Overview
The Trenz Electronic TEB0835 is a carrier for TE0835 module which is based on Xilinx UltraScale+ RFSoC. The Carrier is equipped with a Micro SD card reader, Micro USB2.0, 21x UMCC connectors and 6x SMD connectors for clocks and ADC/DAC inputs/outputs , 6x Green User LEDs, Reset Push Button, DIP Switch for Mode, Battery Holder, FT2232H FTDI, programmable clock generators and a Temperature sensor IC. The carrier provides PCIe connector as well.
Refer to http://trenz.org/teb0835-info for the current online version of this manual and other available documentation.
Key Features
Page properties |
---|
|
Note: 'description: Important components and connector or other Features of the module → please sort and indicate assembly options Key Features' must be split into 6 main groups for modules and mainboards: - SoC/FPGA
- Package: SFVC784
- Device: ZU2...ZU5*
- Engine: CG, EG, EV*
- Speed: -1LI, -2LE,*, **
- Temperature: I, E,*, **
- RAM/Storage
- Low Power DDR4 on PS
- Data width: 32bit
- Size: def. 2GB*
- Speed:***
- eMMC
- Data width: 8Bit
- size: def. 8GB *
- QSPI boot Flash in dual parallel mode (size depends on assembly version)
- Data width: 8bit
- size: def. 128MB *
- HyperRAM/Flash (optional, default not assembled)
- MAC address serial EEPROM with EUI-48™ node identity (Microchip 24AA025E48)
- On Board
- Lattice LCMXO2
- PLL SI5338
- Gigabit Ethernet transceiver PHY (Marvell Alaska 88E1512)
- Hi-speed USB2 ULPI transceiver with full OTG support (Microchip USB3320C)
- Interface
- 132 x HP PL I/Os (3 banks)
- ETH
- USB
- 4 GTR (for USB3, Sata, PCIe, DP)
- MIO for UART
- MIO for SD
- MIO for PJTAG
- JTAG
- Ctrl
- Power
- 3.3V-5V Main Input
- 3.3V Controller Input
- Variable Bank IO Power Input
- Dimension
- Notes
- * depends on assembly version
- ** also non low power assembly options possible
- *** depends on used U+ Zynq and DDR4 combination
Key Features' must be split into 6 main groups for carrier: - Modules
- TE0808, TE807, TE0803,...
- RAM/Storage
- On Board
- Interface
- E.g. ETH, USB, B2B, Display port
- Power
- E.g. Input supply voltage
- Dimension
|
Excerpt |
---|
- Modules:
- RAM/Storage
- On Board
- Programmable Clock Generator
- I2C Switch IC
- 6x User Green LEDs
- 16x RF Transformation
- Reset Push Button
- Temperature Sensor
- FT2232H FTDI
- SDIO Port Expander
- 2x DIP Switch
- Pin Headers
- PCIe 6 Connector
- Interface
- 21x UMCC Connectors
- 6x SMA Connectors
- 2x Micro USB2.0
- RJ45 LAN Socket
- Micro SD Card Socket
- 2x UEC5 Connectors
- 2x UCC8 Connectors
- PCIe x8 Card
- 2x Samtec Razor Beam SS5 (2x80 pol) Board to Board Connectors
- Power
- Dimension
|
Block Diagram
Page properties |
---|
|
add drawIO object here.
