Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Page properties
hiddentrue
idComments

Template Revision 1.1

For carrier - module combination, create main getting started page for carrier Design Name always "TE Series Name" +Getting Started, for example "TE0701 Getting started" and add carrier/module combination in the description → link on the module resource page also

For whole board,  use the board name, for example "TEBF0911 Getting Started"

  • Change List 1.0 to 1.1
    • add table of content to sidebar


Page properties
hiddentrue
idComments

In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are:

  • Overview of the board (point out the LEDs, Ethernets, Switches and etc on the board overview)
  • Explain Switches functionality
  • Explain user LEDs
  • Explain the UART connection

  • Refer to the Reference Design

    Note

    For more information regarding how to draw a diagram, Please refer to "Diagram Drawing

...

...

Table of Contents

...


TEBF0808 with TE080x

Overview

Basic instructions to work with TEBF0808 and TE0808,TE0807 or TE0803.

Info

Functionality of buttons, DIP switches, LEDs depends on CPLD Firmware. Following description is only for newest firmware version, which is available on the download area


Scroll Title
anchorFigure_Overview
titleBoard Overview


Scroll Ignore
scroll-pdftrue
scroll-officetrue
scroll-chmtrue
scroll-docbooktrue
scroll-eclipsehelptrue
scroll-epubtrue
scroll-htmltrue

draw.io Diagram
border

...

false
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxtrue
revision

...

8
diagramNameTEBF0808_getting_started_overview
simpleViewertrue
width
linksauto
tbstyletop
diagramWidth641


Scroll Only

...

Image Added



NumberNote
LetterNote
1S2- Reset Button
A

P1 - PMOD 3.3V I2C Bus

2D7 - LED D7 Red (Usage: status) || D6 - LED Green (Usage: status)
BJ9 - Audio Enclosure
3S1 - Power Button
CJ26 - FAN1 12V
4J25 - Power Jack J25, 2.1mm (optional 12V power input)
DJ17 - I2C (for optional module PLL access)
5S5 - DIP Switch for Boot Mode and FMCVADJ
EJ6/15 - Firefly - GTH
6J10 - Enclosure Pin header(Reset and Power Button, HD LED (Usage: status/user) and Power LED (Usage: status/user))
F

J31 - SATA

7S4 - DIP Switch for CPLD access and power control
GJ21/22 - Firefly - loopback only
8J12 - XMOD with green dot for Module JTAG and UART, XMOD LED D4 Red used  for status information
HP3 - PMOD 3.3V I2C Bus
9J28  - XMOD for CPLD,FMC JTAG and Firmware ID over UART(need CPLD Firmware 7 or newer) , XMOD LED D4 Red used for status information
IJ34 - I2C Firefly
10FPGA Done LED (location varies slightly on different module series )
JJ35 - FAN2 12V
11J20  - ATX Power Connector (Main 12V and 5V Power supply), recommended power supply connector
KJ11 - PCIe (1x)
12D1 - SFP LED Red (Usage: status/user)
LB1 - Battery holder CR1220
13D8 - SFP LED Green (Usage: status/user)
MJ30 - PJTAG
14D17 - USB HUB LED Green (Suspend)
NJ29 - CAN (same as J24)
15D9 - SFP LED Red (Usage: status/user)
OJ5 -  FMC HPC
16D10 - SFP LED Green (Usage: status/user)
PJ19 - FAN3 5V
17J7 - ETH LED Yellow (Usage: status)
QJ24 - CAN (same as J29)
18J7 - ETH LED Green/Orange (Usage: status)
RJ27 - SD
19D4 - LED Green (Usage: status/user) || D5 - LED Red (Usage: status/user)
SJ8 - USB 3.0 (2x) Enclosure
------
TJ14 - SFP (2x)
------
UJ7 - USB 3.0 (2x), ETH (1x)
------
VJ13 - Displayport (1x)
------
WP2 - PMOD 3.3V FPG IOs
------
W(b)Bottom side: J16 - microSD

Power supply

Page properties
hiddentrue
idComments

The input power supply must be mentioned. Add Link to overview picture with connector label.


