You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 21 Next »

 

Download PDF version of this document.

Overview

The Trenz Electronic TEB2000 carrier board provides functionality for development, evaluation and testing purposes of Trenz 4 x 5 cm SoMs (System on Module).

The carrier board is equipped with a broad range of various components and connectors for different configuration setups and needs. On-module functional components and multipurpose I/Os of the SoM's PL and PS logic are connected via board-to-board connectors to the carrier board components and connectors for easy user access.

See page "4 x 5 SoM Carriers" for more information about the SoM's supported by the TEB2000 Carrier Board.

Refer to http://trenz.org/teb2000-info for the latest online version of this manual and other available documentation.

Key Features

  • On Board:
    • System Controller (SC) (LCMXO2-1200HC-4TG144I1))
    • Mini USB for JTAG and UART connection (FTDI FT2232H)
    • Mini USB second UART connection (FTDI FT230XQ)
    • SDIO port expander
    • 4 x User LEDs
      • D1, D2 connected to SC (firmware-dependent functionality)
      • D3, D4 connected to SC and 4 x 5 SoM
    • 2 x User push button
      • Connected to SC (firmware-dependent functionality)
      • Currently used for Hard- and Soft-Reset
    • 4 User DIP switches
      • Enable/disable update of the SC
      • MIO0 (accessible signal by SC and SoM)
      • 2 "mode" bits
  • Interface:
    • Trenz 4 x 5 SoM socket
      • 3 x Samtec LSHM series high-speed connectors
    • Micro SD card connector
    • 2 x VG96 backplane connectors assembly option (mounting holes and solder pads)
    • Mini or Normal USB for SoM USB-OTG connection 1)
    • RJ45 GbE connector
  • Power:
    • Overvoltage-, undervoltage- and reversed- supply-voltage-protection
    • Barrel jack (2.1 mm) for 5V power supply input
  • Dimension:
    • 100 mm x 64.5 mm
  • Notes

1) Depends on assembly variant

Block Diagram

TEB2000 block diagram

Main Components

TEB2000 main components
  1. System Controller (SC), U5
  2. USB-to-JTAG/UART-FTDI, U4, U12
  3. UART Level Shifter, U8
  4. SDIO Port Expander, U2
  5. I²C Repeater, U7
  6. Power Input Protection, U11
  7. DCDC, U3
  8. USB Power Supply Switch, U1
  9. Reset / Push button, S1, S6
  10. 4x Dip Switch, S2
  11. LED D1 (red), D2 (green)
  12. LED D3 (red), D4 (green)
  13. Ethernet Jack, J14
  14. Samtec Razor Beam™ LSHM-150/130 B2B connector, JB1, JB2, JB3
  15. Assembly option for VG96 Connector, J1, J2
  16. Power Jack, J13
  17. microSD Card Socket, J3
  18. Bank IO Voltages jumper, J5, J8, J9, J10
  19. Mini USB Type B Jack, J4 (FT2232H), J21 (FT230XQ)
  20. USB Host Connector, J6 (USB A) or J12 (Micro USB)

Initial Delivery State

Storage device name

Content

Notes

EEPROMPreprogrammed with Microchip programmer license

Do not overwrite!

System ControllerPreprogrammed with FirmwareVisit TEB2000 Firmware for further information.
Initial delivery state of programmable devices on the module

Signals, Interfaces and Pins

Connectors

Connector TypeDesignator

InterfaceIO CNTNotes
VG96J1JB1 - IO

48 SE / 24 DIFF


RJ-45 Ethernet
J14Ethernet8
RJ-45 EthernetJ14U5 - ETH LED4
VG96J2JB2 - IO65 SE / 32 DIFF
VG96J1JB3 - IO36 SE / 18 DIFF
USB Type A 1)J6JB3 - USB 2.0 OTG2

Micro USB Type A/B 1)

J12JB3 - USB 2.0 OTG2
VG96J2SC - IO16
B2BJB2SC - JTAG4
B2BJB2SC - Reset1
Mini USB Type BJ4SC - USB 2.02
Mini USB Type BJ21SC - USB 2.02
B2BJB1SC - UART2
B2BJB1SC - UART2
B2B 2)JB1SD6
microSD Card socket 2)J3SD6
VG96J1SC - I²C2
VG96J1JB1 - I²C2

1) Depending on the variant only one of the USB connectors is assembled.
2) Depending on firmware microSD Card socket is connected to SC or SoM. Refer to TEB2000 CPLD Firmware for further information.