|
Scroll Title |
---|
anchor | Figure_OV_BD |
---|
title | TEB0835 block diagram |
---|
|
Scroll Ignore |
---|
draw.io Diagram |
---|
border | false |
---|
viewerToolbar | true |
---|
| |
---|
fitWindow | false |
---|
diagramDisplayName | |
---|
lbox | true |
---|
revision | 16 |
---|
diagramName | TEB0835_OV_BD |
---|
simpleViewer | false |
---|
width | 639 |
---|
links | auto |
---|
tbstyle | hidden |
---|
diagramWidth | 641 |
---|
|
|
Scroll Only |
---|
Image Modified |
|
Main Components
Page properties |
---|
|
Notes : - Picture of the PCB (top and bottom side) with labels of important components
- Add List below
|
Scroll Title |
---|
anchor | Figure_OV_MC |
---|
title | TEB0835 main components |
---|
|
Scroll Ignore |
---|
draw.io Diagram |
---|
border | false |
---|
viewerToolbar | true |
---|
| |
---|
fitWindow | false |
---|
diagramDisplayName | |
---|
lbox | true |
---|
revision | 15 |
---|
diagramName | TEB0835_OV_MC |
---|
simpleViewer | false |
---|
width | 639 |
---|
links | auto |
---|
tbstyle | hidden |
---|
diagramWidth | 642 |
---|
|
|
Scroll Only |
---|
Image Modified |
|
- SMA Connectors, J1,J3,J5,J7,J9,J11
- UMCC Connectors, J2,J4,J6,J8, J10, J12...16, J20, J27, J32...J38, J42...43
- Green LEDs, D6...11
- B2B Connector, J18
- B2B Connector, J17
- Micro SD Card Connector, J28
- Reset Push Button, BTN1
- PCIe 6 Pin Connector, J19
- Micro USB2.0 Connectors, J30
- Gigabit RJ45 Connector, J31
- DIP Switch, S1
- UEC5 Connector, J22,J24
- UCC8 Connector, J23,J25
- 1x4 Pin Header, J21
- FTDI, U12
- Green LEDs, D1...3
- 1x6 Pin Header, J40
- Micro USB2.0 Connectors (FTDI), J29
- PCIe-8x-kurz Card, J26
- Battery Holder, B1
- DIP Switch (PLL SEL), S2
- Pin Header (PLL I2C), J41
- Jumper (PWR CFG), J39
- EEPROM, U15
- RF Transformer, T2...17, T26...32
- Programmable Clock Generator, U5
Initial Delivery State
Page properties |
---|
|
Notes : Only components like EEPROM, QSPI flash can be initialized by default at manufacture. If there is no components which might have initial data ( possible on carrier) you must keep the table empty |
Scroll Title |
---|
anchor | Table_OV_IDS |
---|
title | Initial delivery state of programmable devices on the module |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Storage device name | Content | Notes |
---|
EEPROM | Programmed | FTDI Configuration |
|
Configuration Signals
Page properties |
---|
|
- Overview of Boot Mode, Reset, Enables.
|
Push Button BTN1 is provided to switch OFF all power supplies on RFSoC board.
Scroll Title |
---|
anchor | Table_OV_RST |
---|
title | Reset process. |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Signal | B2B | I/O | Note |
---|
RESETN | J17- 36 | Input | Connected to Push Button, BTN1 |
|
There is a DIP switch S1 provided for enabling CPLD and set the FPGA boot mode. The DIP Switch setting should be set like the following table.
Scroll Title |
---|
anchor | Table_OV_DIP |
---|
title | CPLD Configuration |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
DIP | Signal | Setting | Note |
---|
S1-A | CPLD_IO0 | FPGA boot config | Bit 0, CPLD Firmware dependent. | S1-B | CPLD_IO1 | FPGA boot config | SDA pin | S1-C | CPLD_IO2 | - | PROGRAMN pin | S1-D | CPLD_JTAGEN | CPLD JTAG EN | JTAGENB |
|
Boot Mode must be set using DIP Switch S1 on CPLD provided on the module TE0835. Please note that the DIP Switch is active low.
