- Created by Mohsen Chamanbaz, last modified on 03 04, 2024
You are viewing an old version of this page. View the current version.
Compare with Current View Page History
« Previous Version 3 Next »
TEB2000 with TEM0007
Overview
Board Overview
Number | Note |
---|---|
1 | J14- Ethernet interface |
2 | J5,J8,J9,J10- Bank voltage adjustment |
3 | JB1,JB2,JB3- B2B connector |
4 | J3- SD card socket |
5 | J21- UART0 socket |
6 | J4- UART1 socket |
7 | J13- 5V voltage input |
8 | J12- USB stick socket |
9 | S6- Reset button (SRST) (Soft reset) |
10 | S1- Reset button ( Hard reset) |
11 | S2- Dip Switch |
12 | U4- CPLD Chip |
Power supply
Single 5V power supply with minimum current capability of 1.5A is recommended to power on the board.
DIP-Switches and Push Buttons
There is two switch (S1 and S6) which is connected to RESET signals, these reset the system entirely. The S6 is a soft reset buttom and S1 create a reset signal via hardware.
Signal | Designator | Connected to | Active Level | Description |
---|---|---|---|---|
SRST | S6 | B2B JB2 pin 56 | Active low | |
S1 | S1 | CPLD chip pin 114 | Active low |
Dip Switch S2 | Signal | Position ON | Position OFF | Connected to | Description |
---|---|---|---|---|---|
S2-1 | MIO0 | MODE pin ( B2B JB1 pin 31 set to '0') | MODE pin ( B2B JB1 pin 31 set to '1') | CPLD Chip pin 94 / B2B JB1 pin 88 | |
S2-2 | JTAGEN | Module FPGA JTAG access ( if S2-3 ON) | Module CPLD JTAG access (if S2-3 ON) | CPLD chip pin 120 | |
S2-3 | CM0 | Module FPGA/CPLD JTAG access (depends on S2-3) | Carrier CPLD JTAG access | CPLD chip pin 76 | |
S2-4 | CM1 | PGOOD signal set to '0' | PGOOD signal set to '1' | CPLD chip pin 75 |
There is no DIPs on TEM0007 module.
Jumpers
Designator | Connected to | Default set to | Note |
---|---|---|---|
J5 | VCCIOA | M1.8VOUT | It can be set to both 1.8V or 3.3V for TEM0007 module. |
J8 | VCCIOB | M1.8VOUT | May be set to either 3.3V or 1.8V. If set to 1.8V --> VDDAUX1 (TP5) = 2.5V±3% |
J9 | VCCIOC | M1.8VOUT | It can be set to both 1.8V or 3.3V for TEM0007 module. |
J10 | VCCIOD | M1.8VOUT | Important note: Only set to 1.8V for TEM0007 module. |
LEDs
There are three user LEDs which can be used for variant purposes.
Designator | Color | Connected to | B2B | Active Level | Note |
---|---|---|---|---|---|
Designator | Color | Connected to | Active Level | Note |
---|---|---|---|---|
Designator | Color | Connected to | Active Level | Note |
---|---|---|---|---|
JTAG/UART
JTAG and UART connections are available through mini USB connector.
Designator | Connected to | B2B Pin | XMOD Header JB? | Direction | Note |
---|---|---|---|---|---|
Reference Designs
Notes
Table of contents
- No labels