Board Connectors


Test Points

Test PointSignalDirection 1)Notes
TP15VININ
TP25VININ
TP3VININ
TP4VININ
TP53.3VOUT
TP63.3VOUT
TP7VCCIOAIN
TP8VCCIOAIN
TP9VCCIOBIN
TP10VCCIOBIN
TP11VCCIOCIN
TP12VCCIOCIN
TP13VCCIODIN
TP14VCCIODIN
TP15M1.8VOUTIN
TP16M1.8VOUTIN
TP17M3.3VOUTIN
TP18M3.3VOUTIN
TP19UART_VBUSIN
TP20UART_VBUSIN
TP21VCCJTAGIN
TP22VCCJTAGIN
TP233.3V_SDOUT
TP243.3V_SDOUT
TP25USB-VBUS_ROUT
TP26USB-VBUS_ROUT
TP27ETH-VCCIN
TP28ETH-VCCIN
TP29VbusIN
TP30VbusIN
TP31CM1IN
TP32CM0IN
TP33MIO0IN
TP34JTAGENIN

1) Direction:

    • IN: Input from the point of view of this board.
    • OUT: Output from the point of view of this board.
Test Points Information

On-board Peripherals

Chip/InterfaceDesignatorConnected ToNotes

System Controller

U5
  • SoM
  • FTDI (FT2232H)
  • FTDI (FT230XQ)
  • SD Port Expander
  • Push button S1
  • Push button S6
  • DIP Switch S2
  • All LEDs
Visit TEB2000 CPLD Firmware for further information.

FTDI FT2232H

U4
  • SC
  • J4
UART for Application

EEPROM

U10
  • FTDI

Preprogrammed with AMD programmer license.

Do not overwrite!

FTDI FT230XQ

U12
  • SC
  • J21

UART for HSS/System Boot

Oscillator

U6
  • U4 FTDI

12 MHz

SD IO Port Expander

U2
  • SC
  • Via JB1 B2B connector to SoM
  • microSD Card J3

On board peripherals

Configuration and System Control Signals

Signal Name

Connector.Pin

Direction1)Description
S1S1.2 / S1.4IN

Push button 2)

SRSTS6.2 / S6.4IN

Push button.

CM1S2.8IN

DIP Switch 2)

CM0S2.7IN

DIP Switch 2)

JTAGENS2.6IN

DIP Switch 2)

MIO0S2.5IN

DIP Switch 2)

VCCIOAJ5.2OUTSoM IO Bank supply 3)
VCCIOBJ8.2OUTSoM IO Bank supply 3)
VCCIOCJ9.2OUTSoM IO Bank supply 3)
VCCIODJ10.2OUTSoM IO Bank supply 3)
SD_CDJ3.9INSD Card socket Detect Signal
VBUS_V_ENJB3.54INEnables USB Host Bus Voltage
USB-VBUSJB3.56OUTSignal to SoM
RESINJB2.17OUTReset signal
EN1JB1.27OUTPower enable signal
PGOODJB1.29INOUTPower good and/or Boot mode select signal 2)
MODEJB1.31INOUTBoot mode select signal 2)
NOSEQJB1.8INOUT

Power Management and/or Select JTAG target on the SoM 2)

PROGMODEJB1.90INOUTSelect JTAG target on the SoM 2)
MIO14 / MIO15JB1.91 / JB1.86INOUTUART to SoM (FT2230H) 2)
MIO12 / MIO13JB1.100 / 98INOUTUART to SoM (FT230XQ) 2)
MIO10-SCL / MIO10
MIO10-SDA / MIO11
J1A.A1 / J1A.A2INOUTI2C bus 2)

1) Direction:

    • IN: Input from the point of view of this board.
    • OUT: Output from the point of view of this board.

2) Firmware dependent. Refer to TE0703 CPLD - CC703S for further information.
3) Select 1.8V or 3.3V via jumper. Refer to 4 x 5 Module Integration Guide for further information.

Controller signal.