Scroll Title |
---|
anchor | Table_OV_BP |
---|
title | Boot process. |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
MODE Signal State | Boot Mode |
---|
S1-A | S1-B |
---|
JTAG | ON | ON | QSPI Flash | ON | OFF | SD Card | OFF | OFF |
|
Signals, Interfaces and Pins
Page properties |
---|
|
Notes : - For carrier or stand-alone boards use subsection for every connector type (add designator on description, not on the subsection title), for example:
- For modules which needs carrier use only classes and refer to B2B connector if more than one is used, for example
|
Board to Board (B2B) I/Os
Number of I/O signals and interfaces connected to the B2B connectors:
Scroll Title |
---|
anchor | Table_SIP_B2B |
---|
title | B2B connections information |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
B2B Connector | Interface | I/O Signal Count | Connected to | Notes |
---|
J17
| I2C | 3x Single Ended | I2C Switch, U7 |
| PLL Intrupt PLL Clocks | 1x Single Ended 4x Single Ended, 2x Differential pairs | PLL Clock Generator, U5 |
| JTAG | 4x Single Ended | FTDI, U12 |
| CPLD IO CPLD Enable | 3x Single Ended 1x Single Ended | DIP Switch, S1 |
| PCIe Reset | 1x Single Ended | PCIe Card, J26 |
| UART | 2x Single Ended | FTDI, U12 |
| Ethernet LED Ethernet MDI | 2x Single Ended 8x Single Ended | RJ45 Connector, J31 |
| SD Card | 6x Single Ended | Micro SD Memory Connector, J28 IO Expander, U11 |
| I/O | 16x Single Ended, 8x Differential pairs | PCIe Card, J26 | PCIe | I/O | 16x Single Ended, 8x Differential pairs | UEC5 Connector, J22 | UEC5 | I/O | 16x Single Ended, 8x Differential pairs | UEC5 Connector, J24 | UEC5 | Micro USB2.0 | 2x Single Ended 1x Single Ended 2x Single Ended | Micro USB2.0 Connector, J30 Voltage Regulator, U17 Diode, D5 |
| J18 | ADC | 16x Single Ended, 8x Differential pairs | SMA, J1, J3, J5, J7 UMCC, J2, J4, J6, J8 |
| ADC Clock | 4x Single Ended, 2x Differential pairs | UMCC, J27, J32 |
| DAC | 16x Single Ended, 8x Differential pairs
| SMA, J9, J11 UMCC, J10, J12, J13...16 |
| DAC Clock | 4x Single Ended, 2x Differential pairs | UMCC, J33, J34 |
| Green LEDs | 6x Single Ended, 3x Differential pairs | Green LEDs, D6...11 |
| I/O | 10x Single Ended | UCC8 Connector, J23, J25 | UCC8 |
|
Gigabit Ethernet
Scroll Title |
---|
anchor | Table_SIP_ETH |
---|
title | Gigabit Ethernet information |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Signal Name | Connected to | Signal Description | Note |
---|
PHY_MDI0...3 | B2B, J17 | Media Data |
| PHY_LED0...1 | B2B, J17 | Speed/Link Indicators LED | Yellow/Green |
|
Micro USB for JTAG/UART
The TEB0835 is equipped with two Micro USB2.0 Connectors J29, J30. The Micro USB2.0 port, J29 is provided for JTAG/UART and it is connected to FTDI, U12.
Scroll Title |
---|
anchor | Table_SIP_MUSB2 |
---|
title | Micro USB2 to JTAG/UART connections |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J29 | D_N/D_P | FTDI,U12 | Data | USB_VBUS | Diode, D4 | VBUS |
|
Micro USB2.0
There is a Micro USB2.0 J30, provided for user.
Scroll Title |
---|
anchor | Table_SIP_MicroUSB2 |
---|
title | Micro USB2.0 Socket connections |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J30
| USB_N/USB_P | B2B, J17 | Data | USB0_VBUS | B2B, J17 | VBUS | USB0_ID | B2B, J17 | ID |
|
Micro SD Card Reader
There is a Micro SD Card socket J28 connected to B2B J17 through an I/O expander U11.
Scroll Title |
---|
anchor | Table_SIP_MicroSD |
---|
title | Micro SD Card Socket connections |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Pin | Signal Name | Connected to | Note |
---|
VDD | 3.3V_SD | B2B, J17 | connected to IO expander | CMD | SD_CMD | B2B, J17 | connected to IO expander | CLK | SD_CLK | B2B, J17 | connected to IO expander | DATA0...3 | SD_DATA0...3 | B2B, J17 | connected to IO expander | CD | SD_CD | B2B, J17 |
|
|
SMA Connectors
There are 6 SMA Connectors provided for Analog and Digital signals.
