You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 21 Next »

Key Features

  • Motor control evaluation with an suitable controller board 
  • Quick evaluation with reference motor board
  • Power option up to 48V and 30A main supply current

Block Diagram

Main Components

  • MOSFET Power Stage supporting 3-phase BLDC Motors
  • Current measurement on 2-phases (3 phase measurement optional)
  • Temperature sensor on board and 1-Wire bus connector for additional sensors
  • Encoder input capable of receiving both single ended and differential signals

General Safety Instructions

  • This product is only allowed to be used by an electrical specialist.
  • This product is not allowed to be used unattended.
  • There is a possible risk of burns due to hot surfaces while running the Board. This e.g. might be caused by an overcurrent at the motor outputs.
  • All externally connected power sources must be SELV protected (Separated or safety extra-low voltage).
  • For set up the wiring switch off or disconnect all external power supplies.
  • During operations it is not allowed to change the wiring or mechanical setup.
  • This product is only allowed to be used in a dry indoor environment.
  • The product is only allowed to be used in horizontal position on a non-conducting and non-inflammable surface.
  • The mechanical setup must ensure that the whole test setup can not be dropped to the floor or moved accidentally.

Signals, Interfaces and Pins

Control Board Connections


Signal namesConnector J8Connector J9Connector J17

Digital Supply to EDPS

Pin 6, 12: +3.3V
Pin 5, 11: GND

Pin 6, 12: +3.3V
Pin 5, 11: GND
Pin 5, 6, 21, 22: +3.3V
Pin 1, 2, 25, 26: GND

Motor Driver PWM Signals to EDPS

High and Low Side control signals
are
hardware protected against
simultaniously
ON switching
of the MOSFETs

 

Pin 1: G1H - Ch.A HighSide
Pin 7: G1L - Ch.A LowSide
Pin 2: G2H - Ch.B HighSide
Pin 8: G2L - Ch.B LowSide
Pin 3: G3H - Ch.C HighSide
Pin 9: G3L - Ch.C LowSide

 

Pin 11: G1H - Ch.A HighSide
Pin 12: G1L - Ch.A LowSide
Pin 9: G2H - Ch.B HighSide
Pin 10: G2L - Ch.B LowSide
Pin 7: G3H - Ch.C HighSide
Pin 8: G3L - Ch.C LowSide

ADC Clock Signal to EDPS Pin 1: SCLKPin 23: SCLK
Encoder Digital Signals from EDPS 

Pin 8: ENC_A
Pin 9: ENC_B
Pin 10: ENC_I

Pin 20: ENC_A
Pin 18: ENC_B
Pin 16: ENC_I

Motor Current ADC "raw" Signals from EDPS
(usable with FPGA IP)
 

Pin 2: SDI1 - Current Ch.A
Pin 3: SDI2 - Current Ch.B
Pin 4: SDI3 - Current Ch.C

Pin 19: SDI1 - Current Ch.A
Pin 17: SDI2 - Current Ch.B
Pin 15: SDI3 - Current Ch.C

Supply Voltage ADC "raw" Signal from EDPS
(usable with FPGA IP)
 

Pin 7: SDIV - from DC_LINK
(Fused Motor Supply Voltage)

Pin 24: SDIV - from DC_LINK
(Fused Motor Supply Voltage)

1-Wire bus for temperature measurementPin 10: EXT1 - 1-Wire Bus 1
Pin 4: EXT2 - 1-Wire Bus 2
 

Pin 4: EXT1 - 1-Wire Bus 1
Pin 3: EXT2 - 1-Wire Bus 2

Not connected pinsnonenonePin 13, 14

Motor and Power Connections

There are two options available for the motor and power concept:

DetailOption 1: Reference Motor Board with DC +12V SupplyOption 2: Customer Motor at individual DC +5..48VComments
Motor Supply

From DC +12V Input J7 via Fuse F3 (TODO ... A)
via Motor Reference Board to J5 of Drive board

