Download PDF version of this document.
Table of Contents
The Trenz Electronic TE0728 Carrier Board provides functionalities for testing, evaluation and development purposes of company's 6 x 6 cm SoMs. The Carrier Board is equipped with various components and connectors for different configuration setups and needs. The interfaces of the SoM's functional units and PL I/O-banks are connected via board-to-board connectors to the Carrier Board's components and connectors for easy user access.
See "6 x 6 SoM Carriers" page for more information about supported 6 x 6 cm SoMs.
Refer to http://trenz.org/te0728-info for the current online version of this manual and other available documentation.
There is no hardware component to be programmed on teh carrier.
Storage device name | Content | Notes |
---|---|---|
Signal | Designator | B2B | Jumper | Boot Mode |
---|---|---|---|---|
Boot_R | J4 | J2-11 | Open | QSPI |
Short | SD Card |
There is a user push button which is used for RESET signal.
Signal | Designator | B2B | Active Level |
---|---|---|---|
RESET | S1 | J2-7 | Active High |
Number of I/O signals FPGA bank numbers connected to the B2B connectors:
B2B Connector | Interfaces | Number of I/O | Notes |
---|---|---|---|
J1 | User I/O | 48 singel ended, 24 differential | Connected to Bank 13 |
4 Single ended | MIO10-13 | ||
CANH , CANL | 2 single ended | MIO8, MIO9 | |
J2 | User I/O | 22 singel ended, 11 differential | |
38 single ended | MIO16-53 | ||
SoM Control Signals | 5 | RESET, RST_OUT, BOOT_R, | |
JTAG Interface | 4 | TCK , TDO, TDI, TMS | |
J3 | User I/O | 20 Single ended, 10 differential | Connected to Bank 35 |
34 single ended, 17 differential | Connected to Bankd 33 | ||
Ethernet 1 | 4 single ended, 2 differential | ETH_CTREF , ETH_TD+, ETH_TD- , ETH_RD+, ETH_RD-, ETH_LED1, ETH_LED2, ETH_LED3 | |
Ethernet 2 | 4 single ended, 2 differential | ETH_CTREF , ETH_TD+, ETH_TD- , ETH_RD+, ETH_RD-, ETH_LED1, ETH_LED2, ETH_LED3 |
B2B Connector | Interfaces | Number of I/O | Notes |
---|---|---|---|
J5 | User I/O | 48 singel ended, 24 differential | Connected to Bank 13 |
34 single ended, 17 differential | Connected to Bank 33 | ||
J6 | User I/O | 42 singel ended, 21 differential | |
27 single ended | MIO16... MIO39 + MIO 51-53 | ||
4 single ended | MIO10-13 | ||
SoM Control Signals | 3 | RESET, RST_OUT, BOOT_R | |
JTAG Interface | 4 | TCK , TDO, TDI, TMS | |
CANH , CANL | 2 single ended | MIO8 , MIO9 |
JTAG access to the TE0728 Trenz Module through B2B connector J2. JTAG Programmer TE0790 is provided by Trenz Electronic, More information is available here.
Designator | Connected to | B2B Pin | Note |
---|---|---|---|
A | MIO52 | J2-15 | UART |
B | MIO53 | J2-16 | |
C | TMS | J2-12 | JTAG interface signal |
D | TDI | J2-10 | JTAG interface signal |
F | TDO | J2-8 | JTAG interface signal |
H | TCK | J2-6 | JTAG interface signal |
The DIP-switch S2 on JTAG interface is connected to JTAGEN.
S2 | ON | OFF | Default | Description |
---|---|---|---|---|
1 | Normal mode | Adapter board CPLD update mode | ON | Update Mode JTAG access to SC CPLD only |
2 | Do not use (illegal setting) | Normal mode | OFF | Must be in OFF state always. |
3 | VIO connected to 3.3V | Power VIO from pin header J2 | OFF | User I/O Voltage |
4 | Power 3.3V from USB | Power 3.3V from pin header J2 | OFF | Power on-board peripherals (FTDI chip & SC CPLD, ...) |
VDD for SD card holder is 3.3V.