Power and Power-On Sequence


Power Rails

Power Rail Name/ Schematic NameConnector.PinDirection1)Notes
5VIN J13.1IN
5VIN J2A.A1 / J2A.A2OUT
3.3VJ1C.C31 / J2C.C31 /
JB1.2 /  JB1.4/  JB1.6/  JB1.14/  JB1.16 /
JB2.1 / JB2.3 / JB2.5 / JB2.7
OUT
USB-VBUSJ6.1 / J12.1 / JB3.56OUT

M1.8VOUT

JB1.40IN

M1.8VOUT

J5.3 / J8.3 / J9.3 / J10.3OUT

M3.3VOUT

JB2.9 / JB2.11IN

M3.3VOUT

J5.1 / J8.1 / J9.1 / J10.1 /
J1C.C32 / J2C.C32
OUT

VCCJTAG

JB2.92IN

ETH-VCC

JB1.13IN
VCCIOAJB1.10 / JB1.12 / J1B.B1OUT

Selection via J5 2)

VCCIOB

JB2.2 / JB2.4 / J1B.B32

OUT

Selection via J8 2) 

VCCIOCJB2.6 / J2B.B32
OUT

Selection via J9 2)

VCCIODJB2.8 / JB2.10 / J2B.B1OUT

Selection via J10 2)

1) Direction:

    • IN: Input from the point of view of this board.
    • OUT: Output from the point of view of this board.

2) Select 1.8V or 3.3V via jumper. Refer to 4 x 5 Module Integration Guide for further information.

Module power rails.

Recommended Power up Sequencing


SequenceNet nameRecommended Voltage RangePull-up/down

Description

Notes
0---Configuration signal setup.See Configuration and System Control Signals.
15VIN5V (± 5 %)-Main Power supply.

Carrier and SoM power supply.
Minimal 1 A, maximal 4A. 

Power consumption depends mainly on design and cooling solution.

2M3.3VOUT / M1.8VOUT3.3 V (± 3 %) / 1.8 V (± 3 %)-

SoM generated voltage, 
which signals operational readyness of the SoM.


3---Apply voltages to Carrier powered external IO 
when voltages under point 2 are present.

Baseboard Design Hints

Board to Board Connectors

These connectors are hermaphroditic. Odd pin numbers on the module are connected to even pin numbers on the baseboard and vice versa.

4 x 5 modules use two or three Samtec Razor Beam LSHM connectors on the bottom side.

  • 2 x REF-189016-02 (compatible to LSHM-150-04.0-L-DV-A-S-K-TR), (100 pins, "50" per row)
  • 1 x REF-189017-02 (compatible to LSHM-130-04.0-L-DV-A-S-K-TR), (60 pins, "30" per row) (depending on module)
Connector Mating height

When using the same type on baseboard, the mating height is 8mm. Other mating heights are possible by using connectors with a different height

Order numberConnector on baseboardcompatible toMating height
23836REF-189016-01LSHM-150-02.5-L-DV-A-S-K-TR6.5 mm

LSHM-150-03.0-L-DV-A-S-K-TRLSHM-150-03.0-L-DV-A-S-K-TR7.0 mm
23838REF-189016-02LSHM-150-04.0-L-DV-A-S-K-TR8.0 mm

LSHM-150-06.0-L-DV-A-S-K-TRLSHM-150-06.0-L-DV-A-S-K-TR10.0mm
26125REF-189017-01LSHM-130-02.5-L-DV-A-S-K-TR6.5 mm

LSHM-130-03.0-L-DV-A-S-K-TRLSHM-130-03.0-L-DV-A-S-K-TR7.0 mm
24903 REF-189017-02LSHM-130-04.0-L-DV-A-S-K-TR8.0 mm

LSHM-130-06.0-L-DV-A-S-K-TRLSHM-130-06.0-L-DV-A-S-K-TR10.0mm
Connectors.

The module can be manufactured using other connectors upon request.

Connector Speed Ratings

The LSHM connector speed rating depends on the stacking height; please see the following table:

Stacking heightSpeed rating
12 mm, Single-Ended7.5 GHz / 15 Gbps
12 mm, Differential

6.5 GHz / 13 Gbps

5 mm, Single-Ended11.5 GHz / 23 Gbps
5 mm, Differential7.0 GHz / 14 Gbps
Speed rating.
Current Rating

Current rating of  Samtec Razor Beam™ LSHM B2B connectors is 2.0A per pin (2 adjacent pins powered).