From customer DC Supply to J6 via F1 on Drive Boad 
Motor ConnectionMotor wires connected to cage clamps on
Motor Reference Board J5 (A), J4 (B), J3 (C)
Motor wires connected to bolt screw terminals on
Drive Board J2 (A), J3 (B), J4 (C)
 

Encoder Connection

Single Ended

From encoder pins via 6Pin PMoD to Drive Board J10:

J10 single ended:

Pin 1: GND
Pin 2: ENC I input
Pin 3: ENC A input
Pin 4: +5V Supply
Pin 5: ENC B input
Pin 6: GND

From motor to Drive Board to J11 (single/differential):

J11 single ended:

Pin 2: +5V Supply
Pin 3: GND
Pin 6: ENC A input
Pin 8: ENC B input
Pin 10: ENC I input


Jumper Settings for encoder signals.



Single Ended:           Differential:
    

 

Encoder Connection

Differential
 J11 differential with 100R terminated:
Pin 2: +5V Supply
Pin 3: GND
Pin 5: ENC A negativ
Pin 6: ENC A positiv
Pin 7: ENC B negativ
Pin 8: ENC B positiv
Pin 9: ENC I negativ
Pin 10: ENC I positiv

Internal

Temperature Sensor

Onboard is a Maxim 1-Wire Temperature sensor DS18S20Z+. This sensor is located in the middle of the PCB.
Addional 1-Wire sensor(s) can be connected to the connector J16:

 

  • Pin 1(DQ), 3 (GND),5 (+3.3V) at the same 1-wire bus as the onboard one
  • Pin 2(DQ), 4 (GND),6 (+3.3V) at a separate 1-wire bus

Power and Power-On Sequence

DC 12V Supply Motor and Driver

The power source must be SELV (Separated or safety extra-low voltageprotected.

The motor drivers and the reference motor on the pre-mounted motor board TEC0060 are supplied by this voltage.

The internal +5V digital supply is generated from this +12V supply.

DC 5...48V Supply for Motor only

SAFETY INSTRUCTIONS:

Externally power supply for the motor must be SELV (Separated or safety extra-low voltageprotected.

This option is

  • only allowed to be used for electrical specialist for the used electrical voltage and power conditions
  • only allowed to be used under electrical laboratory conditions
  • only allowed to be used in horizontal position on a non-conducting and non-inflammable surface
  • only allowed to be used with a wiring, which fulfills the current rating for the maximum possible currents.
  • only allowed to be used with a suitable current limiting circuit
    • The maximum continuous current must not exceed 30A.
    • The delivered fuse "Littelfuse Tpye 142.5631.5302" must be used as current limiter between connector J5 and J6.
    • To limit the current for smaller motor loads an ADDITIONALLY appropriate current limiter can be used e.g. a current limited power source or a fuse integrated in the wiring.
  • only allowed to be used with appropriate connectors at the M5 screw connectors, which means M5 cable lugs must be used and fastened according to technical standards.
  • only allowed to be used, if the "Drive Boad high current signals" conducting up to 30A nominal, are covered by isolating, mechanically stable, non-inflammable (UL V-1 or better) material
    • The "Drive Board high current signals" are the motor outputs A, B, C and Fuse F1 Connectors J5 an J6 and further internal connections shown white marked in the following picture:

    • As minimum protection it is mandatory to use the delivered "Isolating cover PCB" (marked in green), which must be mounted to the mounting holes H1, H9, H3, H4 with the delivered 10mm isolating spacers:


    • The used cable lugs need to be isolated in the area outstanding the outer border of the Drive Board
      Make sure that the "Isolating Cover PCB" is overlapping the conducting material by a minimum of 20 mm.