Scroll Title |
---|
anchor | Table_SIP_SMA |
---|
title | SMA Connectors information |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J1 | ADC0_IN | B2B, J18 | Via RF Transformer T2 | J3 | ADC2_IN | B2B, J18 | Via RF Transformer T6 | J5 | ADC4_IN | B2B, J18 | Via RF Transformer T4 | J7 | ADC6_IN | B2B, J18 | Via RF Transformer T8 | J9 | DAC0_OUT | B2B, J18 | Via RF Transformer T10 | J11 | DAC2_OUT | B2B, J18 | Via RF Transformer T12 |
|
UMCC Connectors
There are 21x UMCC Connectors provided for Analog /Digital signals and Clocks input and output.
Scroll Title |
---|
anchor | Table_SIP_UMCC |
---|
title | UMCC Connectors |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J2 | ADC1_IN | B2B, J18 | Via RF Transformer T3 | J4 | ADC3_IN | B2B, J18 | Via RF Transformer T5 | J6 | ADC5_IN | B2B, J18 | Via RF Transformer T7 | J8 | ADC7_IN | B2B, J18 | Via RF Transformer T9 | J10 | DAC1_OUT | B2B, J18 | Via RF Transformer T11 | J12 | DAC3_OUT | B2B, J18 | Via RF Transformer T13 | J13 | DAC4_OUT | B2B, J18 | Via RF Transformer T14 | J14 | DAC5_OUT | B2B, J18 | Via RF Transformer T15 | J15 | DAC6_OUT | B2B, J18 | Via RF Transformer T16 | J16 | DAC7_OUT | B2B, J18 | Via RF Transformer T17 | J27 | ADC_CLK_224 | B2B, J18 | Via RF Transformer T26 | J20 | ADC_CLK_225 | B2B, J18 | Via RF Transformer T27 | J32 | ADC_CLK_226 | B2B, J18 | Via RF Transformer T28 | J33 | ADC_CLK_227 | B2B, J18 | Via RF Transformer T29 | J34 | DAC_CLK_228 | B2B, J18 | Via RF Transformer T30 | J35 | DAC_CLK_229 | B2B, J18 | Via RF Transformer T31 | J36 | CLKIN1 | Programmable Clock Generator, U5 |
| J37 | CLKIN2 | Programmable Clock Generator, U5 |
| J38 | CLKOUT7 | Programmable Clock Generator, U5 | Via RF Transformer T32 | J42 | CLKOUT8 | Programmable Clock Generator, U5 |
| J43 | CLKOUT9 | Programmable Clock Generator, U5 |
|
|
UCE5 Connectors
The TEB0835 is equipped with two UCE5 Connectors.
Scroll Title |
---|
anchor | Table_SIP_UEC5 |
---|
title | UEC5 Connectors |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J22 | B128_TX0...3 | B2B, J17 | 8x Single Ended/ 4x LVDS Pairs | B128_RX0...3 | B2B, J17 | 8x Single Ended/ 4x LVDS Pairs | J24 | B129_TX0...3 | B2B, J17 | 8x Single Ended/ 4x LVDS Pairs | B129_RX0...3 | B2B, J17 | 8x Single Ended/ 4x LVDS Pairs |
|
UCC8 Connectors
The TEB0835 is equipped with two UCC8 Connectors.
Scroll Title |
---|
anchor | Table_SIP_UCC8 |
---|
title | UCC8 Connectors |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Designator | Signal Name | Connected to | Note |
---|
J23 | FFA_MPRS | B2B, J17 |
| FFA_MSEL | B2B, J17 |
| FFA_INTL | B2B, J17 |
| FFA_RSTL | B2B, J17 |
| FFA_SCL/FFA_SDA | I2C Switch, U7 |
| J25 | FFB_MPRS | B2B, J17 |
| FFB_MSEL | B2B, J17 |
| FFB_INTL | B2B, J17 |
| FFB_RSTL | B2B, J17 |
| FFB_SCL/FFB_SDA | I2C Switch, U7 |
|
|
PCIe 8x