LabelDesignatorPowerDescription
Overview - 11J2012V and 5VRecommended power supply unit is PC power supply unit:
  • DIP S4-4 can be switched OFF with this power supply configuration (CPLD firmware depended)
Overview - 4J2512VOptional single 12V power supply:
  • DIP S4-4 must be switched ON with this power supply

Current depends manly on design and cooling solution.  Use Xilinx Power Estimator and/or Your Vivado Project to estimate min current.  Minimum of 3A are recommanded for basic functionality.

DIP-Switches and Push Buttons

Page properties
hiddentrue
idComments

Explain all DIP switches functionality. Add Link to overview picture with connector label.


Scroll Title
anchorTable_DIP_

...

1
titleDIP Switches

...

S4

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

...

Jumpers

...

hiddentrue
idComments

...

Overview 7DefaultDescription
S4-1OFFSoC PUDC, ON (low - internal FPGA pull ups enabled), OFF (high - internal FPGA pull ups disabled)
S4-2OFFN.C.
S4-3OFFJTAGEN  ON (CPLD access), OFF (FMC access)
S4-4ONEnable on board 5V permanently



Scroll Title
anchorTable_DIP_2
titleDIP Switches S5 (CPLD Firmware depended)

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Overview 5DefaultDescription
S5-1ON
  • ON(1), ON(2) - Default, boot from SD/microSD or SPI Flash if no SD is detected
  • OFF(1), ON(2) - Boot from eMMC
  • ON(1), OFF(2) - Boot mode  PJTAG0
  • OFF(1), OFF(2) - Boot mode main  JTAG
S5-2ON
S5-3OFFUser Input to SoC over RGPIO interface
S5-4OFFVADJ OFF(1.2V), ON(1.8V)



Scroll Title
anchorTable_BUT_

...

1
title

...

Buttons (CPLD Firmware depended)

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Overview 1;3DefaultDescription
S2High

Negative Reset Button, alternative Enclosure over J10-7/J10-5

  • Press appr. 1sec for PS Soft Reset (PS_SRST_B)*
  • Press appr 3 sec for PS POR Reset
S1High

Negative Power Button, alternative Enclosure over J10-6/J10-8

  • Press appr. 1sec for power on/off
  • Press appr 3 sec force power of  without power down sequencing

*Note: PS_SRST_B igrnores mode pins and do not reset all registers, see UG1085 table 38-1

LEDs

Page properties
hiddentrue
idComments

Explain all user LEDs functionality and connections. Add Link to overview picture with connector label.

LEDs used different Blink Sequence to indicate all state:

Scroll Title
anchorTable_LED_SEQ
titleLED Sequencing (CPLD Firmware depended)

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Blink SequenceFrequenceNote
******** (slow blinking)~0,7 Hzcontinuous blinking, like SFP LEDs or Enclosure HD LED when board is powered down
******** (fast blinking)~5,8 Hzcontinuous blinking, like D6 LED or Enclosure Power LED when board is powered down
*****ooo~0,7 Hz, duty cycle 5/85 times fast blink with a break
****oooo~0,7 Hz, duty cycle 4/84 times fast blink with a break
***ooooo~0,7 Hz, duty cycle 3/83 times fast blink with a break
**oooooo~0,7 Hz, duty cycle 2/82 times fast blink with a break
*ooooooo~0,7 Hz, duty cycle 1/81 times fast blink with a break
ON---LED ON
OFF---LED OFF



Scroll Title
anchorTable_LED
titleCarrier LEDs (CPLD Firmware depended)

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

...

Furthermore, there are two user LEDs on module TE0728.

LabelDesignatorColorUsageDescription
Overview - 2D7Redstatus


PriorityDescriptionBlink sequencing
1PS POR Reset pressed long time (or whole system is powered off)ON
2PS Soft Reset pressed short timeOFF
3SD Boot*ooooooo
4QSPI Boot**oooooo
5eMMC Boot***ooooo
6PJTAG Boot****oooo
7JTAG Boot*****ooo
8Error******** (fast blinking)


Overview - 2D6Greenstatus


PriorityDescriptionBlink sequencing
1Power OFF******** (fast blinking)
2PG_LPD low*****ooo
3PG_FPD low****oooo
4PG_PL low***ooooo
5PG_DDR low or PG_PSGT low or PG_PLL low or PG_GT_L low or PG_GT_R low**oooooo
6POK_1V8 low or POK_FMC low or perihpery_pg low or (Main Power State Machine Ready and FMC Sanity check low)*ooooooo
7Main Power State Machine ReadyOFF
8ERROR some power failed, see XMOD LEDsON


