Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Page properties
hiddentrue
idComments

Note:
Use 'Key Features' description in shoping page, for example: https://shop.trenz-electronic.de/de/TE0728-04-1Q-SoC-Micromodul-mit-Xilinx-Automotive-Zynq-7020-512-MByte-DDR3L-6-x-6-cm

  • Module: 
    • Trenz Electronic Module TE0745
    • Temperature: -40 to 85 °C
  • On Board:
    • 24V power supply terminal
    • 1 x EMI Network Filter
    • 3 x Variable Step Down Regulator Module (VDRM) with head sink
    • 2 x Synchronous Buck Regulator
    • 2 x Button (User / Reset)
    • 2 x LED (Green)
  • Interfaces:
    • 1 x XMOD (TE0790) Pin Header (JTAG / UART)
    • 1 x Pin Header (JTAG)
    • 1 x microSD connector
    • 1 x RJ45 Ethernet connector
    • 1 x USB Host Connector
    • 8 x SFP-Connector
    • 6 x Pin Header 50 pol. (FPGA Bank I/O's and Power)
    • 6 x Pin Header 12 pol. (FPGA Bank I/O's and Power)
    • 1 x battery holder
    • 2 x DIP Switch Array (VCC_HR_B / Modi)
  • Dimension: 200 mm x 231 mm

Block Diagram

...

Scroll Title
anchorTable_RH_HRH
titleHardware Revision History

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

201605-25
DateRevisionChangesDocumentation Link
2018-12-0602a
  • Resistors R14 and R15 was replaced by 953R (was 5K1)
  • Resistor R5 was replaced by 5K1, R8 by 953R (was 9K09 and 1K69 respectively)
REV02-A01-REV01
2018-10-1902
  • U16 I2C expander: address set to 0x72
  • U33 EEPROM: address set to 0x51. Added variant to set address 0x52.
  • Changed power up sequence: 24V_FUSED -> 3.3V (Module power up) -> 5V -> VCCIO18, VCC_HR_B, 3.3V_SFP
  • Fixed PCB patch: U6 pin 18 connected to 5V, pin 19 connected to GND.
  • JTAG connector J30 VREF (pin2) and XMOD VIO (pin 6) connected to 3.3V. XMOD IO A, B, E, G connected to module MIO via level translator U8.
  • Pull-up for BOOTMODE and PS_SW (DIP switch S1), RST_IN_N and USR_BTN (front panel buttons S2, S3) changed from VCCIO18 to PS_1.8V; JTAG_EN connected to 3.3V via DIP switch (S1).
  • Added switch S4 for selecting of output voltage of DCDC U7 (VCC_HR_B, HR banks VCCO)
REV02
20182016-1205-062502a
  • Resistors R14 and R15 was replaced by 953R (was 5K1)
  • Resistor R5 was replaced by 5K1, R8 by 953R (was 9K09 and 1K69 respectively)
01-REV01REV02-A




Document Change History

Page properties
hiddentrue
idComments
  • Note this list must be only updated, if the document is online on public doc!
  • It's semi automatically, so do following
    • Add new row below first

    • Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> this point is will be deleted on newer pdf export template

    • Metadata is only used of compatibility of older exports

...