| Company | Trenz Electronic GmbH |
|---|---|
| PCN Number | PCN-20240618 |
| Title | TE0841-02 to TE0841-03 Hardware Revision Change |
| Subject | Hardware Revision Change |
| Issue Date | 2024-06-18 |
Products Affected
This change affects all Trenz Electronic TE0841-02 SoMs: TE0841-02*.
Affected Product | Replacement |
|---|---|
| TE0841-02-31C21-A | TE0841-03-31C31-A |
| TE0841-02-31C31-A | TE0841-03-31C31-A |
| TE0841-02-31I21-A | TE0841-03-31I31-A |
| TE0841-02-31I21-T | TE0841-03-31I31-T |
| TE0841-02-32I21-A | TE0841-03-32I31-A |
| TE0841-02-41C21-A | TE0841-03-41C31-A |
| TE0841-02-41I21-A | TE0841-03-41I31-A |
| TE0841-02-41I21-L | TE0841-03-41I31-L |
ED: Tabelle ist fertig!
Changes
#1 Changed DCDC EN63A0QI (U7, U14) to LTM4638EY#PBF
Type: Schematic change
Reason: EOL of component.
Impact: None. Maximum continuous output current increased from 12A to 15A per DCDC.
#2 Increased voltage from 1.35 V to 1.42 V via voltage divider resistor (R11) and changed voltage rail name accordingly from PL_GT_1V35 to PL_GT_1V42.
Type: Schematic Change
Reason: Improve voltage rail behaviour.
Impact: None.
#3 Changed load switch TPS27082LDDCR (Q1) to MP5077GG-Z and adapted circuit.
Type: Schematic Change
Reason: BOM Optimization.
Impact: None. Minor changes in electrical characteristics.
#4 Changed clock (U11) from DSC1123DL5-200.0000 to SIT9121AI-2B1-XXE-200.00000.
Type: Schematic Change
Reason: BOM Optimization.
Impact: Decreased stability from ± 10 ppm to ± 20 ppm. Decreased temperature range from (-40 °C to 105 °C) to (-40 °C to 85 °C). Increased mechanical size.
#5 Added power supervisor STM6710LWB6F (U21) and connected it to system controller (U18) pin 5 via net "PG_ALL" which is pulled-up to power rail "3.3VIN" with resistor (R83).
Type: Schematic Change
Reason: Improve power monitoring.
Impact: Improved power monitoring circuit by supervising additional voltage rails. If monitored voltages are out of range signal "PG_ALL" is triggered.
#6 Added diode (D2) between signals "INIT_B" and "PROG_B".
Type: Schematic Change
Reason: Keep FPGA in reset while signal "PROG_B" is low during initial power-up.
Impact: None.
#7 Added pull-up resistor (R79, R80, R81, R82) for signals "PROG_B", "INIT_B", "DONE", "PG_GT".
Type: Schematic Change
Reason: Use external pull-up resistor.
Impact: None.
#8 Added additional decoupling capacitor (C70 ... C84, C89).
Type: Schematic Change
Reason: Improve power supply.
Impact: None.
#9 Changed ferrid bead (L1 ... L6) from BKP0603HS121-T to MPZ0603S121HT000.
Type: BOM Change
Reason: EOL of component.
Impact: None.
#10 Changed capacitor (C49) from 4.7 µF, 6.3 V, 0402 to 10 µF 16 V, 0603.
Type: Schematic Change
Reason: Increase voltage rating.
Impact: None.
#11 Changed resistor (R35) from 4.7 kOhm 50 mW, 0201 to 2.37 kOhm 63 mW, 0402.
Type: Schematic Change
Reason: Follow AMD recommendation.
Impact: None.
#12 Changed resistor (R25, R26, R52, R57) from 4.7 kOhm 50 mW, 0201 to 23.7 kOhm 63 mW, 0402.
Type: Schematic Change
Reason: Decrease current flow through resistor.
Impact: None.
#13 Set resistor (R71) to not fitted.
Type: Schematic Change
Reason: BOM Optimization.
Impact: None.
#14 Added testpoint (TP3 ... TP37).
Type: Schematic Change
Reason: Power and signal monitoring improvement.
Impact: None.
#15 Swapped clock (U11) net name "CLK200M_P" and "CLK200M_N" at pin 4 and 5.
Type: Schematic Change
Reason: Documentation improvement.
Impact: None.
#16 Updated components from library.
Type: Schematic Change
Reason: Use latest component data.
Impact: None.
#17 Signal trace lengths changed
Type: PCB change
Reason: Result of changes above.
Impact: Changed trace length have to be taken into account in existing designs. The trace length for new revision will be available in TE0841 series pinout generator. Please check if change in trace length still matches your requirements. Adaption of carrier may be necessary.
#18 Added legal notices, system and power diagram. Updated revision history. Updated page count and order.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.
Method of Identification
Production Shipment Schedule
From XXXXX, after old stock is gone. If the new revision is not suitable for your application and still the former revision of the board is needed, please contact us.
Contact Information
If you have any questions related to this PCN, please contact Trenz Electronics Technical Support at
- forum.trenz-electronic.de
- wiki.trenz-electronic.de
- support%trenz-electronic.de (subject = PCN-20240618)
phone
national calls: 05741 3200-0
international calls: 0049 5741 3200-0
Disclaimer
Any projected dates in this PCN are based on the most current product information at the time this PCN is being issued, but they may change due to unforeseen circumstances. For the latest schedule and any other information, please contact your local Trenz Electronic sales office, technical support or local distributor.
This PCN follows JEDEC Standard J-STD-046.
Overview
Content Tools