Connector Mechanical Ratings
  • Shock: 100G, 6 ms Sine
  • Vibration: 7.5G random, 2 hours per axis, 3 axes total


Manufacturer Documentation

  File Modified
PDF File hsc-report_lshm-lshm-05mm_web.pdf High speed test report 07 04, 2016 by Thorsten Trenz
PDF File lshm_dv.pdf LSHM catalog page 07 04, 2016 by Thorsten Trenz
PDF File LSHM-1XX-XX.X-X-DV-A-X-X-TR-FOOTPRINT(1).pdf Recommended layout and stencil drawing 07 04, 2016 by Thorsten Trenz
PDF File LSHM-1XX-XX.X-XX-DV-A-X-X-TR-MKT.pdf Technical drawing 07 04, 2016 by Thorsten Trenz
PDF File REF-189016-01.pdf Technical Drawing 07 04, 2016 by Thorsten Trenz
PDF File REF-189016-02.pdf Technical Drawing 07 04, 2016 by Thorsten Trenz
PDF File REF-189017-01.pdf Technical Drawing 07 04, 2016 by Thorsten Trenz
PDF File REF-189017-02.pdf Technical Drawing 07 04, 2016 by Thorsten Trenz
PDF File TC0923--2523_report_Rev_2_qua.pdf Design qualification test report 07 04, 2016 by Thorsten Trenz
PDF File tc0929--2611_qua(1).pdf Shock and vibration report 07 04, 2016 by Thorsten Trenz



Technical Specifications


Absolute Maximum Ratings *)

Power Rail / Schematic NameDescriptionMinMaxUnit
5VIN

Main input power supply

-0.360V
VCCIOA 1) 2)

Module power supply.

--V
VCCIOB 1) 2)Module power supply.--V
VCCIOC 1) 2)

Module and Carrier power supply.

-0.53.75V
VCCIOD 1) 2)Module power supply.--V
M1.8VOUT

Module and carrier power supply.

-0.31.95V
M3.3VOUT

Module and carrier power supply.

-0.3

3.6

V
VBAT 1)Module battery power supply.--V
VCCJTAG

JTAG Reference Voltage

-0.53.75V
ETH-VCCPower supply for ETH connection.--V

1) Module-dependent.
2) Voltage is intended to be supplied by M1.8VOUT or M3.3VOUT but can also be supplied externally via VG96 connection.

Absolute maximum ratings

*) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Condition. Exposure to absolute-maximum rated conditions for extended periods may affect device reliability.


Recommended Operating Conditions

This TRM is generic for all variants. Temperature range can differ depending on assembly variant. The voltage ranges between variants should not be affected (exceptions are possible, depending on custom request)

Temperature Range:

This carrier board is capable of being operated at industrial-grade temperatures, which cover at least the range of -40 °C to 85 °C.

Please check the operating temperature range of the mounted SoM and peripheral devices, which determines the operating temperature range of the overall system.

The Operating temperature range depends on soft- & hard- ware design and cooling solution. Please contact us for options.

Voltage Rails:


Power Rail / Schematic NameDescriptionMinMaxUnitNotes
5VIN

Main input power supply

4.755.25V
VCCIOA 1) 2)

Module power supply.

-

-

V


VCCIOB 1) 2)Module power supply.--V
VCCIOC 1) 2)

Module and Carrier power supply.

1.14

3.6

V


VCCIOD 1) 2)Module power supply.--V
M1.8VOUT

Module and carrier power supply.

1.7461.854V
M3.3VOUT

Module and carrier power supply.

3.2013.399V
VBAT 1)Module battery power supply.--V

VCCJTAG

JTAG Reference Voltage

1.143.6V
ETH-VCCPower supply for ETH connection.--V
Recommended operating conditions.

Physical Dimensions

  • Carrier size: 100 mm x 64.5 mm. 
    Note that few parts are slightly hanging over the PCB edge. Please download the assembly diagram for exact numbers.

  • Mating height with standard connectors: 8 mm. 

    PCB thickness: 1.64  mm ± 10 %.

Physical Dimension

Currently Offered Variants 

Trenz shop TEB2000 overview page
English pageGerman page
Trenz Electronic Shop Overview

Revision History

Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Board hardware revision number.


DateRevisionChangesPCN LinkDocumentation Link
2023-10-01Initial Revision


Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Document Change History

DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3575#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3575#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3575#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • <add TRM change list here>


01



--

all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3575#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3575#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]


Table of contents



  • No labels