Overview - 6J10 Power LEDBlue (symbol light bulb)status/user


PriorityDescriptionBlink sequencing
1power button pressed long time forced power down******** (fast blinking)
2

Main Power State Machine Idle and Power of State is off

******** (slow blinking)
3power button pressed short time power to power on/off*****ooo
4PS reset button pressed long time****oooo
5PS reset button pressed short time***ooooo
6power down sequencing is running**oooooo
7whole system hold into reset*ooooooo
8MIO40User Defined


Overview - 6J10 HD LED

Red (symbol drive)

status/user


PriorityDescriptionBlink sequencing
1PS Init is low******** (fast blinking)
2PS Error High*****ooo
3PS Error Status High****oooo
4SOC Done  low***ooooo
5SC0User Defined


Overview - 8XMOD1 D4Redstatus


PriorityXMOD ButtonDescriptionBlink sequencing
1Pressedpower button pressed long time forced power down******** (fast blinking)
2PressedMain Power State Machine Idle and Power of State is power down
sequencing
*****ooo
3Pressed

PS reset button pressed

****oooo
4PressedPower button pressed short time power on/off***ooooo
5PressedPower of State is power down sequencing**oooooo
6PressedSystem hold into reset*ooooooo
7PressedPS Init lowON
1UnpressedProblem with other CPLD, FMC is disabled******** (fast blinking)
2UnpressedMain Power State Machine Wait Ready ON/OFF*****ooo
3UnpressedMain Power State Machine 3.3V and VADJ ON/OFF****oooo
4Unpressedpower not ready (power reset)**oooooo
5Unpressedzynq reset*ooooooo
7UnpressedPS Init lowON
xPressed/Unpressedall fineOFF


Overview - 9XMOD2 D4Redstatus/user


PriorityDescriptionBlink sequencing
1Power On Reset********  (slow blinking)
2PS Init low******** (fast blinking)
3SC17User Defined


Overview - 12SFP D1Redstatus/user


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3RGPIO(0), when RGPIO Enabled over FPGAUser Defined
4--OFF


Overview - 13SFP D8Greenstatus/user


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3RGPIO(1), when RGPIO Enabled over FPGAUser Defined
4--OFF


Overview - 14D17 - USB HUB LED (Suspend)GreenstatusON, no USB connected, OFF, USB connected
Overview - 15SFP D9Redstatus/user


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3RGPIO(2), when RGPIO Enabled over FPGAUser Defined
4--OFF


Overview - 16SFP D10Greenstatus/user


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3RGPIO(3), when RGPIO Enabled over FPGAUser Defined
4--OFF


Overview - 17ETH J7Yellowstatus


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3ETH PHY LED(not PHY_LED0)


Overview - 18ETH J7Green/Orangestatus


PriorityDescriptionBlink sequencing
1Power On Reset******** (slow blinking)
2PS Init low******** (fast blinking)
3ETH PHY LED(PHY_LED1)


Overview - 19D4Greenstatus/user


PriorityDescriptionBlink sequencing
11.8V disabled, inter CPLD RGPIO is disabled******** (fast blinking)
21.8V enabled, inter CPLD RGPIO is disabled*****ooo
3Power On Reset****oooo
4USB Reset***ooooo
5RGPIO(4), when RGPIO Enabled over FPGAUser Defined
6all fine*ooooooo


Overview - 19D5Redstatus/user


PriorityDescriptionBlink sequencing
11.8V disabled, inter CPLD RGPIO is disabled******** (fast blinking)
21.8V enabled, inter CPLD RGPIO is disabled*****ooo
3Power On Reset****oooo
4PCie Reset***ooooo
5RGPIO(4), when RGPIO Enabled over FPGAUser Defined
6all fine*ooooooo




Scroll Title
anchorTable_LED
titleModule LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

LabelDesignatorColorConnected toDescription

...

Overview - 10D1RedDONE signal (PS Configuration Bank 503)

This LED goes ON when power has been applied to the module and stays ON until MPSoC's programmable logic is configured properly.


JTAG/UART

Page properties
hiddentrue
idComments

Explain JTAG or UART connection . Add Link to overview picture with connector label.

SoC JTAG and UART connections are available through XMOD JTAG adapter with the green dot on J12. For more information refer to TE0790.