Initial operation

To use a separate power supply for the motor supply perform the following steps:

  1. Disconnect the reference motor board TEC0060 by unmounting its screws and the encoder cable from J10
  2. Mount the delivered 30A fuse to the connectors J5 and J6 with the delivered M5 screws
    1. For lower supply current requirements, caused by the power rating of the used motor, a fuse with a lower and suitable current rating integrated in the supply wiring is recommended.
  3. Connect with cable lugs the +DC 5..48V to J6 and the corresponding GND to J1.
    1. The cable length is limited to 3m.
  4. Connect the three motor phases to J2 (A), J3 (B) and J4 (C).
    1. The cable length is limited to 3m.
  5. Optional: connect the encoder to J10 or J11 and set jumper field according to signal specification: differential or single ended. See section TODO for details.

Power-On Sequence

Any power sequence of the three supply sources is allowed:

  • +3V3 Supply from the Control Board, generated by Control Board supply
  • +12V and
  • optional +5..48V Motor Supply

Reference Motor Board TEC0060

For easy connection of the reference Motor and Encoder to the Driver board a special Motor Adapter Board TEC0060 is included in the EDDP Kit.

Reference Motor

The reference motor is manufactured by Anaheim Automation. The order code for the motor with the encoder already mounted is BLWR111D-24V-10000-1000SI. Please note that the encoder is not available separately. The nominal motor voltage is DC 24V, however, only 12V is supplied by the Reference Motor Board, which results in reduced performance.

The datasheet for the motor can be found at
http://www.anaheimautomation.com/manuals/brushless/L010234%20-%20BLWR11%20Series%20Product%20Sheet.pdf

The datasheet for the encoder can be found at
http://www.anaheimautomation.com/manuals/accessories/L010390%20-%20Single%20Ended%20Encoder%20with%20Index%20Channel.pdf

Technical Specifications

Absolute Maximum Ratings

ParameterMinMax

Units

Notes

DC +12V supply

015

V

 
DC +5..48V supply050VV 
DC +3V3 supply-0.56V 
PWM Input-0.56V 
ADC Digital Input-0.53.8VDC +3V3 = 3.3V
Encoder Input-1015V 

Recommended Operating Conditions

ParameterMinMax

Units

Notes

DC +12V supply

11.512.5

V

 
DC +5..48V supply548V 
DC +3V3 supply3.03.6V 
PWM Input0DC +3V3 supplyV 
ADC Digital Input0DC +3V3 supplyV 
Encoder Input-712V 

Electrical characteristics

DC +3V3 supply = 3.3V

ParameterMinMax

Units

Notes
PWM Input Logic High Level2.2 V 
PWM Input Logic Low Level 0.8V 
ADC Digital Input Logic High Level2.7 V 
ADC Digital Input Logic Low Level 0.6V 
ADC Digital Output Logic High Level3.23.3VIo=-200μA
ADC Digital Output Logic Low Level00.4VIo=+200μA
Encoder Input Logic High Level (Differential) -0.2V 
Encoder Input Logic Low Level (Differential)-0.01 V 
Encoder Input Logic High Level (Single Ended)2 V 
Encoder Input Logic Low Level (Single Ended) 0.6V 

Physical Dimensions

  • Board size: 100 mm × 166 mm.  Please download the assembly diagram for exact numbers.

  • PCB thickness: 1.75 mm +/-10%

  • Highest part on PCB: approximately 17 mm. Please download the step model for exact numbers.

All dimensions are shown in mm. Additional sketches, drawings and schematics can be found TODO: here.

Operating Temperature Ranges

0°C - 70°C, cooling might be required, depending on environment and airflow.

References

All resource links for other relevant documents and websites are available from Trenz EDDP Web Hub:

http://trenz.org/EDDP

Revision History

Hardware Revision History

DateRevision

Notes

PCN LinkDocumentation Link
2016-03-2702  TEC0053-02
2017-08-1404   

Hardware revision number is printed on the PCB board in the bottom right corner.

Document Change History

Date

Revision

Authors

Description

2017-03-30

 

Andreas HeidemannInitial Version

Disclaimer

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.

 

  • No labels