Signals | Connected to | B2B | Notes |
---|---|---|---|
CD/DAT3 | MIO45 | J2-31 | |
CMD | MIO41 | J2-29 | |
CLK | MIO40_CLK | J2-34 | |
DAT0 | MIO42 | J2-37 | |
DAT1 | MIO43 | J2-40 | |
DAT2 | MIO44 | J2-32 | |
CD | MIO46 | J2-35 | |
WP | MIO47 | J2-33 |
Signal ETH1 | B2B | Signal ETH2 | B2B | Notes |
---|---|---|---|---|
ETH1_TD+ | J3-58 | ETH2_TD+ | J3-28 | Transfer |
ETH1_TD- | J3-56 | ETH2_TD- | J3-26 | |
ETH1_RD+ | J3_52 | ETH2_RD+ | J3-22 | Receive |
ETH1_RD- | J3-50 | ETH2_RD- | J3-20 | |
ETH1_CTREF | J3_57 | ETH2_CTREF | J3-25 | |
ETH1_LED1 | J3-55 | ETH2_LED1 | J3-23 | Yellow LED- Activity |
ETH1_LED3 | J3-51 | ETH2_LED3 | J3-19 | Green Green- Link |
Designator | Connected to | B2B | Active Level | Note |
---|---|---|---|---|
S1 | RESET | J2-7 | Active high | General Input RESET |
Designator | Connected to | B2B | Note |
---|---|---|---|
J4 | Boot_R | J2-11 | Open: QSPI |
Short: SD Card | |||
J11 | VCCIO | - | It connects VCCIO_13 to 3.3V or 1.8V. |
Designator | Color | Connected to | B2B | Active Level | Note |
---|---|---|---|---|---|
D1-A | Red | MIO48 | J2-30 | Active high | |
D1-B | Yellow | MIO49 | J2-38 | Active high | |
D1-C | Green | MIO50 | J2-36 | Active high |
Single 12V power supply with minimum current capability of 3.5A is recommended to operate the board.
Power Consumption
Power Input Pin | Typical Current |
---|---|
VIN | TBD* |
VBATT | TBD* |
* TBD - To Be Determined
No power supply protection circuit on the carrier, module will be powered directly.
Power Rail Name | B2B Connector | Direction | Notes |
---|---|---|---|
VIN | J1-1, J1-3 | Input | 5V |
VBAT | J2-1 | Input | Battery for RTC |
VCCO_13 | J1-39 | Input | Jumper(J11) connects VCCO_13 to 3.3v or 1.8v |
Module Connector (B2B) Designator | VCC / VCCIO | Direction | Pins | Notes |
---|---|---|---|---|
JB1 | VIN | In | 1,3 | Up to 12V carrier supply voltage |
3.3V | In | 19 | PL IO-bank VCCIO | |
VCCO_13 | In | 39 | 1.8V or 3.3V | |
JB2 | 3.3V | In | 2, 4 | 3.3V module supply voltage |
1.8V | In | 5 | PL IO-bank VCCIO | |
VBATT | In | 1 | RTC buffer voltage | |
JB3 | - | - | - | - |
On-board Connector Designator | VCC / VCCIO | Direction | Pins | Notes |
---|---|---|---|---|
Ja5 | VIN | In | A1,A2 | Up to 12V carrier supply voltage |
6 x 6 modules use two or three Samtec Micro Tiger Eye Connector on the bottom side.
3 x REF-189018-01 (compatible to TEM-140-02-03.0-H-D-A), (80 pins, "40" per row)
Parameter | Min | Max | Units | Note |
---|---|---|---|---|
VIN supply voltage | - | 5 | V |
Recommended Temprature: -40°C to +100°C.
Operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Parameter | Min | Max | Units | Note |
---|---|---|---|---|
VIN supply voltage | 5 | 5 | V |
Module size: 60 mm × 60 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 7 mm.
PCB thickness: 1.6 mm.
Trenz shop TE0728 overview page | |
---|---|
English page | German page |
Date | Revision | Note | PCN | Documentation Link |
---|---|---|---|---|
- | 01 | Prototypes | - | - |
Hardware revision number is printed on the PCB board next to the module model number separated by the dash.
Date | Revision | Contributor | Description |
---|---|---|---|
| |||
-- | all |
|
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
RoHS
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
WEEE
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.