...

There are 2 JTAG programmer on the carrier:

LabelDesignatorDescription
Overview - 8J12
  • SoC JTAG/UART over USB, UART Speed depends on design, normally 115200
  • XMOD with Xilinx Licence (green dot)
Overview - 9J28
  • CPLD or FMC JTAG over USB
  • XMOD without Xilinx Licence
  • Press Button to see Firmware ID over UART (need CPLD Firmware 7 or newer), UART Speed 115200


DIP Switch on bouth XMOD JTAG adapters must be set like on the following table.

Scroll Title
anchorTable_XMOD_JTAG
titleXMOD JTAG DIP Switch. Attention: Never changes the default setting

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

XMOD DIP SwitchSetting
1ON
2OFF
3OFF
4OFF


For more information refer to TE0790 Resources.

CPLD Firmware

Firmware Update Instruction  and CPLD description are available on TEBF0808 CPLD Firmware. Source code of the firmware is available on the download area of the TEBF0808.


Firmware Versions and some statistics can be displayed over second XMOD:

  • Included since CPLD Firmware Update to REV07
  • UART Speed is 115200
  • Press XMOD Button to see output, otherwise RX/TX are loop backed
Scroll Title
anchorFigure_CPLD_FIRM
titleCPLD Firmware ID

Image Added


Scroll Title
anchorTable_CPLD_FIRM
titleCPLD Firmware and Statistic over UART

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

TypeDescription
TE0808-x_CPLD-REV07CPLD Firmware Version
MP
  • Main Power State, Note: Only correct, if 1.8V is powered on
  • First Number indicates 1.8V Power state(1-ON)
  • Second Number indicates Main State Machine:
    • 0:IDLE (Power OFF)
    • 1:ATX ON/OFF
    • 2:V5 ON/OFF
    • 3:Module Power ON/OFF → (Different domains over LED visible)
    • 4:1.8V ON/OFF
    • 5:Periphery ON/OFF
    • 6: Wait Ready (Power Ok, SoC on Reset)
    • 7. Ready (Power/SoC OK)
PIN
  • PS Init, when Power Reset released
  • First Number current PS-INIT (Inverted)
  • Second Number PSINIT counter
PEE
  • PS ERROR, when Power Reset released
  • First Number current PS-ERROR
  • Second Number ERROR counter
PES
  • PS ERROR Status, when Power Reset released
  • First Number current PS-ERROR Status
  • Second Number ERROR Status counter
PSR
  • PS Soft  Reset(also high, PS Power On Rese is active)
  • First Number current PS-Soft Reset
  • Second Number PS-Soft Reset counter
PHR
  • PS Power On Reset
  • First Number current PS- Power On Reset
  • Second Number PS- Power On Reset counter
POR
  • Main Power On Reset
  • First Number current Main- Power On Reset
  • Second Number Main Power On Reset counter
USB
  • USB Reset
  • First Number current USB Reset
  • Second Number USB reset counter
PCI
  • PCIe Reset
  • First Number current PCIe Reset
  • Second Number PCIe reset counter


Reference Designs

Page properties
hiddentrue
idComments

In this Section you must refer to the Reference Design (Test board) for the particular module.

For Example: TE0728 Reference Designs

Link to different Reference Designs (Descriptions and Download)


It's recommended to use prebuilt Boot.bin and image.ub of newest Starterkit Reference Design for first test. Basic Steps:

  1. Power Supply over ATX, optional 12V power jack
  2. Download Reference Design
  3. Copy Boot.bin and image.ub on SD 
  4. Connect USB to XMOD with Green Dot
  5. Open Putty
  6. Set Boot Mode to SD, set DIP S5-1 and S5-2 to ON (Overview 5) and inserted SD with Design on SD Slot (Overview R)
  7. Press Power Button on Enclosure or on Carrier (Overview 3)
  8. For more detailed check Reference Design description


Notes

Page properties
hiddentrue
idComments

In this Section you must refer to the Resources Page for the particular module.

For Example: TE0728 Resources

Module and Carrier are also as starter kit available:

Links to all documentation and download resources:





Scroll Only


HTML
<style>
.wiki-content .columnLayout .cell.aside {
width: 0%;
}</style>



Scroll pdf ignore


Custom_fix_page_content

Table of contents

Table of Contents
outlinetrue