You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 9 Next »

Table of Contents

Overview

 

The Trenz Electronic TE0722-02 is a DIPFORTy1 "Soft Propeller" based on the Xilinx ZYNQ-7000 SoC.

Block Diagram

Main Components

  1. Xilinx ZYNQ XC7Z010 SoC, U1
  2. Micro SD card socket with card detect, J8
  3. Red LED, D3
  4. Green LED, D2
  5. Red LED, D6
  6. 20-pin connector placeholder, P1
  7. Red LED, D5
  8. Proximity/ambient light sensor, U4
  9. RGB LED, D4
  10. Red LED, D1
  11. 20-pin connector placeholder, P2
  12. Ultra-low supply-current voltage monitor, U4
  13. 2 x 5-pin connector placeholder, J1
  14. 2 x 5-pin connector placeholder, J2
  15. 2 x 5-pin connector placeholder, J3
  16. 16 MByte QSPI Flash memory, U5
  17. Low power programmable oscillator @ 33.333333 MHz, U8
  18. 1A PowerSoC DC-DC converter (1.0V), U2
  19. 1A PowerSoC DC-DC converter (1.8V), U3

Key Features

  • Xilinx ZYNQ XC7Z010 SoC
  • 16 MByte QSPI Flash
  • Dual core ARM A9+
  • Micro SD Card socket with card detect signal
  • DIP40 form factor (size 18 x 51 mm)
  • 34 I/Os on DIP40 header pins
  • System status LED (DONE)
  • RGB LED connected to PL I/O
  • Green user LED connected to ARM CPU GPIO
  • Proximity and ambient light sensor

Additional assembly options are available for cost or performance optimization upon request.

Initial Delivery State

Storage device name

Content

Notes

QSPI Flash

Empty

 

Signals, Interfaces and Pins

I/O Signals

List of signals between PL banks and external connectors:

BankTypeConnectorI/O Signal CountVoltageNotes
34HRP183.3P0 - P7
34HRP283.3P24 - P31
34HRP210, 5 LVDS pairs3.3 
34HRJ163.3X2A - X2F
34HRJ223.3 
34HRJ343.3X1A - X1D
35HRP18, 4 LVDS pairs3.3 

JTAG Interface

JTAG access to the Xilinx ZYNQ XC7Z010 SoC is provided through J2 connector.

JTAG Signal

J2 Connector Pin

TCK 4
TDI 9
TDO 10
TMS 8

LEDs

LEDColorConnected ToDescription and Notes
D1RedLED2, U4 
D2

Green

MIO7, U1User controlled, default OFF (when PS7 has not been booted).
D3

Red

LED1, U4

 
D4RGB

RGB_R, U1

RGB_G, U1

RGB_B, U1

 
D5RedLED3, U4 

D6

Green

DONE, U1

Reflects inverted DONE signal. ON when FPGA is not configured,

OFF as soon as PL is configured.

Default PS MIO Mapping

MIOFunctionConnector PinNotes
0---
1QSPI-SPI Flash-CS
2QSPI-SPI Flash-DQ0
3QSPI-SPI Flash-DQ1
4QSPI-SPI Flash-DQ2
5QSPI-SPI Flash-DQ3
6QSPI-SPI Flash-SCK
7GPIO-Green LED D2
8---
9---
28SD CARDJ8-5CLK
29SD CARDJ8-3CMD
30SD CARDJ8-7DAT0
31SD CARDJ8-8DAT1
32SD CARDJ8-1DAT2
33SD CARDJ8-3CD/DAT3
36I2C-SCL
37I2C-SDA
39GPIO-Si1143 INT pin
49SD CARDJ8-G4Card detect switch

I2C Interface

On-board I2C interface is provided via ZYNQ SoC PS bank 501 pins MIO36 (SCL) and MIO37 (SDA). I2C addresses for on-board devices are listed in the table below:

I2C DeviceI2C AddressNotes
 Si1143-A11-GMR0x5AProximity and ambient light sensor.

Technical Specifications

Absolute Maximum Ratings

Parameter

MinMax

Units

Reference Document

VIN supply voltage

-0.53.6

V

Xilinx datasheet DS187, "Zynq-7000 All Programmable SoC: DC and AC Switching Characteristics".

Storage temperature

-40

+85

°C

Silicon Labs Si1141/42/43 datasheet.

Recommended Operating Conditions

ParameterMinMaxUnitsReference Document
Supply voltage1.143.465 VXilinx datasheet DS187, "Zynq-7000 All Programmable SoC: DC and AC Switching Characteristics".
Assembly variants for higher storage temperature range are available on request.

Physical Dimensions

  • Module size: 18 mm × 51 mm.  Please download the assembly diagram for exact numbers.

  • PCB thickness: 1.6 mm.

  • Highest part on PCB: approx. 4 mm. Please download the step model for exact numbers.

 All dimensions are given in millimeters.

 

Operating Temperature Ranges

Commercial grade: 0°C to +70°C.

Industrial grade: -40°C to +85°C.

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

Weight

... g - Plain module

... g - Set of bolts and nuts

Revision History

Hardware Revision History

DateRevision

Notes

PCNDocumentation Link
2015-10-2302   
 

01

 

  

Hardware revision number is printed on the PCB board together with the module model number separated by the dash.


Document Change History

Date

Revision

Contributors

Description

2017-02-09

Jan Kumann

Initial document.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • No labels