ODT1		On-die termination enable
		DDR4-RESET		nRESET
		DDR4-PAR		Command and address parity input
		DDR4-CKE0 / DDR4-CKE1		Clock enable
		DDR4-ALERT		CRC error flag
		DDR4-ACT		Activation command input
		DDR4-EVENT		Temperature event
	I²C	DDR4-SCL DDR4-SDA	8-channel I²C switch U37	-

Table 40: DDR4 64-bit memory interface signals and pins

Refer to the Xilinx Zynq UltraScale+ datasheet DS925 for more information on whether the specific package of the Zynq UltraScale+ MPSoC supports the maximum data transmission rate of 2400 MByte/s, which also depends on the used SO-DIMM module.

...

Scroll Title

anchor	Figure_11
title	Figure 11: CAN interface

Scroll Ignore

draw.io Diagram

border	false
viewerToolbar	true

fitWindow	false
diagramName	CAN interface diagram formatted
simpleViewer	false
width
links	auto
tbstyle	hidden
lbox	true
diagramWidth	641
revision	3

Scroll Only

The CAN interface of external devices can be connected via D-SUB 9-pin male connector J3 or to the 6-pin male header J15:

Connector	Signal Schematic Name	Connected to	Notes
D-SUB 9-pin male connector J3	CAN_H	CAN Transceiver U48, pin 7	-
D-SUB 9-pin male connector J3	CAN_L	CAN Transceiver U48, pin 6	-
6-pin male header J15	CAN_H	CAN Transceiver U48, pin 7	-
6-pin male header J15	CAN_L	CAN Transceiver U48, pin 6	-
CAN Transceiver	Signal Schematic Name	Connected to	Notes
TCAN337 U48	CAN_TX	SC CPLD U27, bank 0, pin C16	3.3V VCCIO
	CAN_RX	SC CPLD U27, bank 0, pin B15	3.3V VCCIO
	CAN_S	SC CPLD U27, bank 0, pin C15	3.3V VCCIO
	CAN_FAULT	SC CPLD U27, bank 0, pin D15	3.3V VCCIO

Table 41: CAN interface signals and pins

SD Card Interface

The SD Card interface of the TEB0911 board is routed via SD IO interface to the PS MIO bank 501 of the Zynq Ultrascale+ MPSoC (3.3V VCCO). The SC CPLD U27 controls the load switch Q3 to enable the card sockets J11 with signal 'SD_EN', bank 2, pin U11. The "Card Detect" and "Write Protect" signal are also routed to the SC CPLD:

...

Connector

Signal Schematic Name

Connected to

Notes

Pin Header

J22

PLL_SCL

clock generator U17, pin 16

PS_1V8 VCCIO

PLL_SDA

clock generator U17, pin 18

SMA Coax

J25

CLK_PLL_IN

clock generator U17, pin 1

-

Table 44: Clock generator Si5345A external interfaces

On-board Peripherals

HTML
<!-- Components on the Module, like Flash, PLL, PHY... -->

...

Date

Revision

Contributors

Description

Page info

	modified-date
	modified-date
dateFormat	yyyy-MM-dd

Page info

infoType	Current version
dateFormat	yyyy-MM-dd
prefix	v.
type	Flat

Page info

infoType	Modified by
type	Flat
showVersions	false

typo

2019-05-10

v.183

John Hartfiel

correction of J8 Pin count description

2018-07-23

v.182

Ali Naseri

Initial document

--

all

Page info

infoType	Modified users
type	Flat
showVersions	false

...

Trenz Electronic Documentation

Versions Compared

Old Version 184

New Version 185

Key

Initial Delivery State

XMOD JTAG Interface

SD Card Interface

On-board Peripherals